Package: linux-image-2.6.25-2-amd64
Version: 2.6.25-4
Severity: important
Fails with:
yaird error: bad device link in /sys/class/input/event0/device (fatal)
-- Package-specific info:
** Version:
Linux version 2.6.25-2-amd64 (Debian 2.6.25-3) ([EMAIL PROTECTED]) (gcc version
4.1.3 20080420 (prerelease) (Debian 4.1.2-22)) #1 SMP Wed May 14 14:04:05 UTC
2008
** Command line:
root=/dev/sda2 ro console=tty0
** Not tainted
** Kernel log:
[ 6.433513] sd 0:0:0:0: [sda] 143364060 512-byte hardware sectors (73402 MB)
[ 6.434198] sd 0:0:0:0: [sda] Write Protect is off
[ 6.434389] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 08
[ 6.435354] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[ 6.436368] sd 0:0:0:0: [sda] 143364060 512-byte hardware sectors (73402 MB)
[ 6.436659] sd 0:0:0:0: [sda] Write Protect is off
[ 6.436659] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 08
[ 6.437133] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[ 6.437138] sda: sda1 sda2 sda3 < sda5 >
[ 6.461228] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.385972] kjournald starting. Commit interval 5 seconds
[ 9.385972] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.804289] EXT3 FS on sda2, internal journal
[ 13.502551] Uniform Multi-Platform E-IDE driver
[ 13.502749] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 13.581052] Probing IDE interface ide0...
[ 14.154395] Probing IDE interface ide1...
[ 15.023727] hdc: CD-224E, ATAPI CD/DVD-ROM drive
[ 15.694998] ide1 at 0x170-0x177,0x376 on irq 15
[ 15.695378] hdc: ATAPI 24X CD-ROM drive, 128kB Cache
[ 15.695796] Uniform CD-ROM driver Revision: 3.20
[ 16.273905] md: raid1 personality registered for level 1
[ 16.334751] i2c /dev entries driver
[ 16.412877] ipmi message handler version 39.1
[ 16.435763] IPMI System Interface driver.
[ 16.435968] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o
address 0xca2, slave address 0x20, irq 0
[ 16.565434] ipmi: Found new BMC (man_id: 0x00002a, prod_id: 0x08ff, dev_id:
0x20)
[ 16.565754] IPMI kcs interface initialized
[ 16.704951] nbd: registered device at major 43
[ 16.839913] Copyright (C) 2004 MontaVista Software - IPMI Powerdown via
sys_reboot.
[ 17.171940] IPMI message handler: BMC returned incorrect response, expected
netfn 2d cmd 1, got netfn 2c cmd 1
[ 16.857892] IPMI poweroff: ATCA Detect mfg 0x2A prod 0x8FF
[ 16.858103] IPMI poweroff: Found a chassis style poweroff function
[ 16.879270] ipmi device interface
[ 17.239648] IPMI Watchdog: driver initialized
[ 17.036084] device-mapper: uevent: version 1.0.3
[ 17.047156] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised:
[EMAIL PROTECTED]
[ 22.786877] kjournald starting. Commit interval 5 seconds
[ 22.795656] EXT3 FS on sda1, internal journal
[ 22.795656] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.885789] JFS: nTxBlock = 8192, nTxLock = 65536
[ 23.358680] Adding 1048568k swap on /dev/mapper/root--vg-swap. Priority:1
extents:1 across:1048568k
[ 36.843916] No dock devices found.
[ 36.870134] libata version 3.00 loaded.
[ 35.720518] AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
[ 35.720722] AMD8111: IDE controller (0x1022:0x7469 rev 0x03) at PCI slot
0000:00:07.1
[ 35.721031] AMD8111: not 100% native mode: will probe irqs later
[ 35.721240] AMD8111: port 0x0170 already claimed by ide1
[ 35.721435] ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:PIO,
hdb:PIO
[ 35.721788] Probing IDE interface ide0...
