Your message dated Tue, 20 May 2008 16:41:23 +0200
with message-id <[EMAIL PROTECTED]>
and subject line Re: Bug#476715: Rép. : Re: Bug#476715: Order detect of Disk
scsi and HBA Fiber Channel (qla2xxx)
has caused the Debian Bug report #476715,
regarding Order detect of Disk scsi and HBA Fiber Channel (qla2xxx)
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [EMAIL PROTECTED]
immediately.)
--
476715: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=476715
Debian Bug Tracking System
Contact [EMAIL PROTECTED] with problems
--- Begin Message ---
Package: linux-image-2.6.18-6-686Version: 2.6.18.dfsg.1-18etch1 Ibm server6
disk in raid51 HBA Fiber Channel (qla2xxx) On the boot of my linux image, 1
times on 3 it works. When it works My local disk is sda $ dmesg ...qla2xxx
0000:04:04.0: Found an ISP2312, irq 201, iobase 0xf8842000
qla2xxx 0000:04:04.0: Configuring PCI space...
qla2xxx 0000:04:04.0: Configure NVRAM parameters...
qla2xxx 0000:04:04.0: Verifying loaded RISC code...
scsi1 : IBM PCI ServeRAID 7.12.05 Build 761
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: Unable to derive IRQ for device 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A]: no GSI
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x0480-0x0487, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
Vendor: IBM Model: SERVERAID Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
Vendor: IBM Model: SERVERAID Rev: 1.00
Type: Processor ANSI SCSI revision: 02
SCSI device sda: 213288960 512-byte hdwr sectors (109204 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI device sda: 213288960 512-byte hdwr sectors (109204 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4 < sda5 sda6<5> Vendor: IBM Model: 40K
sda76480a
S320 0 Rev: 1
Type: Processor ANSI SCSI revision: 02
sda8 >
sd 1:0:0:0: Attached scsi disk sda
qla2xxx 0000:04:04.0: Allocated (412 KB) for firmware dump...
qla2xxx 0000:04:04.0: LIP reset occured (f7f7).
qla2xxx 0000:04:04.0: Waiting for LIP to complete...
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: IBM PPC I/F as /class/input/input1
input: USB HID v1.10 Keyboard [IBM PPC I/F] on usb-0000:00:1d.1-2
input: IBM PPC I/F as /class/input/input2
input: USB HID v1.10 Mouse [IBM PPC I/F] on usb-0000:00:1d.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
hda: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
qla2xxx 0000:04:04.0: LOOP UP detected (2 Gbps).
qla2xxx 0000:04:04.0: Topology - (F_Port), Host Loop address 0xffff
scsi0 : qla2xxx
qla2xxx 0000:04:04.0:
QLogic Fibre Channel HBA Driver: 8.01.07-k1
QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
ISP2312: PCI-X (133 MHz) @ 0000:04:04.0 hdma-, host#=0, fw=3.03.20 IPX
Vendor: IBM Model: 1722-600 Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdb: 1428495360 512-byte hdwr sectors (731390 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
SCSI device sdb: 1428495360 512-byte hdwr sectors (731390 MB)
sdb: Write Protect is off
sdb: Mode Sense: 77 00 10 08
SCSI device sdb: drive cache: write back w/ FUA
sdb:<6>hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sdb1
sd 0:0:0:0: Attached scsi disk sdb
Vendor: IBM Model: Universal Xport Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
Vendor: IBM Model: 1722-600 Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sdc: 1428495360 512-byte hdwr sectors (731390 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write back w/ FUA
SCSI device sdc: 1428495360 512-byte hdwr sectors (731390 MB)
sdc: Write Protect is off
sdc: Mode Sense: 77 00 10 08
SCSI device sdc: drive cache: write back w/ FUA
sdc: sdc1
sd 0:0:1:0: Attached scsi disk sdc
Vendor: IBM Model: Universal Xport Rev: 0520
Type: Direct-Access ANSI SCSI revision: 03
$ lsscsi[0:0:0:1] disk IBM 1722-600 0520 /dev/sdb
[0:0:1:1] disk IBM 1722-600 0520 /dev/sdc
[1:0:0:0] disk IBM SERVERAID 1.00 /dev/sda
[1:0:15:0] process IBM SERVERAID 1.00 -
[1:2:8:0] process IBM 40K6480a S320 0 1 -
When it works not, it stop the following message: Begin: Waiting for root
file system... and my local disk is sdb or sdc It detect the qla2xxx before
the local disk. Thanks
--- End Message ---
--- Begin Message ---
On Tue, 22 Apr 2008, Patrick Mayrand wrote:
> ok it work
>
> i create my swap
>
> swapoff -a
> mkswap -L swap01 /dev/sda1
> swapon -a
>
> and i change /etc/fstab and /boot/grub/menu.lst
>
> proc /proc proc defaults 0 0
> UUID=35871801-411b-4e94-a28d-c954be047faa / ext3
> defaults,errors=remount-ro 0 1
> UUID=13b25069-c286-4b1f-a9d4-679929d9967d /boot ext3
> defaults 0 2
> UUID=673a0f60-9556-4b27-b876-ca76b200cb9e /home ext3
> defaults 0 2
> UUID=28dd8dd8-9dff-43a8-8eca-40f7f645bc7a /tmp ext3
> defaults 0 2
> UUID=d0242fb9-2512-433c-8da8-cade9bfa4887 /usr ext3
> defaults 0 2
> UUID=fdc2fc92-e863-4e23-9ba3-a0687b8f40f1 /var ext3
> defaults 0 2
> UUID=06249203-7921-45b9-9ca7-67e6d12ae01a none swap sw
> 0 0
> /dev/hda /media/cdrom0 udf,iso9660 user,noauto 0 0
> /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0
> UUID=076761cc-c66e-4c34-a997-08882ce986b8 /mnt/EntrepotImageJPG ext3
> rw,user,auto 0 0
>
> Thank you,
>
> Pat
closing report.
--
maks
--- End Message ---
