--- Begin Message ---
Package: linux-image-2.6.25-2-amd64
Version: 2.6.25-6
Severity: normal
Although my architecture is different(AMD/MCP51), I am experiencing exactly the
problem described in #482153.
My broadcom device is
03:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01)
After hibernate, I receive the following message. Unloading b43 results in a
hard lock-up.
Reboot seems to be the only way to re-enable the wireless card.
b43-phy0 ERROR: Microcode not responding
As shown below, my firmware is the latest (4.150.10.5)
[ 11.484587] b43-phy0: Broadcom 4311 WLAN found
[ 38.422374] input: b43-phy0 as /class/input/input10
[ 38.829277] b43-phy0: Loading firmware version 410.2160 (2007-05-26
15:32:10)
[ 40.021541] Registered led device: b43-phy0::tx
[ 40.021596] Registered led device: b43-phy0::rx
[ 40.021639] Registered led device: b43-phy0::radio
Prior to 2.6.25 an RTC bug prevented any kind of hibernate stability on my
hardware (dv9000z), so there are
not many options for other AMD/HP Pavillion 9000z users.
Suspend S3 works great every time.
cheers,
iMac
-- Package-specific info:
** Version:
Linux version 2.6.25-2-amd64 (Debian 2.6.25-6) (m...@debian.org) (gcc version
4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Fri Jun 27 00:16:12 UTC
2008
** Command line:
root=/dev/md0 resume=/dev/sdb6 ro
** Tainted: P (1)
** Kernel log:
[ 10.451590] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[ 10.451667] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[ 10.483734] Bluetooth: HCI USB driver ver 2.9
[ 10.485921] usbcore: registered new interface driver hci_usb
[ 10.747716] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 10.747784] ricoh-mmc: Copyright(c) Philip Langdale
[ 10.747874] ricoh-mmc: Ricoh MMC controller found at 0000:07:05.2
[1180:0843] (rev 1)
[ 10.747958] ricoh-mmc: Controller is now disabled.
[ 10.923815] input: PC Speaker as /class/input/input8
[ 10.973790] sdhci: Secure Digital Host Controller Interface driver
[ 10.973850] sdhci: Copyright(c) Pierre Ossman
[ 10.973936] sdhci: SDHCI controller found at 0000:07:05.1 [1180:0822] (rev
19)
[ 10.974378] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7
[ 10.974443] ACPI: PCI Interrupt 0000:07:05.1[B] -> Link [LNK2] -> GSI 7
(level, high) -> IRQ 7
[ 10.974598] sdhc0:slot0: Will use DMA mode even though HW doesn't fully
claim to support it.
[ 10.974712] mmc0: SDHCI at 0xc8000800 irq 7 DMA
[ 11.083530] Linux video capture interface: v2.00
[ 11.253502] usbcam: registering driver r5u870 0.11.1SVN
[ 11.253586] r5u870-0: Detected HP Pavilion Webcam (UVC)
[ 11.413523] r5u870-0: registered as video0
[ 11.413605] usbcore: registered new interface driver r5u870
[ 11.484587] b43-phy0: Broadcom 4311 WLAN found
[ 11.576900] phy0: Selected rate control algorithm 'pid'
[ 11.768396] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[ 11.836149] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps:
0xa04713/0x200000
[ 11.867418] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[ 11.867486] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 21
(level, high) -> IRQ 21
[ 11.867710] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 11.899970] input: SynPS/2 Synaptics TouchPad as /class/input/input9
[ 14.043078] Adding 2104472k swap on /dev/sdb6. Priority:-1 extents:1
across:2104472k
[ 14.787894] EXT3 FS on md0, internal journal
[ 15.143349] loop: module loaded
[ 15.759664] nvidia: module license 'NVIDIA' taints kernel.
[ 15.794952] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 16
[ 15.795021] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LK1E] -> GSI 16
(level, high) -> IRQ 16
[ 15.795166] PCI: Setting latency timer of device 0000:05:00.0 to 64
[ 15.795345] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 173.14.09 Wed
Jun 4 23:40:50 PDT 2008
[ 15.869372] ieee80211_crypt: registered algorithm 'NULL'
[ 15.881207] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 15.881277] ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketr...@linux.intel.com>
[ 16.103712] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology
TL-60 processors (2 cpu cores) (version 2.20.00)
[ 16.235812] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x13
[ 16.235854] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x15
[ 16.235915] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x17
[ 16.235977] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e
[ 17.686031] fuse init (API version 7.9)
[ 20.914948] RPC: Registered udp transport module.
[ 20.915015] RPC: Registered tcp transport module.
