--- Begin Message ---
Package: linux-image-2.6.28-1-amd64
Version: 2.6.28-1
Severity: important
File: linux-image-2.6.28
When coming back from s2disk I have to:
. ifdown wlan0
. rmmod iwl3945
. modprobe iwl3945
. ifup wlan0
In the mean time, I use my notebook in a BSS environment. As soon as the
notebook is out of the range of the AP on which he is connected, he looses
the wireless connection instead of switching to another AP in his area. I made
the same test with an eeePC (Lenny) and a Nokia E65 phone, they work
correctly meaning that they switch to the other AP.
I hadn't those problems with a 2.6.26 kernel.
-- Package-specific info:
** Version:
Linux version 2.6.28-1-amd64 (Debian 2.6.28-1) (m...@debian.org) (gcc version
4.3.3 (Debian 4.3.3-4) ) #1 SMP Wed Feb 18 17:16:12 UTC 2009
** Command line:
root=/dev/mapper/vg0-Dom0 ro vga=791 quiet
** Not tainted
** Kernel log:
[109158.801983] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection
driver for Linux, 1.2.26ks
[109158.801989] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[109158.802084] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[109158.802102] iwl3945 0000:0b:00.0: setting latency timer to 64
[109158.802176] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[109158.844119] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[109158.848810] phy9: Selected rate control algorithm 'iwl-3945-rs'
[109165.188447] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[109165.188806] iwl3945 0000:0b:00.0: irq 4349 for MSI/MSI-X
[109165.188920] iwl3945 0000:0b:00.0: firmware: requesting iwlwifi-3945-1.ucode
[109165.258229] Registered led device: iwl-phy9:radio
[109165.258306] Registered led device: iwl-phy9:assoc
[109165.258337] Registered led device: iwl-phy9:RX
[109165.258371] Registered led device: iwl-phy9:TX
[109165.273478] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[109167.367031] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[109167.367380] iwl3945 0000:0b:00.0: irq 4349 for MSI/MSI-X
[109167.413959] Registered led device: iwl-phy9:radio
[109167.414036] Registered led device: iwl-phy9:assoc
[109167.414066] Registered led device: iwl-phy9:RX
[109167.414096] Registered led device: iwl-phy9:TX
[109167.428194] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[109167.435751] wlan0: authenticate with AP 00:1e:e5:64:e1:b2
[109167.437578] wlan0: authenticated
[109167.437584] wlan0: associate with AP 00:1e:e5:64:e1:b2
[109167.440257] wlan0: RX AssocResp from 00:1e:e5:64:e1:b2 (capab=0x411
status=0 aid=1)
[109167.440263] wlan0: associated
[109167.442244] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[109178.009021] wlan0: no IPv6 routers present
[109297.816136] b44: eth0: Link is down.
[109300.816226] b44: eth0: Link is up at 100 Mbps, full duplex.
[109300.816232] b44: eth0: Flow control is off for TX and off for RX.
[109361.816102] b44: eth0: Link is down.
[109363.816194] b44: eth0: Link is up at 100 Mbps, full duplex.
[109363.816199] b44: eth0: Flow control is off for TX and off for RX.
[109526.816133] b44: eth0: Link is down.
[109529.820110] b44: eth0: Link is up at 100 Mbps, full duplex.
[109529.820115] b44: eth0: Flow control is off for TX and off for RX.
[109597.817123] b44: eth0: Link is down.
