Package: linux-image-2.6.22-1-k7 Version: 2.6.22-2 Severity: important After upgrading to 2.6.22, my firewire controller just stopped working altogether. It had been working perfectly in all previous versions. I was looking to manually load the old stack/sbp2 modules, but I see you chose not to include them anymore.
I found this message from Stefan Richter that explains things a bit: "The NVidia nForce2 chipset has an own FireWire controller, and that one is only "supported" by a gross hack in ohci1394 and at the moment unsupported in firewire-ohci. There is even a bug report in Red Hat's bugzilla where fw-ohci hung up when trying to initialize an nForce2 chip." See: http://www.ussg.iu.edu/hypermail/linux/kernel/0707.2/3700.html This is a regression for me, and all nforce2 firewire users. I believe it's also one of the reasons Linux 2.6.22 shipped with 2 firewire stacks instead of just the new one: the new one just doesn't cover all cases yet. I therefore respectfully request you re-enable the old stack. Thanks -- Mourad DC -- Package-specific info: ** Version: Linux version 2.6.22-1-k7 (Debian 2.6.22-2) ([EMAIL PROTECTED]) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14)) #1 SMP Mon Jul 23 14:02:09 UTC 2007 ** Tainted: PFSRMB ** Kernel log: PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: irq 18, io mem 0xed083000 ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected NFORCE2: IDE controller at PCI slot 0000:00:09.0 NFORCE2: chipset revision 162 NFORCE2: not 100% native mode: will probe irqs later NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA Probing IDE interface ide0... firewire_core: created new fw device fw0 (0 config rom retries) hda: HL-DT-ST RW/DVD GCC-4520B, ATAPI CD/DVD-ROM drive usb 3-2: new high speed USB device using ehci_hcd and address 3 usb 3-2: configuration #1 chosen from 1 choice hub 3-2:1.0: USB hub found hub 3-2:1.0: 4 ports detected ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 swsusp: Basic memory bitmaps created swsusp: Basic memory bitmaps freed EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. usb 2-1: new low speed USB device using ohci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice usb 2-2: new full speed USB device using ohci_hcd and address 3 usb 2-2: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev usb 1-1: new full speed USB device using ohci_hcd and address 3 usb 1-1: configuration #1 chosen from 1 choice input: Logitech NetPlay Keyboard as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech NetPlay Keyboard] on usb-0000:00:02.1-1 input: Logitech USB Gaming Mouse as /class/input/input1 input: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:02.1-2 hiddev96: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:02.1-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver kjournald starting. Commit interval 5 seconds EXT3-fs: sda1: orphan cleanup on readonly fs ext3_orphan_cleanup: deleting unreferenced inode 2310155 ext3_orphan_cleanup: deleting unreferenced inode 2281718 EXT3-fs: sda1: 2 orphan inodes deleted EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Linux agpgart interface v0.102 (c) Dave Jones agpgart: Detected NVIDIA nForce2 chipset agpgart: AGP aperture is 128M @ 0xe0000000 Real Time Clock Driver v1.12ac i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000 i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5100 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 input: PC Speaker as /class/input/input2 ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) -> IRQ 19 PCI: Setting latency timer of device 0000:00:06.0 to 64 Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: HCI USB driver ver 2.9 intel8x0_measure_ac97_clock: measured 52786 usecs intel8x0: clocking to 48000 usbcore: registered new interface driver hci_usb Adding 2104504k swap on /dev/sda2. Priority:-1 extents:1 across:2104504k EXT3 FS on sda1, internal journal it87: Found IT8712F chip at 0x290, revision 5 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED] fuse init (API version 7.8) NET: Registered protocol family 10 lo: Disabled Privacy Extensions input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] lp: driver loaded but no devices found ppdev: user-space parallel port driver Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 eth0: no IPv6 routers present firewire_core: giving up on config rom for node id ffc0 nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 16 NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:04:00.0 into 8x mode ** Loaded modules: Module Size Used by nvidia 7249460 24 binfmt_misc 11400 1 rfcomm 36824 0 l2cap 23232 5 rfcomm ppdev 8964 0 parport_pc 34212 0 lp 11300 0 parport 34312 3 ppdev,parport_pc,lp button 8208 0 ac 5508 0 battery 10308 0 ipv6 239460 24 nls_iso8859_1 4416 1 cifs 200948 1 fuse 42388 1 dm_crypt 13256 0 dm_snapshot 16868 0 dm_mirror 21312 0 dm_mod 52480 3 dm_crypt,dm_snapshot,dm_mirror it87 18000 0 hwmon_vid 3264 1 it87 i2c_isa 4480 1 it87 hci_usb 16668 2 bluetooth 50148 7 rfcomm,l2cap,hci_usb snd_intel8x0 32412 5 snd_ac97_codec 93220 1 snd_intel8x0 ac97_bus 2560 1 snd_ac97_codec snd_pcm_oss 39904 0 snd_mixer_oss 15872 1 snd_pcm_oss pcspkr 3392 0 shpchp 31380 0 pci_hotplug 29568 1 shpchp snd_pcm 72772 5 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_timer 21380 1 snd_pcm snd 48804 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer soundcore 7840 1 snd snd_page_alloc 9800 2 snd_intel8x0,snd_pcm i2c_nforce2 6144 0 rtc 13144 0 i2c_core 24000 4 nvidia,it87,i2c_isa,i2c_nforce2 nvidia_agp 8732 1 agpgart 32264 2 nvidia,nvidia_agp evdev 9664 4 tsdev 8320 0 usbhid 26144 0 hid 25792 1 usbhid ext3 122632 1 jbd 55784 1 ext3 mbcache 8580 1 ext3 ide_cd 36896 0 cdrom 33184 1 ide_cd amd74xx 13788 0 [permanent] generic 5124 0 [permanent] ide_core 114436 3 ide_cd,amd74xx,generic ehci_hcd 31116 0 firewire_ohci 16896 0 firewire_core 39424 1 firewire_ohci crc_itu_t 2432 1 firewire_core ata_generic 7876 0 ohci_hcd 20036 0 forcedeth 45064 0 usbcore 125704 5 hci_usb,usbhid,ehci_hcd,ohci_hcd sd_mod 27584 3 thermal 13768 0 processor 31368 1 thermal fan 5124 0 sata_sil 11208 2 libata 116848 2 ata_generic,sata_sil scsi_mod 137356 2 sd_mod,libata ** PCI devices: 00:00.0 Host bridge [0600]: nVidia Corporation nForce2 AGP (different version?) [10de:01e0] (rev