[ 28.597261] warning: `avahi-daemon' uses 32-bit capabilities (legacy support
in use)
[ 28.764344] NET: Registered protocol family 10
[ 28.765357] lo: Disabled Privacy Extensions
[ 31.516810] Clocksource tsc unstable (delta = -71904674 ns)
[ 31.549372] pnp: the driver 'parport_pc' has been registered
[ 31.549684] lp: driver loaded but no devices found
[ 31.682359] ppdev: user-space parallel port driver
[ 33.642193] Bridge firewalling registered
[ 33.645177] vnet0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 33.797576] vnet0: starting userspace STP failed, starting kernel STP
[ 33.922116] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 34.349837] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 38.422374] input: b43-phy0 as /class/input/input10
[ 38.713488] Bluetooth: L2CAP ver 2.9
[ 38.713518] Bluetooth: L2CAP socket layer initialized
[ 38.666105] Bluetooth: RFCOMM socket layer initialized
[ 38.666146] Bluetooth: RFCOMM TTY layer initialized
[ 38.666172] Bluetooth: RFCOMM ver 1.8
[ 38.829277] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[ 40.021541] Registered led device: b43-phy0::tx
[ 40.021596] Registered led device: b43-phy0::rx
[ 40.021639] Registered led device: b43-phy0::radio
[ 40.081773] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 40.041839] eth0: no link during initialization.
[ 40.042500] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 44.021591] vnet0: no IPv6 routers present
[ 70.319434] CPU0 attaching NULL sched-domain.
[ 70.319442] CPU1 attaching NULL sched-domain.
[ 70.355343] CPU0 attaching sched-domain:
[ 70.355350] domain 0: span 00000003
[ 70.355352] groups: 00000001 00000002
[ 70.355356] domain 1: span 00000003
[ 70.355358] groups: 00000003
[ 70.355360] domain 2: span 00000003
[ 70.355362] groups: 00000003
[ 70.355364] CPU1 attaching sched-domain:
[ 70.355366] domain 0: span 00000003
[ 70.355368] groups: 00000002 00000001
[ 70.355371] domain 1: span 00000003
[ 70.355372] groups: 00000003
[ 70.355378] domain 2: span 00000003
[ 70.355382] groups: 00000003
[ 78.639952] wlan0: Initial auth_alg=0
[ 78.639961] wlan0: authenticate with AP 00:01:46:03:ed:56
[ 78.640667] wlan0: RX authentication from 00:01:46:03:ed:56 (alg=0
transaction=2 status=0)
[ 78.640674] wlan0: authenticated
[ 78.640677] wlan0: associate with AP 00:01:46:03:ed:56
[ 78.644011] wlan0: RX AssocResp from 00:01:46:03:ed:56 (capab=0x431 status=0
aid=3)
[ 78.644017] wlan0: associated
[ 78.644021] wlan0: switched to short barker preamble
(BSSID=00:01:46:03:ed:56)
[ 78.644656] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 95.660819] wlan0: no IPv6 routers present
** Loaded modules:
Module Size Used by
binfmt_misc 17164 1
rfcomm 46112 0
l2cap 29696 5 rfcomm
rfkill_input 9856 0
ipt_MASQUERADE 8448 1
iptable_nat 12048 1
nf_nat 25624 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 23696 4 iptable_nat,nf_nat
xt_state 7040 1
nf_conntrack 76304 5
ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4,xt_state
ipt_REJECT 8576 2
xt_tcpudp 7936 4
iptable_filter 8192 1
ip_tables 25488 2 iptable_nat,iptable_filter
x_tables 28168 6
ipt_MASQUERADE,iptable_nat,xt_state,ipt_REJECT,xt_tcpudp,ip_tables
bridge 61352 0
ppdev 13832 0
parport_pc 34344 0
lp 17540 0
parport 44848 3 ppdev,parport_pc,lp
ipv6 294120 28
cpufreq_stats 10528 0
nfs 261232 0
lockd 73904 1 nfs
nfs_acl 8192 1 nfs
sunrpc 206984 6 nfs,lockd,nfs_acl
fuse 53440 1
kvm_amd 22804 0
kvm 113368 1 kvm_amd
eeprom 12560 0
cpufreq_userspace 9092 0
cpufreq_conservative 13320 0
cpufreq_ondemand 13712 1
cpufreq_powersave 6272 0
powernow_k8 19076 1
freq_table 9728 3 cpufreq_stats,cpufreq_ondemand,powernow_k8
ieee80211softmac 34304 0
ieee80211 38088 1 ieee80211softmac
ieee80211_crypt 11012 1 ieee80211
nvidia 8114064 36
firewire_sbp2 22808 0
loop 23044 0
joydev 17664 0
snd_hda_intel 414296 1
arc4 6528 2
snd_pcm_oss 46752 0
ecb 8192 2
crypto_blkcipher 24324 1 ecb
snd_pcm 88072 2 snd_hda_intel,snd_pcm_oss
snd_mixer_oss 21376 1 snd_pcm_oss
snd_seq_dummy 8580 0
snd_seq_oss 36736 0
b43 150440 0
snd_seq_midi 13376 0
snd_rawmidi 31008 1 snd_seq_midi
snd_seq_midi_event 12544 2 snd_seq_oss,snd_seq_midi
rfkill 12832 3 rfkill_input,b43
snd_seq 58912 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
r5u870 31944 0
usbcam 53760 1 r5u870
snd_timer 29328 2 snd_pcm,snd_seq
snd_seq_device 12948 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
compat_ioctl32 13184 1 usbcam
mac80211 143244 1 b43
videodev 38528 2 usbcam,compat_ioctl32
psmouse 45724 0
snd 66888 11
snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
sdhci 22796 0
v4l1_compat 16516 1 videodev
videobuf_dma_sg 19076 1 usbcam
mmc_core 56416 1 sdhci
cfg80211 25360 1 mac80211
serio_raw 11652 0
k8temp 10624 0
pcspkr 7808 0
rng_core 9864 1 b43
soundcore 13088 1 snd
ricoh_mmc 8960 0
videobuf_core 24580 2 usbcam,videobuf_dma_sg
snd_page_alloc 15120 2 snd_hda_intel,snd_pcm
hci_usb 21148 2
i2c_nforce2 11904 0
bluetooth 65444 7 rfcomm,l2cap,hci_usb
input_polldev 9872 1 b43
i2c_core 30752 3 eeprom,nvidia,i2c_nforce2
led_class 10248 1 b43
video 27412 21
output 8704 1 video
wmi 13120 0
battery 14208 0
ac 9344 0
button 13856 0
evdev 17408 9
