Your message dated Sat, 25 Jul 2009 11:15:03 +0200
with message-id <20090725091503.ga32...@galadriel.inutil.org>
and subject line Re: installation-reports
has caused the Debian Bug report #298260,
regarding Installer boot hangs with HP NetRaid controllers present
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact ow...@bugs.debian.org
immediately.)
--
298260: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=298260
Debian Bug Tracking System
Contact ow...@bugs.debian.org with problems
--- Begin Message ---
Package: installation-reports
Debian-installer-version: sarge-i386-1 ISO dated 2/28/05
uname -a: N/A
Date: 3/5/05 23:30
Method: SCSI CD Boot hooked to integrated Adaptec 7880
SCSI controller (i.e. CD not connected to RAID controller)
Machine: HP Netserver LX Pro with HP NetRaid controller - applied
latest firmware from HP's site for system and controller
Processor: Dual Pentium Pro 200
Memory: 524288 KB
Root Device: N/A
Root Size/partition table: N/A
Output of lspci and lspci -n: N/A
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [E]
Configure network HW: [ ]
Config network: [ ]
Detect CD: [ ]
Load installer modules: [ ]
Detect hard drives: [ ]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
Boot off of CD is successful.
Debian Installer spash screen appears with "...Enter to boot:"
Press Enter and get:
Loading /install/vmlinuz.....
Loading /install/initrd.gz......
Screen goes blank and flashing cursor appears in upper-right
corner of screen and just sits there. System is hung at this
point and I need to press Reset button.
Tried 'debian-installer/framebuffer=false' but this didn't help.
Also tried 'netcfg/disable_dhcp=true' with the above - no help.
Rebooted and pressed F1 and then F6 to read about special disk
drives and when I press Enter from this screen I get:
Loading /install/vmlinuz....
Loading /install/initrd.gz.....
Ready.
and then get a CR/LF and the cursor flashes below the 'R' of
'Ready.' and just sits there. System is hung at this point.
There is no USB or PCMCIA on this system so I didn't bother
trying those related boot parameters. Didn't see any reference
to either the 7880 or NetRAID controllers on the F6 boot
parameters screen.
This same system loads Woody with no problems.
Keith Parkansky
Network Specialist
Milwaukee County IMSD
--- End Message ---
--- Begin Message ---
On Fri, Dec 26, 2008 at 08:39:28PM +0100, Moritz Muehlenhoff wrote:
> reassign 298260 linux-2.6
> thanks
>
> On Sun, Mar 06, 2005 at 12:08:31AM -0600, kparkan...@milwcnty.com wrote:
> > Package: installation-reports
> >
> > Debian-installer-version: sarge-i386-1 ISO dated 2/28/05
> > uname -a: N/A
> > Date: 3/5/05 23:30
> > Method: SCSI CD Boot hooked to integrated Adaptec 7880
> > SCSI controller (i.e. CD not connected to RAID controller)
> >
> > Machine: HP Netserver LX Pro with HP NetRaid controller - applied
> > latest firmware from HP's site for system and controller
> > Processor: Dual Pentium Pro 200
> > Memory: 524288 KB
> > Root Device: N/A
> > Root Size/partition table: N/A
> > Output of lspci and lspci -n: N/A
> >
> > Boot off of CD is successful.
> > Debian Installer spash screen appears with "...Enter to boot:"
> > Press Enter and get:
> > Loading /install/vmlinuz.....
> > Loading /install/initrd.gz......
> > Screen goes blank and flashing cursor appears in upper-right
> > corner of screen and just sits there. System is hung at this
> > point and I need to press Reset button.
> > Tried 'debian-installer/framebuffer=false' but this didn't help.
> > Also tried 'netcfg/disable_dhcp=true' with the above - no help.
> > Rebooted and pressed F1 and then F6 to read about special disk
> > drives and when I press Enter from this screen I get:
> > Loading /install/vmlinuz....
> > Loading /install/initrd.gz.....
> > Ready.
> > and then get a CR/LF and the cursor flashes below the 'R' of
> > 'Ready.' and just sits there. System is hung at this point.
> > There is no USB or PCMCIA on this system so I didn't bother
> > trying those related boot parameters. Didn't see any reference
> > to either the 7880 or NetRAID controllers on the F6 boot
> > parameters screen.
> >
> > This same system loads Woody with no problems.
>
> Does this error still occur with more recent kernel versions?
No further feedback, closing the bug.
If anyone reencounters the problem, please reopen this bug.
Cheers,
Moritz
--- End Message ---
