Package: linux-image-2.6.26-2-amd64
Version: 2.6.26-17
Severity: normal
The RealTek 8111c chipset, frequently used in mainboards from many
manufacturers, is not supported in the 2.6.26 kernel. I've tried the
Ubuntu 9.04 distro and it does work with their 2.6.28 kernel. RealTek
offer the source for a Linux driver on their web site that, according to
some reports I've seen re. getting it to work with earlier Ubuntu
versions, works back to at least kernel 2.6.24.
I'd compile the module but aptitude reports problems getting everything
I need. SO for now I'm using an old Linksys 10/100 USB Ethernet adapter.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-amd64 (Debian 2.6.26-17) (da...@debian.org) (gcc
version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 21
04:47:08 UTC 2009
** Command line:
root=/dev/md2 ro
** Not tainted
** Kernel log:
[ 11.831094] usbcore: registered new interface driver pegasus
[ 12.171598] input: PC Speaker as /class/input/input4
[ 12.209500] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level,
low) -> IRQ 16
[ 12.247999] hda_codec: Unknown model for ALC882, trying auto-probe
from BIOS...
[ 12.253966] input: ImExPS/2 Generic Explorer Mouse as /class/input/input5
[ 12.265119] cx23885 driver version 0.0.1 loaded
[ 12.285120] ACPI: PCI Interrupt 0000:01:05.1[B] -> GSI 19 (level,
low) -> IRQ 19
[ 12.285202] PCI: Setting latency timer of device 0000:01:05.1 to 64
[ 12.331141] Error: Driver 'pcspkr' is already registered, aborting...
[ 12.334057] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level,
low) -> IRQ 18
[ 12.334203] CORE cx23885[0]: subsystem: 0070:7911, board: Hauppauge
WinTV-HVR1250 [card=3,autodetected]
[ 12.438975] cx23885[0]: i2c bus 0 registered
[ 12.438975] cx23885[0]: i2c bus 1 registered
[ 12.438975] cx23885[0]: i2c bus 2 registered
[ 12.466976] tveeprom 1-0050: Encountered bad packet header [ff].
Corrupt or not a Hauppauge eeprom.
[ 12.466976] cx23885[0]: warning: unknown hauppauge model #0
[ 12.466976] cx23885[0]: hauppauge eeprom: model=0
[ 12.466976] cx23885[0]: cx23885 based dvb card
[ 12.581972] MT2131: successfully identified at address 0x61
[ 12.581972] DVB: registering new adapter (cx23885[0])
[ 12.581972] DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB
Frontend)...
[ 12.581972] cx23885_dev_checkrevision() Hardware revision = 0xc0
[ 12.581972] cx23885[0]/0: found at 0000:02:00.0, rev: 3, irq: 18,
latency: 0, mmio: 0xfd600000
[ 12.581972] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 13.552758] ov511: Failed to read sensor ID. You might not have an
[ 13.552758] ov511: OV7610/20, or it may be not responding. Report
[ 13.552758] ov511: this to m...@alpha.dyndns.org
[ 13.552758] ov511: This is only a warning. You can attempt to use
[ 13.552758] ov511: your camera anyway
[ 13.708727] ov511: Sensor is an OV7610
[ 14.471631] ov511: Device at usb-0000:00:12.1-2 registered to minor 0
[ 14.471683] usbcore: registered new interface driver ov511
[ 14.471715] ov511: v1.64 for Linux 2.5 : ov511 USB Camera Driver
[ 15.350755] Adding 2008116k swap on /dev/sda3. Priority:-1 extents:1
across:2008116k
[ 15.363547] Adding 2008116k swap on /dev/sdb3. Priority:-2 extents:1
across:2008116k
[ 15.866342] EXT3 FS on md2, internal journal
[ 16.364299] ide_generic: please use "probe_mask=0x3f" module
parameter for probing all legacy ISA IDE ports
[ 16.364299] ide_generic: I/O resource 0x1F0-0x1F7 not free.
[ 16.364299] ide_generic: I/O resource 0x170-0x177 not free.
[ 16.410868] it87: Found IT8718F chip at 0x228, revision 5
[ 16.410868] it87: in3 is VCC (+5V)
[ 16.410868] hwmon-vid: Unknown VRM version of your x86 CPU
[ 16.484813] device-mapper: uevent: version 1.0.3
[ 16.484813] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18)
initialised: dm-de...@redhat.com
[ 17.598202] fuse init (API version 7.9)
[ 17.661005] kjournald starting. Commit interval 5 seconds
[ 17.667061] EXT3-fs warning: maximal mount count reached, running
e2fsck is recommended
[ 17.690839] EXT3 FS on md0, internal journal
[ 17.690839] EXT3-fs: mounted filesystem with ordered data mode.