ext3 139408 1
jbd 55336 1 ext3
mbcache 13956 1 ext3
dm_mirror 31748 0
dm_snapshot 22472 0
dm_mod 68536 2 dm_mirror,dm_snapshot
raid1 28032 1
md_mod 87204 2 raid1
ide_cd_mod 41504 0
cdrom 39464 1 ide_cd_mod
sd_mod 33728 5
ide_pci_generic 9476 0 [permanent]
amd74xx 13576 0 [permanent]
ide_core 138160 3 ide_cd_mod,ide_pci_generic,amd74xx
sata_nv 32520 3
ata_generic 13572 0
forcedeth 55820 0
libata 166064 2 sata_nv,ata_generic
scsi_mod 170488 3 firewire_sbp2,sd_mod,libata
dock 16288 1 libata
firewire_ohci 27908 0
firewire_core 45920 2 firewire_sbp2,firewire_ohci
crc_itu_t 6656 1 firewire_core
ehci_hcd 40076 0
ssb 39684 1 b43
ohci_hcd 28292 0
pcmcia 45080 2 b43,ssb
pcmcia_core 46500 2 b43,pcmcia
firmware_class 14976 3 b43,r5u870,pcmcia
thermal 26656 0
processor 49388 4 powernow_k8,thermal
fan 10760 0
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02f7] (rev
a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=3 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 800MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz+ 300MHz+ 400MHz+ 500MHz+
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:00.1 RAM memory [0500]: nVidia Corporation C51 Memory Controller 0
[10de:02fa] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.2 RAM memory [0500]: nVidia Corporation C51 Memory Controller 1
[10de:02fe] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory [0500]: nVidia Corporation C51 Memory Controller 5
[10de:02f8] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.4 RAM memory [0500]: nVidia Corporation C51 Memory Controller 4
[10de:02f9] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.5 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02ff] (rev
a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] #00 [00fe]
Capabilities: [fc] #00 [0000]
00:00.6 RAM memory [0500]: nVidia Corporation C51 Memory Controller 3
[10de:027f] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.7 RAM memory [0500]: nVidia Corporation C51 Memory Controller 2
[10de:027e] (rev a2)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:02.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge
[10de:02fc] (rev a1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: c2000000-c3ffffff
Prefetchable memory behind bridge: 00000000c8200000-00000000c83fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable+
Address: 00000000fee0300c Data: 4149
Capabilities: [60] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt+ MRL- PresDet- CmdCplt- HPIrq+
LinkChg+
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:03.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge
[10de:02fd] (rev a1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: c4000000-c5ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable+
Address: 00000000fee0300c Data: 4151
Capabilities: [60] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn+ PwrFlt+ MRL- PresDet- CmdCplt- HPIrq+
LinkChg+
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:04.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge
[10de:02fb] (rev a1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: c6000000-c7ffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable+
Address: 00000000fee0300c Data: 4159
Capabilities: [60] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:09.0 RAM memory [0500]: nVidia Corporation MCP51 Host Bridge [10de:0270]
(rev a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=9 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz-
600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260] (rev
a3)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: I/O ports at 1d00 [size=128]
00:0a.1 SMBus [0c05]: nVidia Corporation MCP51 SMBus [10de:0264] (rev a3)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 3040 [size=64]
Region 5: I/O ports at 3000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:0a.3 Co-processor [0b40]: nVidia Corporation MCP51 PMU [10de:0271] (rev a3)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 10
Region 0: Memory at c0040000 (32-bit, non-prefetchable) [size=256K]
00:0b.0 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller
[10de:026d] (rev a3) (prog-if 10)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at c0004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0b.1 USB Controller [0c03]: nVidia Corporation MCP51 USB Controller
[10de:026e] (rev a3) (prog-if 20)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at c0005000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0098
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:0d.0 IDE interface [0101]: nVidia Corporation MCP51 IDE [10de:0265] (rev f1)
(prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at 3080 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: AMD_IDE
Kernel modules: ata_generic, amd74xx, ide-pci-generic
00:0e.0 IDE interface [0101]: nVidia Corporation MCP51 Serial ATA Controller
[10de:0266] (rev f1) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 30c0 [size=8]
Region 1: I/O ports at 30b4 [size=4]
Region 2: I/O ports at 30b8 [size=8]
Region 3: I/O ports at 30b0 [size=4]
Region 4: I/O ports at 3090 [size=16]
