Package: linux-image-2.6.18-1-686 Version: 2.6.18-2 Severity: important
This is very similar to http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=380272 The same workaround could be used to overcome the problem: cat cpqarray >> /etc/initramfs-tools/modules update-initramfs -u lspci -v output from the system booted with enabled workaround: -- begin -- 00:00.0 Host bridge: Broadcom CNB20LE Host Bridge (rev 05) Flags: bus master, medium devsel, latency 64 00:00.1 Host bridge: Broadcom CNB20LE Host Bridge (rev 05) Flags: bus master, medium devsel, latency 64 00:01.0 RAID bus controller: LSI Logic / Symbios Logic 53C1510 (rev 02) Subsystem: Compaq Computer Corporation Integrated Array Controller Flags: bus master, medium devsel, latency 192, IRQ 177 I/O ports at 2000 [size=256] Memory at c5000000 (32-bit, non-prefetchable) [size=16M] Memory at c4000000 (32-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 50100000 [disabled] [size=512K] Capabilities: [40] Power Management version 2 00:02.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Compaq Computer Corporation NC3163 Fast Ethernet NIC (embedded, WOL) Flags: bus master, medium devsel, latency 64, IRQ 193 Memory at c3fff000 (32-bit, non-prefetchable) [size=4K] I/O ports at 2400 [size=64] Memory at c3e00000 (32-bit, non-prefetchable) [size=1M] [virtual] Expansion ROM at 50000000 [disabled] [size=1M] Capabilities: [dc] Power Management version 2 00:03.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC] (rev 7a) (prog-if 00 [VGA]) Subsystem: ATI Technologies Inc Rage IIC Flags: bus master, stepping, medium devsel, latency 64 Memory at c2000000 (32-bit, prefetchable) [size=16M] I/O ports at 2800 [size=256] Memory at c3dff000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 50180000 [disabled] [size=128K] Capabilities: [5c] Power Management version 1 00:04.0 System peripheral: Compaq Computer Corporation Advanced System Management Controller Subsystem: Compaq Computer Corporation Unknown device b0f3 Flags: medium devsel, IRQ 255 I/O ports at 1800 [size=256] Memory at c3dfef00 (32-bit, non-prefetchable) [size=256] 00:0f.0 ISA bridge: Broadcom OSB4 South Bridge (rev 4f) Subsystem: Broadcom OSB4 South Bridge Flags: bus master, medium devsel, latency 0 00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8a [Master SecP PriP]) Flags: bus master, medium devsel, latency 64 I/O ports at 2c00 [size=16] 03:04.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller Subsystem: Netgear FA311 / FA312 (FA311 with WoL HW) Flags: bus master, medium devsel, latency 64, IRQ 185 I/O ports at 3000 [size=256] Memory at c6fff000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 501a0000 [disabled] [size=64K] Capabilities: [40] Power Management version 2 -- end -- Boot console and dmesg log from failed boot: -- begin -- Booting 'Debian GNU/Linux, kernel 2.6.18-1-686' root (hd0,0) Filesystem type is ext2fs, partition type 0x83 kernel /boot/vmlinuz-2.6.18-1-686 root=/dev/ida/c0d0p1 ro console=tty0 console =ttyS0,38400n8 [Linux-bzImage, setup=0x1e00, size=0x130471] initrd /boot/initrd.img-2.6.18-1-686 [Linux-initrd @ 0x1fbae000, 0x4419ba bytes] savedefault Linux version 2.6.18-1-686 (Debian 2.6.18-2) ([EMAIL PROTECTED]) (gcc version 4.1.2 20060920 (prerelease) (Debian 4.1.1-14)) #1 SMP6 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fffc000 (usable) BIOS-e820: 000000003fffc000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f4ff0 DMI 2.3 present. ACPI: PM-Timer IO Port: 0x240 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 17 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 6:8 APIC version 17 ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI 0-34 Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) Detected 797.550 MHz processor. Built 1 zonelists. Total pages: 262140 Kernel command line: root=/dev/ida/c0d0p1 ro console=tty0 console=ttyS0,38400n8 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1031832k/1048560k available (1534k kernel code, 16044k reserved, 575k data, 196k init, 131056k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1596.04 BogoMIPS (lpj=3192085) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU0: Intel Pentium III (Coppermine) stepping 03 SMP alternatives: switching to SMP code Booting processor 1/0 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 1595.08 BogoMIPS (lpj=3190174) CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Pentium III (Coppermine) stepping 03 Total of 2 processors activated (3191.12 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=929 checking if image is initramfs... it is Freeing initrd memory: 4358k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0084, last bus=3 PCI: Using configuration type 1 Setting up standard PCI resources mtrr: your CPUs had inconsistent fixed MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Firmware left 0000:00:02.0 e100 interrupts enabled, disabling ACPI: PCI Root Bridge [PCI1] (0000:03) ACPI: Resource is not an IRQ entry ACPI: PCI Interrupt Link [FAKE] (IRQs) *0, disabled. ACPI: PCI Interrupt Link [INA0] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA1] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA2] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA3] (IRQs 5 10 *11 15) ACPI: PCI Interrupt Link [INA4] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA5] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [ITR0] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [ITR1] (IRQs 5 *10 11 15) ACPI: PCI Interrupt Link [ITR2] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [ITR3] (IRQs *5 10 11 15) ACPI: PCI Interrupt Link [INB0] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB1] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB2] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB3] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB4] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB5] (IRQs 5 10 11 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Device 0000:00:00.0 not found by BIOS PCI: Device 0000:00:00.1 not found by BIOS PCI: Device 0000:00:0f.0 not found by BIOS pnp: 00:01: ioport range 0xf50-0xf58 has been reserved NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1160125423.552:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Starting balanced_irq Using IPI No-Shortcut mode ACPI: (supports<6>Time: tsc clocksource has been installed. S0 S4 S5) Freeing unused kernel memory: 196k freed input: AT Translated Set 2 keyboard as /class/input/input0 Loading, please wait... Begin: Loading essential drivers... ... Done. Begin: Running /scripts/init-premount ... ACPI: Thermal Zone [THM0] (8 C) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1 SvrWks OSB4: chipset revision 0 SvrWks OSB4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x2c00-0x2c07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x2c08-0x2c0f, BIOS settings: hdc:pio, hdd:pio natsemi dp8381x driver, version 2.0, June 27, 2006 originally by Donald Becker <[EMAIL PROTECTED]> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation SCSI subsystem initialized hda: CD-224E, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ACPI: PCI Interrupt 0000:03:04.0[A] -> <6>ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 17 (level, low) -> IRQ 185 GSI 27 (level, low) -> IRQ 177 natsemi eth0: NatSemi DP8381[56] at 0xc6fff000 (0000:03:04.0), 00:0f:b5:fa:bd:2d, IRQ 177, port TP. e100: eth0: e100_probe: addr 0xc3fff000, irq 185, MAC addr 00:02:A5:0A:57:CF ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 193 sym53c8xx 0000:00:01.0: device not supported ACPI: PCI interrupt for device 0000:00:01.0 disabled hda: ATAPI 24X CD-ROM drive, 512kB Cache Uniform CD-ROM driver Revision: 3.20 Compaq SMART2 Driver (v 2.6.0) PCI: Enabling device 0000:00:01.0 (0110 -> 0113) ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 193 cpqarray: Finding drives on ida0<4>cpqarray ida0: idaSendPciCmd Timeout out, No command list address returned! cpqarray: error sending ID controller cpqarray ida0: idaSendPciCmd Timeout out, No command list address returned! cpqarray: Unable to start background processing Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Done. Begin: Waiting for root file system... ... Done. Check root= bootarg cat /proc/cmdline or missing modules, devices: cat /proc/modules ls /dev ALERT! /dev/ida/c0d0p1 does not exist. Dropping to a shell! BusyBox v1.1.3 (Debian 1:1.1.3-3) Built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs) lspci -v /bin/sh: lspci: not found (initramfs) find / -name lspci (initramfs) dmesg Ok. Calibrating delay using timer specific routine.. 1596.04 BogoMIPS (lpj=3192085) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU0: Intel Pentium III (Coppermine) stepping 03 SMP alternatives: switching to SMP code Booting processor 1/0 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 1595.08 BogoMIPS (lpj=3190174) CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Pentium III (Coppermine) stepping 03 Total of 2 processors activated (3191.12 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=929 checking if image is initramfs... it is Freeing initrd memory: 4358k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0084, last bus=3 PCI: Using configuration type 1 Setting up standard PCI resources mtrr: your CPUs had inconsistent fixed MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Firmware left 0000:00:02.0 e100 interrupts enabled, disabling Boot video device is 0000:00:03.