Hi Oleg Sorry for taking so long to reply.
On Thursday 05 October 2006 06:55, you wrote: > On Tue, Oct 03, 2006 at 04:30:13PM +0200, Georg Wittenburg wrote: > > On Tuesday 03 October 2006 16:24, you wrote: > > > On 2006-10-02, Georg Wittenburg <[EMAIL PROTECTED]> wrote: > > [.] > > > > Please don't be so selfish ;), attach full bootlog (dmesg + mount > > > output). Here i see hdb, that means device node for your drive set up. > > > What's problem, is not clear. > > [.] > > > No problem. ;) Please find attached to complete dmesg output of 2.6.16, > > 2.6.17 and 2.6.18. 2.6.16 works as expected, 2.6.17 and 2.6.18 fail to > > detect the DVD drive. > > OK, but before will go further with this, can you give 2.6.19-rc1 a try ? > 2.6.18 had very long cycle, maybe that was fixed already. I tried 2.6.19-rc1 with Debian's /boot/config-2.6.18-1-686 and default values for all new options. Unfortunately, even 2.6.19-rc1 fails to detect the DVD drive. I'm attaching the dmesg output to this mail. > > Linux version 2.6.17-2-686 (Debian 2.6.17-9) ([EMAIL PROTECTED]) (gcc > > version 4.1.2 20060901 (prerelease) (Debian 4.1.1-13)) #1 SMP Wed Sep 13 > > 16:34:10 UTC 2006 > > [.] > > > ACPI: PM-Timer IO Port: 0x1008 > > ACPI: Local APIC address 0xfee00000 > > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] *enabled*) > > > Processor #0 6:13 APIC version 20 > > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] *disabled*) > > > ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > > BTW, do you have a Core Duo ? If yes, do they both run ? No, this is a plain Pentium M. [EMAIL PROTECTED]:~$ cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.86GHz stepping : 8 cpu MHz : 800.000 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush dts acpi mmx fxsr sse sse2 ss tm pbe nx est tm2 bogomips : 1599.97 > > ACPI: Local APIC address 0xfee00000 > > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] *enabled*) > > > Processor #0 6:13 APIC version 20 > > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] *disabled*) > > > ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > > ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) I'm unsure whether this helps, but I've observed for all of 2.6.17, 2.6.18, and 2.6.19-rc1 that there is a delay lasting several seconds during boot after the line "hda: TOSHIBA MK1031GAS, ATA DISK drive". This delay doesn't happen when booting 2.6.16. Maybe a timeout during the detecting of hdb? Again, thanks for looking into this, Georg -- Georg Wittenburg http://page.mi.fu-berlin.de/~wittenbu/
Linux version 2.6.19-rc1 ([EMAIL PROTECTED]) (gcc version 4.1.2 20060901
(prerelease) (Debian 4.1.1-13)) #1 SMP Sun Oct 8 16:19:23 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
BIOS-e820: 000000003fee0000 - 000000003feea000 (ACPI data)
BIOS-e820: 000000003feea000 - 000000003ff00000 (ACPI NVS)
BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
126MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 261856) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 261856
early_node_map[1] active PFN ranges
0: 0 -> 261856
On node 0 totalpages: 261856
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 253 pages used for memmap
HighMem zone: 32227 pages, LIFO batch:7
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7520
ACPI: RSDT (v001 Sony J1 0x20060605 PTL 0x00000000) @ 0x3fee5890
ACPI: MADT (v001 Sony J1 0x20060605 PTL 0x0000005f) @ 0x3fee9e78
ACPI: FADT (v002 Sony J1 0x20060605 PTL 0x0000005f) @ 0x3fee9ee0
ACPI: BOOT (v001 Sony J1 0x20060605 PTL 0x00000001) @ 0x3fee9fd8
ACPI: MCFG (v001 Sony J1 0x20060605 PTL 0x0000005f) @ 0x3fee9f9c
ACPI: SSDT (v001 Sony J1 0x20060605 PTL 0x20030224) @ 0x3fee614d
ACPI: SSDT (v001 Sony J1 0x20060605 PTL 0x20030224) @ 0x3fee5d08
ACPI: SSDT (v001 Sony J1 0x20060605 PTL 0x20030224) @ 0x3fee5aed
ACPI: SSDT (v001 Sony J1 0x20060605 PTL 0x20030224) @ 0x3fee58d4
ACPI: DSDT (v001 Sony J1 0x20060605 PTL 0x20030224) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
Detected 1862.385 MHz processor.