Region 5: Memory at c0006000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+
Kernel driver in use: sata_nv
Kernel modules: ata_generic, sata_nv, ide-pci-generic
00:0f.0 IDE interface [0101]: nVidia Corporation MCP51 Serial ATA Controller
[10de:0267] (rev f1) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 30d8 [size=8]
Region 1: I/O ports at 30cc [size=4]
Region 2: I/O ports at 30d0 [size=8]
Region 3: I/O ports at 30c8 [size=4]
Region 4: I/O ports at 30a0 [size=16]
Region 5: Memory at c0007000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+
Kernel driver in use: sata_nv
Kernel modules: ata_generic, sata_nv, ide-pci-generic
00:10.0 PCI bridge [0604]: nVidia Corporation MCP51 PCI Bridge [10de:026f] (rev
a2) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=64
Memory behind bridge: c8000000-c80fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: [b8] Subsystem: Gammagraphx, Inc. Device [0000:0000]
Capabilities: [8c] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:10.1 Audio device [0403]: nVidia Corporation MCP51 High Definition Audio
[10de:026c] (rev a2)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:14.0 Bridge [0680]: nVidia Corporation MCP51 Ethernet Controller [10de:0269]
(rev a3)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c0008000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 30e0 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k8temp
Kernel modules: k8temp
03:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11a/b/g
[14e4:4312] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:1360]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c4000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1
unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0
<4us, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [13c] Virtual Channel <?>
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
05:00.0 VGA compatible controller [0300]: nVidia Corporation G70 [GeForce Go
7600] [10de:0398] (rev a1)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c7000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at c6000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at 5000 [size=128]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1
<4us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 128 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Kernel driver in use: nvidia
Kernel modules: nvidiafb, nvidia
07:05.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller
[1180:0832] (prog-if 10)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at c8000000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
07:05.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro
Host Adapter [1180:0822] (rev 19)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 7
Region 0: Memory at c8000800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sdhci
Kernel modules: sdhci
07:05.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller
[1180:0843] (rev 0a)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at c8000c00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
07:05.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter [1180:0592] (rev 05)
Subsystem: Hewlett-Packard Company Device [103c:30b7]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 11
Region 0: Memory at c8001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
07:05.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller
[1180:0852] (rev ff) (prog-if ff)
!!! Unknown header type 7f
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.25-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.25-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92b tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.25-2-amd64 recommends no packages.
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.25-2-amd64/preinst/abort-overwrite-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/prerm/removing-running-kernel-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/old-initrd-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/create-kimage-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/failed-to-move-modules-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/preinst/abort-install-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.25-2-amd64/postinst/depmod-error-2.6.25-2-amd64: false
linux-image-2.6.25-2-amd64/postinst/bootloader-test-error-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/old-system-map-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/prerm/would-invalidate-boot-loader-2.6.25-2-amd64:
true
linux-image-2.6.25-2-amd64/preinst/overwriting-modules-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/depmod-error-initrd-2.6.25-2-amd64: false
linux-image-2.6.25-2-amd64/postinst/old-dir-initrd-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/elilo-initrd-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/bootloader-error-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/preinst/lilo-initrd-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.25-2-amd64/preinst/initrd-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/preinst/bootloader-initrd-2.6.25-2-amd64: true
--- End Message ---
