Package: linux-image-2.6.24-etchnhalf.1-amd64
Version: 2.6.24-6~etchnhalf.4
Severity: normal
After installing this package & reboot I still used the previous kernel.
The vmlinuz links were correct, and after doing a manual 'lilo' & reboot
the 2.6.24 kernel booted up. My assumption is that the package installation
does not do a 'lilo' by itself.
-- Package-specific info:
** Version:
Linux version 2.6.24-etchnhalf.1-amd64 (Debian 2.6.24-6~etchnhalf.4) ([EMAIL
PROTECTED]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP
Mon Jul 21 10:36:02 UTC 2008
** Command line:
auto BOOT_IMAGE=Linux ro root=fd01
** Not tainted
** Kernel log:
scsi 2:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
scsi 3:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.5 to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata5: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xc880 irq 19
ata6: SATA max UDMA/133 cmd 0xd000 ctl 0xcc00 bmdma 0xc888 irq 19
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI disk
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdb: sdb1 sdb2
sd 3:0:0:0: [sdb] Attached SCSI disk
Probing IDE interface ide1...
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000ec501c]
md: raid1 personality registered for level 1
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [EMAIL PROTECTED]
Attempting manual resume
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Marking nosave pages: 000000007ff90000 - 0000000100000000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
input: PC Speaker as /class/input/input4
hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
input: ImExPS/2 Generic Explorer Mouse as /class/input/input5
PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
EXT3 FS on dm-1, internal journal
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 3145720k swap on /dev/mapper/vg00-swap. Priority:-1 extents:1
across:3145720k
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
skge eth1: enabling interface
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
skge eth1: Link is up at 100 Mbps, full duplex, flow control both
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
eth1: no IPv6 routers present
pnp: the driver 'parport_pc' has been registered
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
r8169: eth2: link down
ADDRCONF(NETDEV_UP): eth2: link is not ready
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
mtrr: type mismatch for c0000000,4000000 old: write-back new: write-combining
** Loaded modules:
Module Size Used by
nfs 259056 0
nfsd 262312 17
lockd 73520 3 nfs,nfsd
nfs_acl 8320 2 nfs,nfsd
auth_rpcgss 53408 1 nfsd
sunrpc 201736 11 nfs,nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 9600 1 nfsd
appletalk 42768 20
ppdev 13960 0
parport_pc 34984 0
lp 17604 0
parport 45068 3 ppdev,parport_pc,lp
ac 11528 0
battery 20104 0
ipv6 287016 40
ipt_MASQUERADE 8576 1
iptable_nat 12292 1
nf_nat 25900 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 24464 2 iptable_nat
nf_conntrack 78576 4
ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4
ip_tables 25704 1 iptable_nat
x_tables 24968 3 ipt_MASQUERADE,iptable_nat,ip_tables
sbp2 29196 0
loop 23044 0
i2c_i801 14236 0
psmouse 46108 0
i2c_core 30080 1 i2c_i801
serio_raw 12036 0
pcspkr 7936 0
iTCO_wdt 17744 0
snd_hda_intel 362408 0
snd_pcm_oss 46880 0
snd_mixer_oss 21632 1 snd_pcm_oss
snd_pcm 89736 2 snd_hda_intel,snd_pcm_oss
snd_timer 28936 1 snd_pcm
snd 66280 5
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
intel_agp 32544 0
soundcore 13344 1 snd
snd_page_alloc 15504 2 snd_hda_intel,snd_pcm
button 14112 0
evdev 17152 1
ext3 139536 5
jbd 56232 1 ext3
mbcache 14208 1 ext3
dm_mirror 27264 0
dm_snapshot 22216 0
dm_mod 68344 15 dm_mirror,dm_snapshot
raid1 27904 2
md_mod 84764 2 raid1
ide_generic 5632 0 [permanent]
sd_mod 33792 6
ide_cd 44960 0
cdrom 39848 1 ide_cd
ata_piix 25604 4
ata_generic 13188 0
generic 9860 0 [permanent]
ohci1394 37172 0
ahci 34820 0
skge 47504 0
r8169 36996 0
ieee1394 102360 2 sbp2,ohci1394
jmicron 7296 0 [permanent]
ide_core 145432 4 ide_generic,ide_cd,generic,jmicron
libata 164016 3 ata_piix,ata_generic,ahci
scsi_mod 170808 3 sbp2,sd_mod,libata
ehci_hcd 39948 0
uhci_hcd 30368 0
thermal 22944 0
processor 45416 1 thermal
fan 9992 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation P965/G965 Memory Controller Hub
[8086:29a0] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:820b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation P965/G965 PCI Express Root Port
[8086:29a1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: fa800000-fe8fffff
Prefetchable memory behind bridge: 00000000bfe00000-00000000dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:03.0 Communication controller [0780]: Intel Corporation P965/G965 HECI
Controller [8086:29a4] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:820b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at febffc00 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
#4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at dc00 [size=32]
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
#5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at e000 [size=32]
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
#2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ec]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:821a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at febf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 5 [8086:2847] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fe900000-fe9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