[109615.472027] wlan0: No ProbeResp from current AP 00:1e:e5:64:e1:b2 - assume
out of range
[109695.123176] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection
driver for Linux, 1.2.26ks
[109695.123182] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[109695.123290] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[109695.123308] iwl3945 0000:0b:00.0: setting latency timer to 64
[109695.123469] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[109695.174257] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[109695.177037] phy10: Selected rate control algorithm 'iwl-3945-rs'
[109699.727076] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[109699.727432] iwl3945 0000:0b:00.0: irq 4349 for MSI/MSI-X
[109699.727542] iwl3945 0000:0b:00.0: firmware: requesting iwlwifi-3945-1.ucode
[109699.786198] Registered led device: iwl-phy10:radio
[109699.786222] Registered led device: iwl-phy10:assoc
[109699.786284] Registered led device: iwl-phy10:RX
[109699.786303] Registered led device: iwl-phy10:TX
[109699.808209] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[109701.870363] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[109701.870694] iwl3945 0000:0b:00.0: irq 4349 for MSI/MSI-X
[109701.914167] Registered led device: iwl-phy10:radio
[109701.914189] Registered led device: iwl-phy10:assoc
[109701.914248] Registered led device: iwl-phy10:RX
[109701.914266] Registered led device: iwl-phy10:TX
[109701.942740] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[109701.946783] wlan0: authenticate with AP 00:1e:e5:64:e1:b2
[109701.948603] wlan0: authenticated
[109701.948606] wlan0: associate with AP 00:1e:e5:64:e1:b2
[109701.951369] wlan0: RX AssocResp from 00:1e:e5:64:e1:b2 (capab=0x411
status=0 aid=1)
[109701.951372] wlan0: associated
[109701.953604] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[109712.844441] wlan0: no IPv6 routers present
[109916.216218] b44: eth0: powering down PHY
[115118.104083] wlan0: No ProbeResp from current AP 00:1e:e5:64:e1:b2 - assume
out of range
[115194.405379] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection
driver for Linux, 1.2.26ks
[115194.405385] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[115194.405470] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[115194.405487] iwl3945 0000:0b:00.0: setting latency timer to 64
[115194.405703] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[115194.453479] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[115194.457519] phy11: Selected rate control algorithm 'iwl-3945-rs'
[115199.650038] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[115199.650397] iwl3945 0000:0b:00.0: irq 4349 for MSI/MSI-X
[115199.650500] iwl3945 0000:0b:00.0: firmware: requesting iwlwifi-3945-1.ucode
[115199.714269] Registered led device: iwl-phy11:radio
[115199.714343] Registered led device: iwl-phy11:assoc
[115199.714373] Registered led device: iwl-phy11:RX
[115199.714402] Registered led device: iwl-phy11:TX
[115199.725634] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[115201.880072] iwl3945 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[115201.880429] iwl3945 0000:0b:00.0: irq 4349 for MSI/MSI-X
[115201.934289] Registered led device: iwl-phy11:radio
[115201.934364] Registered led device: iwl-phy11:assoc
[115201.934394] Registered led device: iwl-phy11:RX
[115201.934422] Registered led device: iwl-phy11:TX
[115201.949709] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[115201.953570] wlan0: authenticate with AP 00:1e:e5:64:e1:b2
[115201.955409] wlan0: authenticated
[115201.955414] wlan0: associate with AP 00:1e:e5:64:e1:b2
[115201.958286] wlan0: RX AssocResp from 00:1e:e5:64:e1:b2 (capab=0x411
status=0 aid=1)
[115201.958292] wlan0: associated
[115201.964654] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[115212.008038] wlan0: no IPv6 routers present
** Loaded modules:
Module Size Used by
iwl3945 152680 0
i915 123272 2
drm 167888 3 i915
binfmt_misc 74892 1
rfcomm 102304 0
l2cap 86656 3 rfcomm
ppdev 73096 0
lp 75876 0
parport 103328 2 ppdev,lp
tun 76676 1
snd_atiixp_modem 78732 0
snd_via82xx_modem 77580 0
snd_intel8x0m 80656 0
snd_ac97_codec 179400 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m
ac97_bus 67584 1 snd_ac97_codec
cpufreq_userspace 69252 0
cpufreq_powersave 67328 0
cpufreq_conservative 72712 0
cpufreq_stats 70404 0
nfsd 312832 17
auth_rpcgss 105744 1 nfsd
exportfs 70272 1 nfsd
nfs 320304 0
lockd 132212 2 nfsd,nfs
nfs_acl 68864 2 nfsd,nfs
sunrpc 262760 15 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
ipv6 348928 34
isofs 96664 1
zlib_inflate 81408 1 isofs
udf 136728 0
ext3 186768 1
jbd 116264 1 ext3
mbcache 74628 1 ext3
nls_utf8 67584 1
nls_cp437 72448 1
vfat 76288 1
fat 115384 1 vfat
nls_base 74372 6 isofs,udf,nls_utf8,nls_cp437,vfat,fat
kvm_intel 110544 0
kvm 213288 1 kvm_intel
snd_seq 115568 0
snd_seq_device 73108 1 snd_seq
acpi_cpufreq 74000 0
firewire_sbp2 80912 0
loop 80652 0
joydev 76544 0
psmouse 106908 0
dcdbas 73648 0
serio_raw 71428 0
arc4 67584 2
snd_pcsp 76028 0
ecb 68608 2
i2c_i801 75292 0
rng_core 70280 0
iTCO_wdt 78032 0
btusb 77976 0
rfkill 77504 2 iwl3945
evdev 76304 10
mac80211 221616 1 iwl3945
snd_hda_intel 553796 9
led_class 70280 1 iwl3945
