Package: linux-image-2.6.21-1-powerpc Version: 2.6.21-4 Severity: important
Since upgrading to this kernel version any attempt to suspend my laptop has failed. The machine begins to suspend, complains that it cannot suspend and then attempts to abort the suspend but fails to do so, forcing a manual reset. Both aspects of this are a problem - the failure to abort is a more serious issue for me since it can cause data loss. When I have access to something I can use to capture the console output I will provie that, unfortunately I don't have anything right now. The machine is: processor : 0 cpu : 7447A, altivec supported clock : 749.999000MHz revision : 0.1 (pvr 8003 0101) bogomips : 36.73 timebase : 18432000 platform : PowerMac machine : PowerBook5,4 motherboard : PowerBook5,4 MacRISC3 Power Macintosh detected as : 287 (PowerBook G4 15") pmac flags : 0000001b L2 cache : 512K unified pmac-generation : NewWorld -- Package-specific info: ** Version: Linux version 2.6.21-1-powerpc (Debian 2.6.21-4) ([EMAIL PROTECTED]) (gcc version 4.1.3 20070518 (prerelease) (Debian 4.1.2-8)) #1 Sat May 26 14:30:26 CEST 2007 ** Not tainted ** Kernel log: Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0001:10:13.0, mfunc 0x00001002, devctl 0x60 Yenta: ISA IRQ mask 0x0000, PCI irq 53 Socket status: 30000087 pcmcia: parent PCI bridge I/O window: 0x0 - 0x7fffff pcmcia: parent PCI bridge Memory window: 0xf3000000 - 0xf3ffffff pcmcia: parent PCI bridge Memory window: 0x80000000 - 0xafffffff bcm43xx driver PCI: Enabling device 0001:10:12.0 (0004 -> 0006) bcm43xx: Chip ID 0x4306, rev 0x3 bcm43xx: Number of cores: 5 bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243 bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243 bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243 bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243 bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243 bcm43xx: PHY connected bcm43xx: Detected PHY: Analog: 2, Type 2, Revision 2 bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2) bcm43xx: Radio turned off bcm43xx: Radio turned off ieee1394: Initialized config rom entry `ip1394' PCI: Enabling device 0001:10:1b.2 (0004 -> 0006) ehci_hcd 0001:10:1b.2: EHCI Host Controller ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 4 ehci_hcd 0001:10:1b.2: irq 63, io mem 0xa0000000 ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 5 ports detected Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized PowerMac i2c bus pmu 2 registered PowerMac i2c bus pmu 1 registered PowerMac i2c bus mac-io 0 registered PowerMac i2c bus uni-n 1 registered PowerMac i2c bus uni-n 0 registered sungem.c:v0.98 8/24/03 David S. Miller ([EMAIL PROTECTED]) PHY ID: 1410cc1, addr: 0 eth1: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0d:93:c1:97:b6 eth1: Found Marvell 88E1111 PHY PCI: Enabling device 0002:24:0e.0 (0000 -> 0002) ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[4096] IR/IT contexts=[8/8] Bluetooth: HCI USB driver ver 2.9 hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, (U)DMA Uniform CD-ROM driver Revision: 3.20 usbcore: registered new interface driver hci_usb snd-aoa-fabric-layout: found bus with layout 51 snd-aoa-fabric-layout: Using direct GPIOs snd-aoa-codec-tas: found 'deq' node snd-aoa-fabric-layout: can use this codec snd-aoa-codec-tas: tas found, addr 0x35 on /[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d93fffec197b6] eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) Adding 500644k swap on /dev/hda6. Priority:-1 extents:1 across:500644k EXT3 FS on hda3, internal journal SCSI subsystem initialized snd-powermac no longer handles any machines with a layout-id property in the device-tree, use snd-aoa. apm_emu: APM Emulation 0.5 initialized. device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED] pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. audit(1182253431.182:2): audit_pid=1937 old=0 by auid=4294967295 NET: Registered protocol family 10 lo: Disabled Privacy Extensions Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 ADDRCONF(NETDEV_UP): eth1: link is not ready bcm43xx: PHY connected bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27) bcm43xx: Radio turned on bcm43xx: Radio enabled by hardware bcm43xx: Chip initialized