Package: linux-image-2.6.15-1-686
Version: 2.6.15-6
Severity: normal
I'm having quite frequent lockups on my SATA system. The controller is
a Silicon Image Sil3512A. The system is a Shuttle SN85G4V2 barebone
with AMD 64 CPU, 1 gig memory and Seagate Barracuda 7200.7 SATA 200 GB
disk.
Immediately before the lockup, the following is printed to the
console:
ata1: command 0x35 timeout, stat 0x58 host_stat 0x61
ata1: status=0x58 { DriveReady SeekComplete DataRequest }
sd 0:0:0:0: SCSI error: return code = 0x8000002
sda: Current: sense key: Aborted Command
Additional sense: Scsi parity error
end_request: I/O error, dev sda, sector 57582833
Buffer I/O error on device sda6, logical block 3097255
lost page write due to I/O error on sda6
ATA: abnormal status 0x58 on port 0xF8802087
ATA: abnormal status 0x58 on port 0xF8802087
ATA: abnormal status 0x58 on port 0xF8802087
Originally, a disk failure was suspected. We bought another disk,
mounted it as sdb and started copying from old to new. The system
locked up before 2 Gb had been copied, same message as above - but
this time from sdb, the new disk.
Having eliminated the disk, we suspected the motherboard, and the
barebone was shipped back to the vendor. They reported back that they
had tested it extensively, in particular doing large copies under
Windows. This was with different CPU, memory and disk than we used,
but seems to indicate that the problem could be in the linux kernel.
The driver appears to be sata_sil.
I hope you have suggestions on how to proceed with this
problem.
Regards
Jon K Hellan
lspci output:
0000:00:00.0 Host bridge: nVidia Corporation nForce3 Host Bridge (rev a4)
0000:00:01.0 ISA bridge: nVidia Corporation nForce3 LPC Bridge (rev a6)
0000:00:01.1 SMBus: nVidia Corporation nForce3 SMBus (rev a4)
0000:00:02.0 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
0000:00:02.1 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
0000:00:02.2 USB Controller: nVidia Corporation nForce3 USB 2.0 (rev a2)
0000:00:05.0 Ethernet controller: nVidia Corporation nForce3 Ethernet (rev a5)
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce3 Audio (rev
a2)
0000:00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5)
0000:00:0a.0 PCI bridge: nVidia Corporation nForce3 PCI Bridge (rev a2)
0000:00:0b.0 PCI bridge: nVidia Corporation nForce3 AGP Bridge (rev a4)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
0000:01:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80)
0000:01:07.0 RAID bus controller: Silicon Image, Inc. SiI 3512
[SATALink/SATARaid] Serial ATA Controller (rev 01)
0000:02:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX
5200] (rev a1)
lspci -v output:
0000:00:00.0 Host bridge: nVidia Corporation nForce3 Host Bridge (rev a4)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0
Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] #08 [0180]
Capabilities: [c0] AGP version 3.0
0000:00:01.0 ISA bridge: nVidia Corporation nForce3 LPC Bridge (rev a6)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0
0000:00:01.1 SMBus: nVidia Corporation nForce3 SMBus (rev a4)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: 66MHz, fast devsel, IRQ 10
I/O ports at 4c00 [size=64]
I/O ports at 4c40 [size=64]
Capabilities: [44] Power Management version 2
0000:00:02.0 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
(prog-if 10 [OHCI])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 11
Memory at e0002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
0000:00:02.1 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5)
(prog-if 10 [OHCI])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 11
Memory at e0003000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
0000:00:02.2 USB Controller: nVidia Corporation nForce3 USB 2.0 (rev a2)
(prog-if 20 [EHCI])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 11
Memory at e0004000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
0000:00:05.0 Ethernet controller: nVidia Corporation nForce3 Ethernet (rev a5)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 10
Memory at e0000000 (32-bit, non-prefetchable) [size=4K]
I/O ports at b400 [size=8]
Capabilities: [44] Power Management version 2
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce3 Audio (rev
a2)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 3
I/O ports at b800 [size=256]
I/O ports at bc00 [size=128]
Memory at e0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
0000:00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5) (prog-if 8a
[Master SecP PriP])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device
a550
Flags: bus master, 66MHz, fast devsel, latency 0
I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
0000:00:0a.0 PCI bridge: nVidia Corporation nForce3 PCI Bridge (rev a2)
(prog-if 00 [Normal decode])
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=128
I/O behind bridge: 00009000-0000afff
Memory behind bridge: de000000-dfffffff
Prefetchable memory behind bridge: 50000000-500fffff
0000:00:0b.0 PCI bridge: nVidia Corporation nForce3 AGP Bridge (rev a4)
(prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 16
Bus: primary=00, secondary=02, subordinate=02, sec-latency=10
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: [80] #08 [2101]
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Flags: fast devsel
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
Flags: fast devsel
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Flags: fast devsel
0000:01:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Flags: bus master, medium devsel, latency 32, IRQ 9
Memory at df001000 (32-bit, non-prefetchable) [size=2K]
I/O ports at 9000 [size=128]
Capabilities: [50] Power Management version 2
0000:01:07.0 RAID bus controller: Silicon Image, Inc. SiI 3512
[SATALink/SATARaid] Serial ATA Controller (rev 01)
Subsystem: Silicon Image, Inc. SiI 3512 SATARaid Controller
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
I/O ports at 9400 [size=8]
I/O ports at 9800 [size=4]
I/O ports at 9c00 [size=8]
I/O ports at a000 [size=4]
I/O ports at a400 [size=16]
Memory at df000000 (32-bit, non-prefetchable) [size=512]
Expansion ROM at 50000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
0000:02:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX
5200] (rev a1) (prog-if 00 [VGA])
Subsystem: CardExpert Technology: Unknown device 0431
Flags: bus master, 66MHz, medium devsel, latency 248, IRQ 5
Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Memory at d0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at dd000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 3.0
lsmod output:
Module Size Used by
wacom 14144 0
nvidia 4088368 12
rfcomm 33880 3
l2cap 21188 5 rfcomm
bluetooth 41732 4 rfcomm,l2cap
binfmt_misc 10600 1
lp 10532 0
ipv6 221664 22
it87 19140 0
hwmon_vid 2304 1 it87
i2c_isa 4608 1 it87
snd_seq_dummy 3556 0
snd_seq_oss 28896 0
snd_seq_midi 8384 0
snd_rawmidi 22240 1 snd_seq_midi
snd_seq_midi_event 6368 2 snd_seq_oss,snd_seq_midi
snd_seq 44432 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_seq_device 7916 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
sr_mod 16260 0
sbp2 20996 0
ide_generic 1120 0 [permanent]
ide_cd 36484 0
cdrom 33280 2 sr_mod,ide_cd
eth1394 18344 0
psmouse 32356 0
serio_raw 6468 0
joydev 8864 0
amd74xx 12828 0 [permanent]
generic 4260 0 [permanent]
ide_core 112800 4 ide_generic,ide_cd,amd74xx,generic
parport_pc 32036 1
parport 31624 2 lp,parport_pc
ohci1394 30164 0
floppy 54628 0
pcspkr 1668 0
ieee1394 88152 3 sbp2,eth1394,ohci1394
rtc 11316 0
snd_intel8x0 29596 0
snd_ac97_codec 82464 1 snd_intel8x0
snd_ac97_bus 2048 1 snd_ac97_codec
snd_pcm_oss 45536 0
snd_mixer_oss 16448 1 snd_pcm_oss
sata_nv 8772 0
i2c_nforce2 6240 0
snd_pcm 77576 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 21316 2 snd_seq,snd_pcm
ehci_hcd 28904 0
ohci_hcd 17764 0
snd 48420 10
snd_seq_oss,snd_rawmidi,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
i2c_core 19280 3 it87,i2c_isa,i2c_nforce2
usbcore 113284 4 wacom,ehci_hcd,ohci_hcd
amd64_agp 11236 1
agpgart 31400 2 nvidia,amd64_agp
forcedeth 20036 0
soundcore 8928 1 snd
snd_page_alloc 9928 2 snd_intel8x0,snd_pcm
ext3 117768 2
jbd 48404 1 ext3
mbcache 8484 1 ext3
sd_mod 17072 4
sata_sil 8868 3
libata 51020 2 sata_nv,sata_sil
scsi_mod 125736 4 sr_mod,sbp2,sd_mod,libata
shpchp 39712 0
pci_hotplug 24756 1 shpchp
evdev 8800 0
mousedev 10496 2
dmesg output:
00
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.2 present.
ACPI: RSDP (v000 XPC ) @ 0x000f6a90
ACPI: RSDT (v001 XPC AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000
ACPI: FADT (v001 XPC AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: MADT (v001 XPC AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff7980
ACPI: DSDT (v001 XPC SN85 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: Skipping IOAPIC probe due to 'noapic' option.
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro noapic
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1994.749 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1035344k/1048512k available (1425k kernel code, 12432k reserved, 530k
data, 144k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3992.39 BogoMIPS (lpj=1996198)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000
00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0e28)
checking if image is initramfs... it is
Freeing initrd memory: 1011k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb7a0, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4800-0x487f has been reserved
pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
PCI: Bridge: 0000:00:0a.0
IO window: 9000-afff
MEM window: de000000-dfffffff
PREFETCH window: 50000000-500fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: dc000000-ddffffff
PREFETCH window: d0000000-d7ffffff
PCI: Setting latency timer of device 0000:00:0a.0 to 64
audit: initializing netlink socket (disabled)
audit(1140470635.347:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 144k freed
mice: PS/2 mouse device common for all mice
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
SCSI subsystem initialized
libata version 1.20 loaded.
