Package: linux-image-2.6.26-2-686
Version: 2.6.26-15
Severity: grave
Justification: renders package unusable
Boot process hangs most of the times with the message 'Loading kernel
modules...'.
It happens when booting with command
/boot/vmlinuz-2.6.26-2-686 root=/dev/sda4 ro vga=791 quiet
It *never* happens when "quiet" is turned off! Maybe a timing issue?
The problem was also there with the 2.6.26-1-686 kernel.
It seems that the problem started after the kernel upgrade around 2009-03-21.
The box is a HP Pavilion a1619.dk with a ASUS A8M2N-LA (NodusM3-GL8E)
motherboard and a AMD Athlon 64 3500+ processor.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-15) (da...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu Mar 26 01:08:11 UTC
2009
** Command line:
root=/dev/sda4 ro vga=791
** Not tainted
** Kernel log:
[ 5.114152] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 5.129659] NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
[ 5.139850] NFORCE-MCP51: IDE controller (0x10de:0x0265 rev 0xa1) at PCI
slot 0000:00:0d.0
[ 5.151851] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 5.163499] ide0: BM-DMA at 0xf400-0xf407
[ 5.175144] ide1: BM-DMA at 0xf408-0xf40f
[ 5.186736] Probing IDE interface ide0...
[ 5.197985] usb 1-2.3: new low speed USB device using ohci_hcd and address 3
[ 5.267132] Driver 'sd' needs updating - please use bus_type methods
[ 5.279572] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 5.296011] sd 0:0:0:0: [sda] Write Protect is off
[ 5.306840] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.312011] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 5.327856] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 5.342000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.353945] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.360013] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 5.372045] sda:<6>usb 1-2.3: configuration #1 chosen from 1 choice
[ 5.391339] sda1 sda2 sda3 <<6>usb 1-2.3: New USB device found,
idVendor=04b3, idProduct=3018
[ 5.404033] usb 1-2.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 5.416410] usb 1-2.3: Product: IBM USB Keyboard with UltraNav
[ 5.428824] usb 1-2.3: Manufacturer: Lite-On Tech
[ 5.441124] sda5 sda6 > sda4
[ 5.459405] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.490310] Initializing USB Mass Storage driver...
[ 5.516409] scsi4 : SCSI emulation for USB Mass Storage devices
[ 5.529731] usb-storage: device found at 3
[ 5.529734] usb-storage: waiting for device to settle before scanning
[ 5.670050] usb 1-2.4: new low speed USB device using ohci_hcd and address 4
[ 5.780066] Probing IDE interface ide1...
[ 5.811025] usb 1-2.4: configuration #1 chosen from 1 choice
[ 5.832009] usb 1-2.4: New USB device found, idVendor=06cb, idProduct=0009
[ 5.844029] usb 1-2.4: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 5.856313] usb 1-2.4: Product: Composite TouchPad / TrackPoint
[ 5.868439] usb 1-2.4: Manufacturer: Synaptics Inc.
[ 5.888756] usbcore: registered new interface driver usb-storage
[ 5.901132] USB Mass Storage support registered.