bcm43xx: 30-bit DMA initialized bcm43xx: Keys cleared bcm43xx: Selected 802.11 core (phytype 2) ADDRCONF(NETDEV_UP): eth0: link is not ready bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 SoftMAC: Open Authentication completed with 00:18:f8:fa:02:cb ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [drm] Initialized drm 1.1.0 20060810 [drm] Initialized radeon 1.25.0 20060524 on minor 0 agpgart: Putting AGP V2 device at 0000:00:0b.0 into 1x mode agpgart: Putting AGP V2 device at 0000:00:10.0 into 1x mode [drm] Setting GART location based on new memory map [drm] Loading R300 Microcode [drm] writeback test succeeded in 1 usecs eth1: Link is up at 1000 Mbps, full-duplex. eth1: Pause is disabled ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready SoftMAC: Open Authentication completed with 00:18:f8:fa:02:cb ** Loaded modules: Module Size Used by binfmt_misc 13288 1 radeon 141640 2 drm 94328 3 radeon rfcomm 44060 0 l2cap 24996 5 rfcomm nfs 280008 0 nfsd 244524 17 exportfs 6272 1 nfsd lockd 75032 3 nfs,nfsd nfs_acl 4000 2 nfs,nfsd sunrpc 195616 13 nfs,nfsd,lockd,nfs_acl autofs4 24932 0 ipv6 287180 24 dm_snapshot 20320 0 dm_mirror 24212 0 dm_mod 66444 2 dm_snapshot,dm_mirror cpufreq_userspace 4564 1 apm_emu 7820 1 sr_mod 19972 0 snd_powermac 48160 0 sbp2 24516 0 scsi_mod 177708 2 sr_mod,sbp2 eth1394 21124 0 snd_aoa_codec_tas 15104 2 snd_aoa_fabric_layout 13832 1 snd_aoa 20576 2 snd_aoa_codec_tas,snd_aoa_fabric_layout snd_aoa_i2sbus 24356 1 snd_pcm_oss 52096 0 snd_mixer_oss 20384 1 snd_pcm_oss snd_pcm 92004 3 snd_powermac,snd_aoa_i2sbus,snd_pcm_oss snd_timer 25828 1 snd_pcm snd_page_alloc 11208 1 snd_pcm snd 67476 11 snd_powermac,snd_aoa_codec_tas,snd_aoa_fabric_layout,snd_aoa,snd_aoa_i2sbus,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer soundcore 8900 1 snd pcmcia 44080 0 snd_aoa_soundbus 7908 2 snd_aoa_fabric_layout,snd_aoa_i2sbus ide_cd 47236 0 hci_usb 18364 2 cdrom 43164 2 sr_mod,ide_cd ohci1394 41488 0 i2c_powermac 5984 0 bluetooth 62124 7 rfcomm,l2cap,hci_usb sungem 34916 0 sungem_phy 12896 1 sungem ehci_hcd 37196 0 ieee1394 110672 3 sbp2,eth1394,ohci1394 bcm43xx 441276 0 firmware_class 11168 2 pcmcia,bcm43xx ieee80211softmac 32032 1 bcm43xx yenta_socket 29740 1 rsrc_nonstatic 12704 1 yenta_socket ieee80211 34661 2 bcm43xx,ieee80211softmac ieee80211_crypt 6464 1 ieee80211 pcmcia_core 46968 3 pcmcia,yenta_socket,rsrc_nonstatic uninorth_agp 11724 1 agpgart 40284 2 drm,uninorth_agp tsdev 9120 0 ext3 152904 1 jbd 67880 1 ext3 mbcache 9540 1 ext3 ide_disk 18784 3 evdev 12448 8 ** PCI devices: 0000:00:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 AGP [106b:0034] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 16, Cache Line Size: 32 bytes Capabilities: <access denied> 0000:00:10.0 VGA compatible controller [0300]: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA]) Subsystem: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 255 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 48 Region 0: Memory at b8000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 0400 [size=256] Region 2: Memory at b0000000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at f1000000 [disabled] [size=128K] Capabilities: <access denied> 0001:10:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 PCI [106b:0035] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 16, Cache Line Size: 32 bytes 0001:10:12.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03) Subsystem: Apple Computer Inc. AirPort Extreme [106b:004e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 16 Interrupt: pin A routed to IRQ 52 Region 0: Memory at a0006000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> 0001:10:13.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus Controller [104c:ac56] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 53 Region 0: Memory at a0004000 (32-bit, non-prefetchable) [size=4K] Bus: primary=10, secondary=11, subordinate=14, sec-latency=176 Memory window 0: 90000000-9ffff000 (prefetchable) Memory window 1: f3000000-f33ff000 I/O window 0: 00001000-000011ff I/O window 1: 00001400-000015ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 0001:10:17.0 Unknown class [ff00]: Apple Computer Inc. KeyLargo/Intrepid Mac I/O [106b:003e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 16, Cache Line Size: 32 bytes Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K] 0001:10:18.