[ 17.902649] kjournald starting. Commit interval 5 seconds
[ 18.035045] EXT3 FS on md1, internal journal
[ 18.035045] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.950122] eth0: set allmulti
[ 18.950576] eth0: set allmulti
[ 20.154585] eth0: set allmulti
[ 20.154628] eth0: set allmulti
[ 21.142076] NET: Registered protocol family 10
[ 21.142076] lo: Disabled Privacy Extensions
[ 21.142076] eth0: set allmulti
[ 21.142076] eth0: set allmulti
[ 23.876858] eth0: set allmulti
[ 23.876858] eth0: set allmulti
[ 42.073045] kvm: Nested Paging enabled
[ 50.406387] pnp: the driver 'parport_pc' has been registered
[ 50.406387] lp: driver loaded but no devices found
[ 50.444684] ppdev: user-space parallel port driver
[ 53.082248] mtrr: no more MTRRs available
[ 53.082278] mtrr: no more MTRRs available
[ 53.082286] mtrr: no more MTRRs available
[ 53.082293] mtrr: no more MTRRs available
[ 53.082300] mtrr: no more MTRRs available
[ 53.082307] mtrr: no more MTRRs available
[ 53.082314] mtrr: no more MTRRs available
[ 73.918792] CPU0 attaching NULL sched-domain.
[ 73.918792] CPU1 attaching NULL sched-domain.
[ 73.918792] CPU2 attaching NULL sched-domain.
[ 73.918792] CPU3 attaching NULL sched-domain.
[ 73.926907] CPU0 attaching sched-domain:
[ 73.926914] domain 0: span 0-3
[ 73.926917] groups: 0 1 2 3
[ 73.926927] domain 1: span 0-3
[ 73.926931] groups: 0-3
[ 73.926936] CPU1 attaching sched-domain:
[ 73.926938] domain 0: span 0-3
[ 73.926943] groups: 1 2 3 0
[ 73.926953] domain 1: span 0-3
[ 73.926958] groups: 0-3
[ 73.926964] CPU2 attaching sched-domain:
[ 73.926966] domain 0: span 0-3
[ 73.926970] groups: 2 3 0 1
[ 73.926981] domain 1: span 0-3
[ 73.926985] groups: 0-3
[ 73.926991] CPU3 attaching sched-domain:
[ 73.926993] domain 0: span 0-3
[ 73.926998] groups: 3 0 1 2
[ 73.927008] domain 1: span 0-3
[ 73.927011] groups: 0-3
[ 87.172251] RPC: Registered udp transport module.
[ 87.172251] RPC: Registered tcp transport module.
[ 91.265317] hda-intel: Invalid position buffer, using LPIB read
method instead.
** Loaded modules:
Module Size Used by
nls_utf8 6272 2
cifs 235408 2
nls_base 12932 2 nls_utf8,cifs
nfs 251696 1
lockd 68944 1 nfs
nfs_acl 7552 1 nfs
sunrpc 197992 11 nfs,lockd,nfs_acl
ppdev 11656 0
parport_pc 31016 0
lp 14724 0
parport 41776 3 ppdev,parport_pc,lp
kvm_amd 29580 0
kvm 127464 1 kvm_amd
ac 9352 0
battery 16776 0
container 8320 0
sbs 17808 0
sbshc 10368 1 sbs
video 24084 0
output 7808 1 video
ipv6 288328 39
fuse 53184 1
dm_snapshot 19400 0
dm_mirror 20608 0
dm_log 13956 1 dm_mirror
dm_mod 58864 3 dm_snapshot,dm_mirror,dm_log
it87 28952 0
hwmon_vid 7296 1 it87
ide_generic 7168 0 [permanent]
ide_cd_mod 36360 0
mt2131 10116 1
s5h1409 13444 1
cx23885 97972 0
firmware_class 12544 1 cx23885
snd_hda_intel 436440 2
snd_pcsp 14588 3
cx2341x 15876 1 cx23885
videobuf_dma_sg 17412 1 cx23885
v4l2_common 16384 2 cx23885,cx2341x
snd_pcm_oss 41760 0
btcx_risc 9096 1 cx23885
tveeprom 17924 1 cx23885
snd_mixer_oss 18816 1 snd_pcm_oss
videobuf_dvb 9604 1 cx23885
snd_pcm 81672 4 snd_hda_intel,snd_pcsp,snd_pcm_oss
dvb_core 82740 1 videobuf_dvb
snd_timer 25744 2 snd_pcm
ov511 75024 0
i2c_piix4 13072 0
compat_ioctl32 12288 2 cx23885,ov511
snd 63688 14
snd_hda_intel,snd_pcsp,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
videodev 35840 3 cx23885,ov511,compat_ioctl32
pegasus 28568 0
serio_raw 9860 0
psmouse 42268 0
soundcore 12064 1 snd
v4l1_compat 17284 2 cx23885,videodev
videobuf_core 23300 3 cx23885,videobuf_dma_sg,videobuf_dvb
mii 9856 1 pegasus
i2c_core 27936 6
mt2131,s5h1409,cx23885,v4l2_common,tveeprom,i2c_piix4
shpchp 34208 0
pci_hotplug 32056 1 shpchp
snd_page_alloc 13072 2 snd_hda_intel,snd_pcm
wmi 11712 0
button 11680 0
evdev 14208 3
ext3 124944 3
jbd 51240 1 ext3
mbcache 12804 1 ext3
raid456 125472 2
async_xor 8448 1 raid456
async_memcpy 6912 1 raid456
async_tx 11764 3 raid456,async_xor,async_memcpy
xor 9744 2 raid456,async_xor
raid1 23936 1
md_mod 80164 5 raid456,raid1
sg 36576 0
ide_disk 16512 8
sd_mod 29376 10
sr_mod 19652 0
cdrom 37928 2 ide_cd_mod,sr_mod
ata_generic 10116 0
ide_pci_generic 9220 0 [permanent]
ohci1394 32692 0
ieee1394 93816 1 ohci1394
atiixp 8324 0 [permanent]
ahci 33036 10
ide_core 128284 5
ide_generic,ide_cd_mod,ide_disk,ide_pci_generic,atiixp
ohci_hcd 25092 0
libata 165600 2 ata_generic,ahci
ehci_hcd 35980 0
scsi_mod 160760 4 sg,sd_mod,sr_mod,libata
dock 14112 1 libata
r8169 31492 0