[ 5.913439] usbcore: registered new interface driver hiddev
[ 5.934642] input: Lite-On Tech IBM USB Keyboard with UltraNav as
/class/input/input0
[ 5.960373] input,hidraw0: USB HID v1.10 Keyboard [Lite-On Tech IBM USB
Keyboard with UltraNav] on usb-0000:00:0b.0-2.3
[ 5.986165] input: Lite-On Tech IBM USB Keyboard with UltraNav as
/class/input/input1
[ 6.003305] input,hidraw1: USB HID v1.10 Device [Lite-On Tech IBM USB
Keyboard with UltraNav] on usb-0000:00:0b.0-2.3
[ 6.020016] input: Synaptics Inc. Composite TouchPad / TrackPoint as
/class/input/input2
[ 6.033995] input,hidraw2: USB HID v1.00 Mouse [Synaptics Inc. Composite
TouchPad / TrackPoint] on usb-0000:00:0b.0-2.4
[ 6.055987] input: Synaptics Inc. Composite TouchPad / TrackPoint as
/class/input/input3
[ 6.067640] input,hidraw3: USB HID v1.00 Mouse [Synaptics Inc. Composite
TouchPad / TrackPoint] on usb-0000:00:0b.0-2.4
[ 6.083457] usbcore: registered new interface driver usbhid
[ 6.098143] usbhid: v2.6:USB HID core driver
[ 6.384133] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000fdbf34]
[ 6.568123] hdc: TSSTcorpCD/DVDW TS-H652L, ATAPI CD/DVD-ROM drive
[ 7.252059] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 7.252346] hdc: UDMA/33 mode selected
[ 7.267109] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 7.282691] ide1 at 0x170-0x177,0x376 on irq 15
[ 7.344829] hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 7.361275] Uniform CD-ROM driver Revision: 3.20
[ 7.560728] PM: Starting manual resume from disk
[ 7.648016] kjournald starting. Commit interval 5 seconds
[ 7.668861] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.092124] udevd version 125 started
[ 10.528180] usb-storage: device scan complete
[ 10.534663] scsi 4:0:0:0: Direct-Access Generic- Compact Flash 1.00
PQ: 0 ANSI: 0 CCS
[ 10.568009] scsi 4:0:0:1: Direct-Access Generic- SM/xD-Picture 1.00
PQ: 0 ANSI: 0 CCS
[ 10.588009] scsi 4:0:0:2: Direct-Access Generic- SD/MMC 1.00
PQ: 0 ANSI: 0 CCS
[ 10.610085] scsi 4:0:0:3: Direct-Access Generic- MS/MS-Pro 1.00
PQ: 0 ANSI: 0 CCS
[ 10.628009] input: Power Button (FF) as /class/input/input4
[ 10.664091] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 10.751026] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[ 10.817550] ACPI: Power Button (FF) [PWRF]
[ 10.830981] input: Power Button (CM) as /class/input/input5
[ 10.859665] sd 4:0:0:2: [sdd] Attached SCSI removable disk
[ 10.931633] sd 4:0:0:3: [sde] Attached SCSI removable disk
[ 11.044106] ACPI: Power Button (CM) [PWRB]
[ 11.356080] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
[ 11.369347] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
[ 11.744964] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
[ 11.757988] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI 22
(level, low) -> IRQ 22
[ 11.770976] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 11.874103] input: PC Speaker as /class/input/input6
[ 11.892009] hda_codec: Unknown model for ALC883, trying auto-probe from
BIOS...
[ 13.376720] Adding 2650652k swap on /dev/sda6. Priority:-1 extents:1
across:2650652k
[ 278.538618] EXT3 FS on sda4, internal journal
[ 278.740348] loop: module loaded
[ 278.946535] kjournald starting. Commit interval 5 seconds
[ 278.973135] EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
[ 278.985380] EXT3 FS on sda2, internal journal
[ 278.997398] EXT3-fs: mounted filesystem with ordered data mode.
[ 279.064382] FAT: utf8 is not a recommended IO charset for FAT filesystems,
filesystem will be case sensitive!