[ 39.240639] AMD768 RNG detected
[ 58.709666] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI)
Driver
[ 57.276937] ACPI: PCI Interrupt 0000:01:00.0[D] -> GSI 19 (level, low) ->
IRQ 19
[ 57.277304] ohci_hcd 0000:01:00.0: OHCI Host Controller
[ 57.288749] ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus
number 1
[ 57.289077] ohci_hcd 0000:01:00.0: irq 19, io mem 0xfd120000
[ 57.355306] usb usb1: configuration #1 chosen from 1 choice
[ 57.362376] hub 1-0:1.0: USB hub found
[ 57.362576] hub 1-0:1.0: 3 ports detected
[ 57.468531] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 57.468750] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 57.469038] usb usb1: Product: OHCI Host Controller
[ 57.469224] usb usb1: Manufacturer: Linux 2.6.25-2-amd64 ohci_hcd
[ 57.469423] usb usb1: SerialNumber: 0000:01:00.0
[ 57.469636] ACPI: PCI Interrupt 0000:01:00.1[D] -> GSI 19 (level, low) ->
IRQ 19
[ 57.469998] ohci_hcd 0000:01:00.1: OHCI Host Controller
[ 57.482085] ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus
number 2
[ 57.482404] ohci_hcd 0000:01:00.1: irq 19, io mem 0xfd121000
[ 57.542761] usb usb2: configuration #1 chosen from 1 choice
[ 57.547358] hub 2-0:1.0: USB hub found
[ 57.547559] hub 2-0:1.0: 3 ports detected
[ 57.656551] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 57.656771] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 57.657059] usb usb2: Product: OHCI Host Controller
[ 57.657244] usb usb2: Manufacturer: Linux 2.6.25-2-amd64 ohci_hcd
[ 57.657444] usb usb2: SerialNumber: 0000:01:00.1
[ 61.571284] tg3.c:v3.91 (April 18, 2008)
[ 61.571487] ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 25 (level, low) ->
IRQ 25
[ 61.623427] eth0: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)]
(PCIX:66MHz:64-bit) 10/100/1000Base-T Ethernet 00:09:3d:12:69:3f
[ 61.623775] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1]
TSOcap[1]
[ 61.624071] eth0: dma_rwctrl[769f0000] dma_mask[64-bit]
[ 61.624291] ACPI: PCI Interrupt 0000:02:02.1[B] -> GSI 26 (level, low) ->
IRQ 26
[ 61.680916] eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)]
(PCIX:66MHz:64-bit) 10/100/1000Base-T Ethernet 00:09:3d:12:69:40
[ 61.681264] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1]
TSOcap[1]
[ 61.681556] eth1: dma_rwctrl[769f0000] dma_mask[64-bit]
[ 69.913844] input: PC Speaker as /class/input/input2
[ 70.186305] Floppy drive(s): fd0 is 1.44M
[ 70.205334] FDC 0 is a post-1991 82077
[ 94.238600] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[ 94.238885] tg3: eth0: Flow control is on for TX and on for RX.
[ 97.215374] NET: Registered protocol family 10
[ 97.216392] lo: Disabled Privacy Extensions
[ 95.898467] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 99.450328] RPC: Registered udp transport module.
[ 99.450328] RPC: Registered tcp transport module.
[ 101.320796] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[ 101.321006] tg3: eth1: Flow control is on for TX and on for RX.
[ 101.326254] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 110.319023] eth0: no IPv6 routers present
[ 114.767149] eth1: no IPv6 routers present
** Loaded modules:
Module Size Used by
nfs 261232 3
lockd 73904 2 nfs
nfs_acl 8192 1 nfs
sunrpc 206984 25 nfs,lockd,nfs_acl
ipv6 294120 49
floppy 66984 0
pcspkr 7808 0
tg3 102532 0
ohci_hcd 28164 0
i2c_amd756 11780 0
amd_rng 7688 0
rng_core 9864 1 amd_rng
amd74xx 13576 0 [permanent]
ide_pci_generic 9476 0 [permanent]
ata_generic 13572 0
libata 165808 1 ata_generic
dock 16288 1 libata
jfs 169296 3
nls_base 13444 1 jfs
dm_snapshot 22472 0
dm_mirror 31748 0
dm_mod 68536 11 dm_snapshot,dm_mirror
ipmi_watchdog 25840 0
ipmi_devintf 15888 0
ipmi_poweroff 14920 0
nbd 17552 0
k8temp 10624 0
ipmi_si 48876 2
ipmi_msghandler 43000 4 ipmi_watchdog,ipmi_devintf,ipmi_poweroff,ipmi_si
i2c_amd8111 10496 0
i2c_dev 12432 0
zlib_deflate 24088 0
raid1 28032 0
md_mod 87204 1 raid1
adm1031 24340 0
adm1025 20244 0
hwmon_vid 7680 1 adm1025
adm1021 19120 0
i2c_core 30752 6
i2c_amd756,i2c_amd8111,i2c_dev,adm1031,adm1025,adm1021
twofish 11392 0
twofish_common 18688 1 twofish
sha512 9728 0
aes_x86_64 12928 0
aes_generic 32424 1 aes_x86_64
sha256_generic 13952 0
blowfish 13184 0
psmouse 45724 0
ide_generic 5760 0 [permanent]
ide_disk 20096 0
ide_cd_mod 41504 0
cdrom 39464 1 ide_cd_mod
ide_core 138160 5
amd74xx,ide_pci_generic,ide_generic,ide_disk,ide_cd_mod
ext3 139280 2
jbd 55336 1 ext3
mbcache 13956 1 ext3
sd_mod 33728 4
mptspi 23952 3
mptscsih 33024 1 mptspi
mptbase 66276 2 mptspi,mptscsih
scsi_transport_spi 32000 1 mptspi
scsi_mod 170360 5 libata,sd_mod,mptspi,mptscsih,scsi_transport_spi
shpchp 38300 0
pci_hotplug 35512 1 shpchp
evdev 17408 0
thermal 26656 0
processor 49388 1 thermal
fan 10760 0
** PCI devices:
00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] AMD-8111 PCI
[1022:7460] (rev 07)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 123
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
Memory behind bridge: fd100000-fe7fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=6 UnitCnt=4 MastHost- DefDir-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0
Link Config 0: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 1.02
Capabilities: [f0] HyperTransport: Interrupt Discovery and Configuration
Kernel modules: shpchp
00:07.0 ISA bridge [0601]: Advanced Micro Devices [AMD] AMD-8111 LPC
[1022:7468] (rev 05)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:07.1 IDE interface [0101]: Advanced Micro Devices [AMD] AMD-8111 IDE
[1022:7469] (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at 1000 [size=16]
Kernel driver in use: AMD_IDE
Kernel modules: ata_generic, ide-pci-generic, amd74xx
00:07.3 Bridge [0680]: Advanced Micro Devices [AMD] AMD-8111 ACPI [1022:746b]
(rev 05)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: amd756_smbus
Kernel modules: amd-rng, i2c-amd756
00:0a.0 PCI bridge [0604]: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge
[1022:7450] (rev 12)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: fe800000-fe8fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=66MHz
Status: Dev=00:0a.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=10 UnitCnt=2 MastHost- DefDir-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0
Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Link Control 1: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 1.02
Kernel modules: shpchp
00:0a.1 PIC [0800]: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC
[1022:7451] (rev 01) (prog-if 10)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fd000000 (64-bit, non-prefetchable) [size=4K]
00:0b.0 PCI bridge [0604]: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge
[1022:7450] (rev 12)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [a0] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=00:0b.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=14 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Kernel modules: shpchp
00:0b.1 PIC [0800]: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC
[1022:7451] (rev 01) (prog-if 10)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fd001000 (64-bit, non-prefetchable) [size=4K]
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
00:19.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
00:19.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:19.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:19.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
01:00.0 USB Controller [0c03]: Advanced Micro Devices [AMD] AMD-8111 USB
[1022:7464] (rev 0b) (prog-if 10)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fd120000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
01:00.1 USB Controller [0c03]: Advanced Micro Devices [AMD] AMD-8111 USB
[1022:7464] (rev 0b) (prog-if 10)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fd121000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
01:05.0 VGA compatible controller [0300]: Trident Microsystems Blade 3D PCI/AGP
[1023:9880] (rev 3a)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe000000 (32-bit, non-prefetchable) [size=8M]
Region 1: Memory at fd100000 (32-bit, non-prefetchable) [size=128K]
Region 2: Memory at fd800000 (32-bit, non-prefetchable) [size=8M]
Capabilities: [80] AGP version 1.0
Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [90] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: tridentfb
02:02.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704
Gigabit Ethernet [14e4:1648] (rev 03)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 25
Region 0: Memory at fe810000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fe800000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=2048 OST=1
Status: Dev=02:02.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data <?>
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
Enable-
Address: 8a04b3a4c4cc064c Data: 0e21
Kernel driver in use: tg3
Kernel modules: tg3
02:02.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704
Gigabit Ethernet [14e4:1648] (rev 03)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 26
Region 0: Memory at fe830000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fe820000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=2048 OST=1
Status: Dev=02:02.1 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data <?>
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
Enable-
Address: 0841464800002404 Data: 0100
Kernel driver in use: tg3
Kernel modules: tg3
02:04.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c1030 PCI-X
Fusion-MPT Dual Ultra320 SCSI [1000:0030] (rev 08)
Subsystem: Newisys, Inc. Device [17c2:0010]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 72 (4250ns min, 4500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at fe850000 (64-bit, non-prefetchable) [size=64K]
Region 3: Memory at fe840000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [68] PCI-X non-bridge device
Command: DPERE- ERO- RBC=2048 OST=4
Status: Dev=02:04.0 64bit+ 133MHz- SCD- USC- DC=simple
DMMRBC=2048 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-
Kernel driver in use: mptspi
Kernel modules: mptspi
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.25-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.ISO-8859-15, LC_CTYPE=en_US.ISO-8859-15 (charmap=ISO-8859-15)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.25-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
ii yaird [linux-initramfs-tool] 0.0.12-25 Yet Another mkInitRD
linux-image-2.6.25-2-amd64 recommends no packages.
-- debconf information:
linux-image-2.6.25-2-amd64/preinst/abort-overwrite-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/create-kimage-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/failed-to-move-modules-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/depmod-error-2.6.25-2-amd64: false
linux-image-2.6.25-2-amd64/postinst/bootloader-test-error-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/prerm/would-invalidate-boot-loader-2.6.25-2-amd64:
true
linux-image-2.6.25-2-amd64/postinst/old-dir-initrd-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.25-2-amd64/preinst/bootloader-initrd-2.6.25-2-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.25-2-amd64/prerm/removing-running-kernel-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/old-initrd-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/abort-install-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.25-2-amd64/postinst/old-system-map-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/overwriting-modules-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/depmod-error-initrd-2.6.25-2-amd64: false
linux-image-2.6.25-2-amd64/preinst/elilo-initrd-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/bootloader-error-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/preinst/lilo-initrd-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/initrd-2.6.25-2-amd64:
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