thermal 22816 0
processor 42304 1 thermal
fan 9352 0
thermal_sys 17728 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host
Bridge [1022:9600]
Subsystem: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI
bridge (int gfx) [1022:9602] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fd900000-fdafffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI
bridge (PCIE port 2) [1022:9606] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fd600000-fd7fffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:0a.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI
bridge (PCIE port 5) [1022:9609] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA
Controller [IDE mode] [1002:4390] (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1
Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI
Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1
Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI
Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller
[1002:4385] (rev 3a)
Subsystem: Giga-byte Technology Device [1458:4385]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR+ <PERR+ INTx-
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE
Controller [1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fa00 [size=16]
Capabilities: <access denied>
Kernel driver in use: ATIIXP_IDE
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel
HDA) [1002:4383]
Subsystem: Giga-byte Technology Device [1458:a102]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host
controller [1002:439d]
Subsystem: ATI Technologies Inc SB700/SB800 LPC host controller
[1002:439d]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge
[1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: fdb00000-fdbfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron,
Athlon64, Sempron] HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron,
Athlon64, Sempron] Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron,
Athlon64, Sempron] DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron,
Athlon64, Sempron] Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] K10 [Opteron,
Athlon64, Sempron] Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon HD
3300 Graphics [1002:9614] (prog-if 00 [VGA controller])
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at ee00 [size=256]
Region 2: Memory at fdae0000 (32-bit, non-prefetchable) [size=64K]
Region 5: Memory at fd900000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
01:05.1 Audio device [0403]: ATI Technologies Inc RS780 Azalia
controller [1002:960f]
Subsystem: Giga-byte Technology Device [1458:960f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fdafc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
02:00.0 Multimedia video controller [0400]: Conexant Systems, Inc.
CX23885 PCI Video and Audio Decoder [14f1:8852] (rev 03)
Subsystem: Hauppauge computer works Inc. Device [0070:7911]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fd600000 (64-bit, non-prefetchable) [size=2M]
Capabilities: <access denied>
Kernel driver in use: cx23885
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 1277
Region 0: I/O ports at ce00 [size=256]
Region 2: Memory at fddff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fdde0000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at fdd00000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
04:07.0 Serial controller [0700]: NetMos Technology PCI 9835 Multi-I/O
Controller [9710:9835] (rev 01) (prog-if 02 [16550])
Subsystem: LSI Logic / Symbios Logic 2S (16C550 UART) [1000:0002]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at bf00 [size=8]
Region 1: I/O ports at be00 [size=8]
Region 2: I/O ports at bd00 [size=8]
Region 3: I/O ports at bc00 [size=8]
Region 4: I/O ports at bb00 [size=8]
Region 5: I/O ports at ba00 [size=16]
Kernel driver in use: serial
04:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fdcff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fdcf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_CA.UTF-8, LC_CTYPE=en_CA.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.27 Debian configuration
management sy
ii initramfs-tools [linux-initra 0.93.3 tools for generating an
initramfs
ii module-init-tools 3.9-2 tools for managing Linux
kernel mo
linux-image-2.6.26-2-amd64 recommends no packages.
-- debconf information excluded
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