sata_sil 0000:01:07.0: version 0.9
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNK4] -> GSI 11 (level, low) ->
IRQ 11
ata1: SATA max UDMA/100 cmd 0xF8802080 ctl 0xF880208A bmdma 0xF8802000 irq 11
ata2: SATA max UDMA/100 cmd 0xF88020C0 ctl 0xF88020CA bmdma 0xF8802008 irq 11
input: AT Translated Set 2 keyboard as /class/input/input0
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA-6, max UDMA/133, 390721968 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Vendor: ATA Model: ST3200822AS Rev: 3.01
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LMAC] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:05.0 to 64
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 64M @ 0xd8000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUBA] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 11, io mem 0xe0002000
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUBB] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 11, io mem 0xe0003000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Real Time Clock Driver v1.12
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUB2] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 11, io mem 0xe0004000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
eth0: forcedeth.c: subsystem: 01297:a550 bound to 0000:00:05.0
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 3 (level, low) -> IRQ
3
PCI: Setting latency timer of device 0000:00:06.0 to 64
usb 3-3: new high speed USB device using ehci_hcd and address 2
intel8x0_measure_ac97_clock: measured 50864 usecs
intel8x0: clocking to 47407
ieee1394: Initialized config rom entry `ip1394'
usb 3-3: config index 0 descriptor too short (expected 32, got 9)
usb 3-3: config 1 has 0 interfaces, different from the descriptor's value: 1
input: PC Speaker as /class/input/input1
FDC 0 is a post-1991 82077
ohci1394: $Rev: 1313 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNK3] -> GSI 9 (level, low) -> IRQ
9
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9] MMIO=[df001000-df0017ff] Max
Packet=[2048]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
Probing IDE interface ide1...
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00301bb400001678]
hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
input: PS2++ Logitech Wheel Mouse as /class/input/input2
eth1394: $Rev: 1312 $ Ben Collins <[EMAIL PROTECTED]>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Adding 2731008k swap on /dev/sda5. Priority:-1 extents:1 across:2731008k
EXT3 FS on sda1, internal journal
Probing IDE interface ide0...
sbp2: $Rev: 1306 $ Ben Collins <[EMAIL PROTECTED]>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
it87: Found IT8712F chip at 0x290, revision 5
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
lp0: using parport0 (interrupt-driven).
eth0: no IPv6 routers present
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.6
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNK5] -> GSI 5 (level, low) -> IRQ
5
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8178 Wed Dec 14
16:22:51 PST 2005
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
usbcore: registered new driver wacom
drivers/usb/input/wacom.c: v1.44:USB Wacom Graphire and Wacom Intuos tablet
driver
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
-- System Information:
Debian Release: testing/unstable
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'stable'), (1, 'experimental')
Architecture: i386 (i686)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.15-1-686
Locale: LANG=en_US, LC_CTYPE=en_US (charmap=ISO-8859-1)
Versions of packages linux-image-2.6.15-1-686 depends on:
ii module-init-tools 3.2.2-2 tools for managing Linux kernel mo
ii yaird [linux-initramfs-tool] 0.0.12-3 Yet Another mkInitRD
Versions of packages linux-image-2.6.15-1-686 recommends:
pn libc6-i686 <none> (no description available)
-- debconf information:
linux-image-2.6.15-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.15-1-686/preinst/overwriting-modules-2.6.15-1-686: true
linux-image-2.6.15-1-686/postinst/depmod-error-initrd-2.6.15-1-686: false
linux-image-2.6.15-1-686/postinst/bootloader-error-2.6.15-1-686:
linux-image-2.6.15-1-686/postinst/bootloader-test-error-2.6.15-1-686:
linux-image-2.6.15-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.15-1-686/preinst/failed-to-move-modules-2.6.15-1-686:
linux-image-2.6.15-1-686/postinst/old-system-map-link-2.6.15-1-686: true
linux-image-2.6.15-1-686/preinst/abort-install-2.6.15-1-686:
linux-image-2.6.15-1-686/preinst/abort-overwrite-2.6.15-1-686:
linux-image-2.6.15-1-686/preinst/bootloader-initrd-2.6.15-1-686: true
linux-image-2.6.15-1-686/prerm/would-invalidate-boot-loader-2.6.15-1-686: true
linux-image-2.6.15-1-686/preinst/lilo-initrd-2.6.15-1-686: true
linux-image-2.6.15-1-686/postinst/old-initrd-link-2.6.15-1-686: true
linux-image-2.6.15-1-686/postinst/old-dir-initrd-link-2.6.15-1-686: true
linux-image-2.6.15-1-686/preinst/already-running-this-2.6.15-1-686:
linux-image-2.6.15-1-686/preinst/initrd-2.6.15-1-686:
linux-image-2.6.15-1-686/postinst/depmod-error-2.6.15-1-686: false
linux-image-2.6.15-1-686/postinst/create-kimage-link-2.6.15-1-686: true
linux-image-2.6.15-1-686/prerm/removing-running-kernel-2.6.15-1-686: true
linux-image-2.6.15-1-686/preinst/elilo-initrd-2.6.15-1-686: true
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