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 27 0001:10:19.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 28 0001:10:1a.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 16 (750ns min, 21500ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 29 Region 0: Memory at a0003000 (32-bit, non-prefetchable) [size=4K] 0001:10:1b.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 63 Region 0: Memory at a0002000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> 0001:10:1b.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 63 Region 0: Memory at a0001000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> 0001:10:1b.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI]) Subsystem: NEC Corporation USB 2.0 [1033:00e0] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 63 Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> 0002:24:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 Internal PCI [106b:0036] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 16, Cache Line Size: 32 bytes 0002:24:0d.0 Unknown class [ff00]: Apple Computer Inc. UniNorth/Intrepid ATA/100 [106b:003b] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 32, Cache Line Size: 32 bytes Interrupt: pin ? routed to IRQ 39 Region 0: Memory at f5004000 (32-bit, non-prefetchable) [size=16K] 0002:24:0e.0 FireWire (IEEE 1394) [0c00]: Apple Computer Inc. UniNorth 2 FireWire [106b:0031] (rev 81) (prog-if 10 [OHCI]) Subsystem: Apple Computer Inc. iBook G4 2004 [106b:5811] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 40 Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> 0002:24:0f.0 Ethernet controller [0200]: Apple Computer Inc. UniNorth 2 GMAC (Sun GEM) [106b:0032] (rev 80) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 16 (16000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 41 Region 0: Memory at f5200000 (32-bit, non-prefetchable) [size=2M] Expansion ROM at f5100000 [disabled] [size=1M] -- System Information: Debian Release: lenny/sid APT prefers unstable APT policy: (500, 'unstable') Architecture: powerpc (ppc) Kernel: Linux 2.6.21-1-powerpc Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages linux-image-2.6.21-1-powerpc depends on: ii mkvmlinuz 33 create a kernel to boot a PowerPC ii module-init-tools 3.3-pre11-3 tools for managing Linux kernel mo ii yaird [linux-initramfs-tool] 0.0.12-20 Yet Another mkInitRD linux-image-2.6.21-1-powerpc recommends no packages. -- debconf information: linux-image-2.6.21-1-powerpc/preinst/lilo-has-ramdisk: linux-image-2.6.21-1-powerpc/postinst/bootloader-error-2.6.21-1-powerpc: linux-image-2.6.21-1-powerpc/preinst/overwriting-modules-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/postinst/bootloader-test-error-2.6.21-1-powerpc: linux-image-2.6.21-1-powerpc/preinst/initrd-2.6.21-1-powerpc: linux-image-2.6.21-1-powerpc/preinst/failed-to-move-modules-2.6.21-1-powerpc: linux-image-2.6.21-1-powerpc/preinst/abort-overwrite-2.6.21-1-powerpc: * linux-image-2.6.21-1-powerpc/preinst/already-running-this-2.6.21-1-powerpc: linux-image-2.6.21-1-powerpc/postinst/old-initrd-link-2.6.21-1-powerpc: true shared/kernel-image/really-run-bootloader: true linux-image-2.6.21-1-powerpc/preinst/bootloader-initrd-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/prerm/removing-running-kernel-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/postinst/old-dir-initrd-link-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/postinst/depmod-error-initrd-2.6.21-1-powerpc: false linux-image-2.6.21-1-powerpc/postinst/old-system-map-link-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/preinst/elilo-initrd-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/preinst/abort-install-2.6.21-1-powerpc: linux-image-2.6.21-1-powerpc/postinst/create-kimage-link-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/preinst/lilo-initrd-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/prerm/would-invalidate-boot-loader-2.6.21-1-powerpc: true linux-image-2.6.21-1-powerpc/postinst/depmod-error-2.6.21-1-powerpc: false linux-image-2.6.21-1-powerpc/postinst/kimage-is-a-directory: -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
