Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-3
Followup-For: Bug #493479
I'd like to report another machine affected by this regression.
linux-image-2.6.25-2-amd64 2.6.25-7 worked fine for some time.
linux-image-2.6.26-1-amd64 2.6.26-3 locks up after this message:
NET: Registered protocol family 2
Gigabyte GA-MA69VM-S2 motherboard, LE-1620 CPU. See below for
"lspci -vvnn" output. Hope this helps to track down the regression,
likely related to the RS690 chipset (common to both machines: mine
and original submitter's of this bug report).
Marek
00:00.0 Host bridge [0600]: ATI Technologies Inc RS690 Host Bridge [1002:7910]
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge
(Internal gfx) [1002:7912]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fde00000-fdffffff
Prefetchable memory behind bridge: 00000000fa000000-00000000fbffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [b0] Subsystem: ATI Technologies Inc RS690 PCI to PCI
Bridge (Internal gfx) [1002:7912]
Kernel modules: shpchp
00:04.0 PCI bridge [0604]: ATI Technologies Inc Device [1002:7914]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <64ns, L1 <1us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 4, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Address: fee0100c Data: 4149
Capabilities: [b0] Subsystem: Giga-byte Technology Device [1458:5000]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA
[1002:4380] (prog-if 01)
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] SATA HBA <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0)
[1002:4387] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1)
[1002:4388] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2)
[1002:4389] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3)
[1002:438a] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4)
[1002:438b] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI)
[1002:4386] (prog-if 20)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385]
(rev 13)
Subsystem: Giga-byte Technology Device [1458:4385]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 0b00 [size=16]
Region 1: Memory at fed00000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c]
(prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f900 [size=16]
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Kernel driver in use: ATIIXP_IDE
Kernel modules: ata_generic, atiixp, ide-pci-generic
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia [1002:4383]
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge
[1002:438d]
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge
[1002:4384] (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: fda00000-fdafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k8temp
Kernel modules: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS690 [Radeon
X1200 Series] [1002:791e]
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fa000000 (64-bit, prefetchable) [size=32M]
Region 2: Memory at fdff0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at de00 [size=256]
Region 5: Memory at fde00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
03:0f.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)
Subsystem: Giga-byte Technology Device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at ce00 [size=256]
Region 1: Memory at fdbff000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at fda00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: r8169
Kernel modules: r8169
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