bluetooth 120740 3 rfcomm,l2cap,btusb
snd_pcm 144264 8
snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_pcsp,snd_hda_intel
snd_timer 87824 4 snd_seq,snd_pcm
intelfb 100136 0
snd 125432 24
snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_seq,snd_seq_device,snd_pcsp,snd_hda_intel,snd_pcm,snd_timer
soundcore 73488 1 snd
i2c_algo_bit 71684 1 intelfb
cfg80211 97440 2 iwl3945,mac80211
snd_page_alloc 75280 5
snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm
i2c_core 90528 3 i2c_i801,intelfb,i2c_algo_bit
intel_agp 93936 1
wmi 73280 0
button 72992 0
battery 78088 0
video 86036 0
output 68992 1 video
ac 70664 0
xfs 540656 6
dm_mirror 79488 0
dm_region_hash 78208 1 dm_mirror
dm_log 75524 2 dm_mirror,dm_region_hash
dm_snapshot 81992 0
dm_mod 121184 21 dm_mirror,dm_log,dm_snapshot
usbhid 98864 0
hid 107152 1 usbhid
sg 94928 0
sr_mod 80948 1
cdrom 99112 1 sr_mod
sd_mod 97576 4
crc_t10dif 67712 1 sd_mod
ata_piix 88836 4
ata_generic 71556 0
libata 237504 2 ata_piix,ata_generic
scsi_mod 229160 5 firewire_sbp2,sg,sr_mod,sd_mod,libata
ide_pci_generic 70148 0
sdhci_pci 73472 0
sdhci 81924 1 sdhci_pci
mmc_core 117568 1 sdhci
ide_core 178284 1 ide_pci_generic
b44 93968 0
ssb 105604 1 b44
ricoh_mmc 69760 0
pcmcia 101016 1 ssb
pcmcia_core 101924 2 ssb,pcmcia
mii 71168 1 b44
firewire_ohci 88708 0
firewire_core 104256 2 firewire_sbp2,firewire_ohci
crc_itu_t 67840 2 udf,firewire_core
ehci_hcd 99852 0
uhci_hcd 87968 0
thermal 84384 0
processor 111544 4 acpi_cpufreq,thermal
fan 70920 0
thermal_sys 78656 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML
and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS,
943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-if
00 [VGA controller])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at eff00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at eff8 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at efec0000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel modules: intelfb
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME,
943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at eff80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at efebc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Memory behind bridge: efd00000-efdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: efa00000-efcfffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at bf80 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at bf60 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at bf40 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at bf20 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: ef900000-ef9fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge [8086:27b9] (rev 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-rng, iTCO_wdt
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA
IDE Controller [8086:27c4] (rev 01) (prog-if 80 [Master])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at bfa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_generic, ata_piix, ide-pci-generic
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller
[8086:27da] (rev 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 10c0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX
[14e4:170c] (rev 02)
Subsystem: Dell Inspiron 6400 [1028:01af]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 17
Region 0: Memory at ef9fe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: b44
Kernel modules: b44
03:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller
[1180:0832] (prog-if 10 [OHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ef9fd800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
03:01.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro
Host Adapter [1180:0822] (rev 19) (prog-if 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 18
Region 0: Memory at ef9fd400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
03:01.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller
[1180:0843] (rev 0a)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at ef9fd500 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
03:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter [1180:0592] (rev 05)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at ef9fd600 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
03:01.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller
[1180:0852] (rev ff) (prog-if ff)
!!! Unknown header type 7f
0b:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG
[Golan] Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation Device [8086:1021]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4349
Region 0: Memory at efdff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: iwl3945
Kernel modules: iwl3945
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.28-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.28-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93 tools for generating an initramfs
ii module-init-tools 3.7-pre5-1 tools for managing Linux kernel mo
linux-image-2.6.28-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.28-1-amd64 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.28 <none> (no description available)
-- debconf information excluded
--- End Message ---
signature.asc