#1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d480 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
#2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d800 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
#3 [8086:2832] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d880 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
#1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81ec]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at febff400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface
Controller [8086:2810] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:821a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 4 port
SATA IDE Controller [8086:2820] (rev 02) (prog-if 8f [Master SecP SecO PriP
PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:821a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=16]
Region 5: I/O ports at e080 [size=16]
Capabilities: <access denied>
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller
[8086:283e] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:821a]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 88000000 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00:1f.5 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 2 port
SATA IDE Controller [8086:2825] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:821a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at d400 [size=8]
Region 1: I/O ports at d080 [size=4]
Region 2: I/O ports at d000 [size=8]
Region 3: I/O ports at cc00 [size=4]
Region 4: I/O ports at c880 [size=16]
Region 5: I/O ports at c800 [size=16]
Capabilities: <access denied>
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV44 [GeForce 6200
TurboCache(TM)] [10de:0161] (rev a1) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81f2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: <access denied>
02:00.0 SATA controller [0106]: JMicron Technologies, Inc. JMicron 20360/20363
AHCI Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81e4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at fe9fe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at fe9e0000 [disabled] [size=64K]
Capabilities: <access denied>
02:00.1 IDE interface [0101]: JMicron Technologies, Inc. JMicron 20360/20363
AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81e4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at a880 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at a480 [size=4]
Region 4: I/O ports at a400 [size=16]
Capabilities: <access denied>
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Netgear Unknown device [1385:311a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at feaffc00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at fea00000 [disabled] [size=128K]
Capabilities: <access denied>
04:03.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. IEEE 1394 Host
Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:81fe]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at bc00 [size=128]
Capabilities: <access denied>
04:04.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001
Gigabit Ethernet Controller [11ab:4320] (rev 14)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet
Controller (Asus) [1043:811a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at feaf8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at b400 [size=256]
Expansion ROM at fea20000 [disabled] [size=128K]
Capabilities: <access denied>
-- System Information:
Debian Release: 4.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.24-etchnhalf.1-amd64
Locale: LANG=nl_NL.UTF-8, LC_CTYPE=nl_NL.UTF-8 (charmap=UTF-8)
Versions of packages linux-image-2.6.24-etchnhalf.1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.11etch2 Debian configuration management sy
ii initramfs-tools [linux-initr 0.85i tools for generating an initramfs
ii module-init-tools 3.3-pre4-2 tools for managing Linux kernel mo
linux-image-2.6.24-etchnhalf.1-amd64 recommends no packages.
-- debconf information:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/depmod-error-initrd-2.6.24-etchnhalf.1-amd64:
false
linux-image-2.6.24-etchnhalf.1-amd64/postinst/kimage-is-a-directory:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-etchnhalf.1-amd64/postinst/old-dir-initrd-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.24-etchnhalf.1-amd64/preinst/abort-overwrite-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/preinst/overwriting-modules-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/bootloader-initrd-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/lilo-initrd-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/failed-to-move-modules-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/bootloader-test-error-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/create-kimage-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/postinst/depmod-error-2.6.24-etchnhalf.1-amd64:
false
linux-image-2.6.24-etchnhalf.1-amd64/preinst/abort-install-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/old-initrd-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/initrd-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/preinst/elilo-initrd-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/postinst/bootloader-error-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/old-system-map-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/prerm/removing-running-kernel-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/prerm/would-invalidate-boot-loader-2.6.24-etchnhalf.1-amd64:
true
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