c1) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M] Capabilities: <access denied> 00:00.1 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 1 [10de:01eb] (rev c1) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.2 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 4 [10de:01ee] (rev c1) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.3 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 3 [10de:01ed] (rev c1) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.4 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 2 [10de:01ec] (rev c1) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.5 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 5 [10de:01ef] (rev c1) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:01.0 ISA bridge [0601]: nVidia Corporation nForce2 ISA Bridge [10de:0060] (rev a4) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: <access denied> 00:01.1 SMBus [0c05]: nVidia Corporation nForce2 SMBus (MCP) [10de:0064] (rev a2) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 255 Region 0: I/O ports at e000 [size=32] Capabilities: <access denied> 00:02.0 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10 [OHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 18 Region 0: Memory at ed087000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> 00:02.1 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10 [OHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 19 Region 0: Memory at ed082000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> 00:02.2 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0068] (rev a4) (prog-if 20 [EHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 18 Region 0: Memory at ed083000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> 00:04.0 Ethernet controller [0200]: nVidia Corporation nForce2 Ethernet Controller [10de:0066] (rev a1) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at ed086000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at e400 [size=8] Capabilities: <access denied> 00:05.0 Multimedia audio controller [0401]: nVidia Corporation nForce Audio Processing Unit [10de:006b] (rev a2) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (250ns min, 3000ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:06.0 Multimedia audio controller [0401]: nVidia Corporation nForce2 AC97 Audio Controler (MCP) [10de:006a] (rev a1) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at d000 [size=256] Region 1: I/O ports at d400 [size=128] Region 2: Memory at ed080000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> 00:08.0 PCI bridge [0604]: nVidia Corporation nForce2 External PCI Bridge [10de:006c] (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=02, sec-latency=32 I/O behind bridge: 0000a000-0000bfff Memory behind bridge: ec000000-ecffffff Prefetchable memory behind bridge: 50000000-500fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- 00:09.0 IDE interface [0101]: nVidia Corporation nForce2 IDE [10de:0065] (rev a2) (prog-if 8a [Master SecP PriP]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at f000 [size=16] Capabilities: <access denied> 00:0d.0 FireWire (IEEE 1394) [0c00]: nVidia Corporation nForce2 FireWire (IEEE 1394) Controller [10de:006e] (rev a3) (prog-if 10 [OHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Unknown device [1297:f541] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at ed084000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at ed085000 (32-bit, non-prefetchable) [size=64] Capabilities: <access denied> 00:1e.0 PCI bridge [0604]: nVidia Corporation nForce2 AGP [10de:01e8] (rev c1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Bus: primary=00, secondary=04, subordinate=04, sec-latency=32 Memory behind bridge: e9000000-ebffffff Prefetchable memory behind bridge: d0000000-dfffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- 01:06.0 PCI bridge [0604]: Hint Corp HB6 Universal PCI-PCI bridge (non-transparent mode) [3388:0021] (rev 15) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size: 32 bytes Bus: primary=01, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000a000-0000bfff Memory behind bridge: ec000000-ecffffff Prefetchable memory behind bridge: 0000000050000000-00000000500fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: <access denied> 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10) Subsystem: AFAVLAB Technology Inc Unknown device [14db:8169] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at a000 [size=256] Region 1: Memory at ec081000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 50080000 [disabled] [size=64K] Capabilities: <access denied> 02:01.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller [1095:3512] (rev 01) Subsystem: Silicon Image, Inc. SiI 3512 SATALink Controller [1095:3512] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at a400 [size=8] Region 1: I/O ports at a800 [size=4] Region 2: I/O ports at ac00 [size=8] Region 3: I/O ports at b000 [size=4] Region 4: I/O ports at b400 [size=16] Region 5: Memory at ec080000 (32-bit, non-prefetchable) [size=512] [virtual] Expansion ROM at 50000000 [disabled] [size=512K] Capabilities: <access denied> 04:00.0 VGA compatible controller [0300]: nVidia Corporation NV43 [GeForce 6600/GeForce 6600 GT] [10de:00f1] (rev a2) (prog-if 00 [VGA]) Subsystem: XFX Pine Group Inc. GeForce 6600 GT AGP 128MB DDR3 DUAL DVI TV [1682:2119] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 248 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 16 Region 0: Memory at e9000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 2: Memory at ea000000 (32-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at eb000000 [disabled] [size=128K] Capabilities: <access denied> -- System Information: Debian Release: lenny/sid APT prefers unstable APT policy: (500, 'unstable'), (1, 'experimental') Architecture: i386 (i686) Kernel: Linux 2.6.22-1-k7 (SMP w/1 CPU core) Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages linux-image-2.6.22-1-k7 depends on: ii initramfs-tools [linux-initr 0.89 tools for generating an initramfs ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo Versions of packages linux-image-2.6.22-1-k7 recommends: ii libc6-i686 2.6-4 GNU C Library: Shared libraries [i -- debconf information excluded -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