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Root Bridge [PCI1] (0000:03) PCI: Probing PCI hardware (bus 03) ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT] ACPI: Resource is not an IRQ entry ACPI: PCI Interrupt Link [FAKE] (IRQs) *0, disabled. ACPI: PCI Interrupt Link [INA0] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA1] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA2] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA3] (IRQs 5 10 *11 15) ACPI: PCI Interrupt Link [INA4] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INA5] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [ITR0] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [ITR1] (IRQs 5 *10 11 15) ACPI: PCI Interrupt Link [ITR2] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [ITR3] (IRQs *5 10 11 15) ACPI: PCI Interrupt Link [INB0] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB1] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB2] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB3] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB4] (IRQs 5 10 11 15) *0, disabled. ACPI: PCI Interrupt Link [INB5] (IRQs 5 10 11 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Device 0000:00:00.0 not found by BIOS PCI: Device 0000:00:00.1 not found by BIOS PCI: Device 0000:00:0f.0 not found by BIOS pnp: 00:01: ioport range 0xf50-0xf58 has been reserved NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1160125423.552:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Starting balanced_irq Using IPI No-Shortcut mode ACPI: (supports<6>Time: tsc clocksource has been installed. S0 S4 S5) Freeing unused kernel memory: 196k freed input: AT Translated Set 2 keyboard as /class/input/input0 ACPI: Thermal Zone [THM0] (8 C) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1 SvrWks OSB4: chipset revision 0 SvrWks OSB4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x2c00-0x2c07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x2c08-0x2c0f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... natsemi dp8381x driver, version 2.0, June 27, 2006 originally by Donald Becker <[EMAIL PROTECTED]> http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation SCSI subsystem initialized hda: CD-224E, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... ACPI: PCI Interrupt 0000:03:04.0[A] -> <6>ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 17 (level, low) -> IRQ 185 GSI 27 (level, low) -> IRQ 177 natsemi eth0: NatSemi DP8381[56] at 0xc6fff000 (0000:03:04.0), 00:0f:b5:fa:bd:2d, IRQ 177, port TP. e100: eth0: e100_probe: addr 0xc3fff000, irq 185, MAC addr 00:02:A5:0A:57:CF ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 193 sym53c8xx 0000:00:01.0: device not supported ACPI: PCI interrupt for device 0000:00:01.0 disabled hda: ATAPI 24X CD-ROM drive, 512kB Cache Uniform CD-ROM driver Revision: 3.20 Compaq SMART2 Driver (v 2.6.0) cpqarray: Device 0x10 has been found at bus 0 dev 1 func 0 PCI: Enabling device 0000:00:01.0 (0110 -> 0113) ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 19 (level, low) -> IRQ 193 cpqarray: Finding drives on ida0<4>cpqarray ida0: idaSendPciCmd Timeout out, No command list address returned! cpqarray: error sending ID controller cpqarray: Starting firmware's background processing cpqarray ida0: idaSendPciCmd Timeout out, No command list address returned! cpqarray: Unable to start background processing Probing IDE interface ide1... (initramfs) -- end -- -- System Information: Debian Release: testing/unstable APT prefers testing APT policy: (990, 'testing'), (500, 'unstable') Architecture: i386 (i686) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.18-1-686 Locale: LANG=en_US, LC_CTYPE=en_US (charmap=ISO-8859-1) Versions of packages linux-image-2.6.18-1-686 depends on: ii initramfs-tools [linux-initra 0.80 tools for generating an initramfs ii module-init-tools 3.2.2-3 tools for managing Linux kernel mo Versions of packages linux-image-2.6.18-1-686 recommends: ii libc6-i686 2.3.6.ds1-4 GNU C Library: Shared libraries [i -- debconf information: linux-image-2.6.18-1-686/postinst/bootloader-error-2.6.18-1-686: shared/kernel-image/really-run-bootloader: true linux-image-2.6.18-1-686/postinst/depmod-error-initrd-2.6.18-1-686: false linux-image-2.6.18-1-686/postinst/create-kimage-link-2.6.18-1-686: true linux-image-2.6.18-1-686/preinst/initrd-2.6.18-1-686: linux-image-2.6.18-1-686/preinst/abort-overwrite-2.6.18-1-686: linux-image-2.6.18-1-686/preinst/elilo-initrd-2.6.18-1-686: true linux-image-2.6.18-1-686/postinst/old-initrd-link-2.6.18-1-686: true linux-image-2.6.18-1-686/preinst/already-running-this-2.6.18-1-686: linux-image-2.6.18-1-686/preinst/lilo-has-ramdisk: linux-image-2.6.18-1-686/postinst/bootloader-test-error-2.6.18-1-686: linux-image-2.6.18-1-686/postinst/depmod-error-2.6.18-1-686: false linux-image-2.6.18-1-686/postinst/old-dir-initrd-link-2.6.18-1-686: true linux-image-2.6.18-1-686/preinst/overwriting-modules-2.6.18-1-686: true linux-image-2.6.18-1-686/preinst/failed-to-move-modules-2.6.18-1-686: linux-image-2.6.18-1-686/preinst/lilo-initrd-2.6.18-1-686: true linux-image-2.6.18-1-686/prerm/removing-running-kernel-2.6.18-1-686: true linux-image-2.6.18-1-686/postinst/old-system-map-link-2.6.18-1-686: true linux-image-2.6.18-1-686/prerm/would-invalidate-boot-loader-2.6.18-1-686: true linux-image-2.6.18-1-686/preinst/bootloader-initrd-2.6.18-1-686: true linux-image-2.6.18-1-686/preinst/abort-install-2.6.18-1-686: linux-image-2.6.18-1-686/postinst/kimage-is-a-directory: -- ...Bye..Dmitry. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