[ 281.581841] NET: Registered protocol family 10
[ 281.582267] lo: Disabled Privacy Extensions
[ 281.779576] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+
processors (1 cpu cores) (version 2.20.00)
[ 281.779576] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x6
[ 281.779576] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x8
[ 281.779576] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa
[ 281.779576] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
[ 283.836032] Clocksource tsc unstable (delta = -244351700 ns)
[ 289.040632] lp: driver loaded but no devices found
[ 289.157855] ppdev: user-space parallel port driver
[ 291.904210] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 292.220019] eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
ppdev 6500 0
parport_pc 22500 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
cifs 208692 1
powernow_k8 12036 0
cpufreq_userspace 3172 0
cpufreq_conservative 5960 0
cpufreq_stats 3776 0
cpufreq_ondemand 6476 1
freq_table 4224 3 powernow_k8,cpufreq_stats,cpufreq_ondemand
cpufreq_powersave 1856 0
ipv6 235364 44
nls_utf8 1760 2
nls_cp437 5568 1
vfat 9184 1
fat 40896 1 vfat
nls_base 6820 5 cifs,nls_utf8,nls_cp437,vfat,fat
sbp2 18572 0
loop 12748 0
pcspkr 2432 0
psmouse 32336 0
serio_raw 4740 0
k8temp 4064 0
snd_hda_intel 325688 1
snd_pcm 62596 1 snd_hda_intel
snd_seq 41456 0
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 1 snd_seq
snd 45604 7
snd_hda_intel,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
i2c_nforce2 5536 0
i2c_core 19828 1 i2c_nforce2
button 6096 0
evdev 8000 4
ext3 105512 2
jbd 39444 1 ext3
mbcache 7108 1 ext3
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
usb_storage 77024 0
sd_mod 22200 5
amd74xx 7720 0 [permanent]
ide_pci_generic 3908 0 [permanent]
ide_core 96136 3 ide_cd_mod,amd74xx,ide_pci_generic
ata_generic 4676 0
sata_nv 19240 4
ohci1394 24944 0
libata 140416 2 ata_generic,sata_nv
ieee1394 75800 2 sbp2,ohci1394
ohci_hcd 18500 0
ehci_hcd 28396 0
forcedeth 45072 0
scsi_mod 129324 4 sbp2,usb_storage,sd_mod,libata
dock 8304 1 libata
usbcore 118224 5 usbhid,usb_storage,ohci_hcd,ehci_hcd
thermal 15228 0
processor 32544 2 powernow_k8,thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02f0] (rev
a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:00.1 RAM memory [0500]: nVidia Corporation C51 Memory Controller 0
[10de:02fa] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR+ <PERR- INTx-
00:00.2 RAM memory [0500]: nVidia Corporation C51 Memory Controller 1
[10de:02fe] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory [0500]: nVidia Corporation C51 Memory Controller 5
[10de:02f8] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.4 RAM memory [0500]: nVidia Corporation C51 Memory Controller 4
[10de:02f9] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.5 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02ff] (rev
a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:00.6 RAM memory [0500]: nVidia Corporation C51 Memory Controller 3
[10de:027f] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.7 RAM memory [0500]: nVidia Corporation C51 Memory Controller 2
[10de:027e] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:02.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge
[10de:02fc] (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:04.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge
[10de:02fb] (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fda00000-fdafffff
Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:05.0 VGA compatible controller [0300]: nVidia Corporation C51 [GeForce 6150
LE] [10de:0241] (rev a2) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: nvidiafb
00:09.0 RAM memory [0500]: nVidia Corporation MCP51 Host Bridge [10de:0270]
(rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260] (rev
a3)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:0a.1 SMBus [0c05]: nVidia Corporation MCP51 SMBus [10de:0264] (rev a3)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 4: I/O ports at 4c00 [size=64]
Region 5: I/O ports at 4c40 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:0a.2 RAM memory [0500]: nVidia Corporation MCP51 Memory Controller 0
[10de:0272] (rev a3)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:0b.0 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller
[10de:026d] (rev a3) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0b.1 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller
[10de:026e] (rev a3) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:0d.0 IDE interface [0101]: nVidia Corporation MCP51 IDE [10de:0265] (rev a1)
(prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f400 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
Kernel modules: amd74xx
00:0e.0 IDE interface [0101]: nVidia Corporation MCP51 Serial ATA Controller
[10de:0266] (rev a1) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at e000 [size=16]
Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:0f.0 IDE interface [0101]: nVidia Corporation MCP51 Serial ATA Controller
[10de:0267] (rev a1) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at cc00 [size=16]
Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:10.0 PCI bridge [0604]: nVidia Corporation MCP51 PCI Bridge [10de:026f] (rev
a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=128
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: fdc00000-fdcfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:10.1 Audio device [0403]: nVidia Corporation MCP51 High Definition Audio
[10de:026c] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at fe024000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:14.0 Bridge [0680]: nVidia Corporation MCP51 Ethernet Controller [10de:0269]
(rev a3)
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at c800 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp
03:05.0 FireWire (IEEE 1394) [0c00]: Agere Systems FW323 [11c1:5811] (rev 70)
(prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:2a34]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fddff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
-- System Information:
Debian Release: 5.0.1
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/1 CPU core)
Locale: LANG=en_DK.UTF-8, LC_CTYPE=en_DK.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