Built 1 zonelists. Total pages: 259811
Kernel command line: root=/dev/hda6 ro vga=791 resume2=swap:/dev/hda5
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030552k/1047424k available (1566k kernel code, 16180k reserved, 591k
data, 192k init, 129920k highmem)
virtual kernel memory layout:
fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0321000 - 0xc0351000 ( 192 kB)
.data : 0xc028794e - 0xc031b894 ( 591 kB)
.text : 0xc0100000 - 0xc028794e (1566 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3728.40 BogoMIPS (lpj=7456816)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180
00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) M processor 1.86GHz stepping 08
Total of 1 processors activated (3728.40 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 4493k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Firmware left 0000:06:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06 (-#07) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: Embedded Controller [EC] (gpe 23) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: 90000000-afffffff
PREFETCH window: c0000000-cfffffff
PCI: Bus 7, cardbus bridge: 0000:06:03.0
IO window: 00002400-000024ff
IO window: 00002800-000028ff
PREFETCH window: 50000000-51ffffff
MEM window: 52000000-53ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: b0000000-b00fffff
PREFETCH window: 50000000-51ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:06:03.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1160327549.980:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 3072k, total
32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d360
vesafb: pmi: set display start = c00cd396, set palette = c00cd400
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf
3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4<6>Time: tsc clocksource has been installed.
S5)
Freeing unused kernel memory: 192k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not
present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Thermal Zone [THRM] (68 C)
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ACPI: PCI Interrupt 0000:06:08.0[A] -> GSI 20 (level, low) -> IRQ 17
e100: eth0: e100_probe: addr 0xb0007000, irq 17, MAC addr 00:01:4A:5E:E3:1D
ieee1394: Initialized config rom entry `ip1394'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
Time: acpi_pm clocksource has been installed.
hda: TOSHIBA MK1031GAS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt 0000:06:03.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[b0004000-b00047ff]
Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0x80004000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hda: max request size: 512KiB
hda: 195371568 sectors (100030 MB), CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda:<6>ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 19, io base 0x00001800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hda1 hda2 < hda5 hda6 hda7 >
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci1394: fw-host0: Running dma failed because Node ID is not valid
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
ohci1394: fw-host0: AT dma reset ctx=0, aborting transmission
ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
Attempting manual resume
kjournald starting. Commit interval 5 seconds
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800460301e35f41]
EXT3-fs: mounted filesystem with ordered data mode.
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 1-1.4: new high speed USB device using ehci_hcd and address 4
usb 1-1.4: configuration #1 chosen from 1 choice
hub 1-1.4:1.0: USB hub found
hub 1-1.4:1.0: 4 ports detected
usb 1-1.4.1: new high speed USB device using ehci_hcd and address 5
usb 1-1.4.1: configuration #1 chosen from 1 choice
usb 1-1.4.4: new full speed USB device using ehci_hcd and address 6
usb 1-1.4.4: configuration #1 chosen from 1 choice
Yenta: CardBus bridge found at 0000:06:03.0 [104d:818f]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:03.0, mfunc 0x01001b22, devctl 0x64
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0xb0000000 - 0xb00fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input1
input: PS/2 Mouse as /class/input/input2
intel_rng: FWH not detected
input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
usbcore: registered new interface driver hiddev
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]>
input: Logitech Optical USB Mouse as /class/input/input4
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 20
Bluetooth: HCI USB driver ver 2.9
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.4kmq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 22 (level, low) -> IRQ 21
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
usbcore: registered new interface driver hci_usb
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
usbcore: registered new interface driver snd-usb-audio
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
Adding 1959888k swap on /dev/hda5. Priority:-1 extents:1 across:1959888k
EXT3 FS on hda6, internal journal
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect
breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Power Button (CM) [PWRB]
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
IPv6 over IPv4 tunneling driver
sonypi: Sony Programmable I/O Controller Driver v1.26.
sonypi: detected type3 model, verbose = 0, fnkeyinit = off, camera = off,
compat = off, mask = 0xffffffff, useinput = on, acpi = on
sonypi: enabled at irq=11, port1=0x1080, port2=0x1084
sonypi: device allocated minor is 62
input: Sony Vaio Jogdial as /class/input/input5
input: Sony Vaio Keys as /class/input/input6
sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 657)
sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 659)
sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
pgpIKA1WsIq0J.pgp
Description: PGP signature
