5.10 should be EOL by now
On Wed, Jan 4, 2023 at 3:51 PM Tim Düsterhus <duester...@woltlab.com> wrote:
> Package: src:linux
> Version: 5.10.158-2
> Severity: normal
> X-Debbugs-Cc: duester...@woltlab.com
>
> Dear Maintainer,
>
> after upgrading my server from Debian Buster to Debian Bullseye, I
> noticed that the underlying devices attached to the Adaptec 6405E raid
> controller were no longer exposed via the /dev/sgX devices and thus
> reading the SMART values was no longer possible:
>
> $ lsscsi
> [0:0:0:0] disk Adaptec *redacted* V1.0 /dev/sda
> [0:3:0:0] enclosu ADAPTEC Virtual SGPIO -
>
> Booting into the Linux 4.19 kernel from Debian Buster correctly exposed
> the devices with the new userland, indicating a Kernel issue.
>
> I was able to work around the issue by adding the following
> configuration to /etc/modprobe.d/:
>
> options aacraid expose_physicals=1
>
> After setting this configuration and rebooting the server the devices
> are properly visible as they were before:
>
> $ lsscsi
> [0:0:0:0] disk Adaptec *redacted* V1.0 /dev/sda
> [0:1:0:0] disk ATA *redacted* xxxx /dev/sdb
> [0:1:1:0] disk ATA *redacted* xxxx /dev/sdc
> [0:3:0:0] enclosu ADAPTEC Virtual SGPIO -
>
> Unfortunately the setting `1` allows direct write access to the devices,
> whereas the previous and to my understanding the default setting of `-1`
> only allows read access, making this a safer option.
>
> It appears that aacraid's `expose_physicals=-1` option got broken
> somewhere between Linux 4.19 and 5.10.
>
> Best regards
>
>
> -- Package-specific info:
> ** Version:
> Linux version 5.10.0-20-amd64 (debian-kernel@lists.debian.org) (gcc-10
> (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2)
> #1 SMP Debian 5.10.158-2 (2022-12-13)
>
> ** Command line:
> BOOT_IMAGE=/vmlinuz-5.10.0-20-amd64 root=ZFS=rpool/ROOT/debian ro boot=zfs
> swapaccount=1 quiet
>
> ** Tainted: POE (12289)
> * proprietary module was loaded
> * externally-built ("out-of-tree") module was loaded
> * unsigned module was loaded
>
> ** Kernel log:
> Unable to read kernel log; any relevant messages should be attached
>
> ** Model information
> sys_vendor: Supermicro
> product_name: X10SLH-F/X10SLM+-F
> product_version: 0123456789
> chassis_vendor: Supermicro
> chassis_version: 0123456789
> bios_vendor: American Megatrends Inc.
> bios_version: 3.2a
> board_vendor: Supermicro
> board_name: X10SLH-F/X10SLM+-F
> board_version: 1.02
>
> ** Loaded modules:
> nft_reject_inet
> nf_reject_ipv4
> nf_reject_ipv6
> nft_reject
> nft_counter
> intel_rapl_msr
> intel_rapl_common
> ipmi_ssif
> nft_ct
> nf_conntrack
> nf_defrag_ipv6
> nf_defrag_ipv4
> x86_pkg_temp_thermal
> intel_powerclamp
> coretemp
> kvm_intel
> kvm
> ext4
> irqbypass
> ghash_clmulni_intel
> crc16
> mbcache
> jbd2
> aesni_intel
> libaes
> crypto_simd
> cryptd
> ast
> glue_helper
> drm_vram_helper
> drm_ttm_helper
> rapl
> ttm
> intel_cstate
> intel_uncore
> drm_kms_helper
> pcspkr
> joydev
> at24
> intel_pch_thermal
> evdev
> mei_me
> cec
> iTCO_wdt
> mei
> intel_pmc_bxt
> sg
> iTCO_vendor_support
> watchdog
> ie31200_edac
> acpi_ipmi
> ipmi_si
> ipmi_devintf
> ipmi_msghandler
> acpi_pad
> button
> nf_tables
> libcrc32c
> crc32c_generic
> nfnetlink
> drm
> fuse
> configfs
> ip_tables
> x_tables
> autofs4
> hid_generic
> usbhid
> hid
> zfs(POE)
> zunicode(POE)
> zzstd(OE)
> zlua(OE)
> zavl(POE)
> icp(POE)
> zcommon(POE)
> znvpair(POE)
> spl(OE)
> ses
> enclosure
> sd_mod
> scsi_transport_sas
> t10_pi
> crc_t10dif
> crct10dif_generic
> ahci
> libahci
> xhci_pci
> libata
> xhci_hcd
> ehci_pci
> crct10dif_pclmul
> crct10dif_common
> ehci_hcd
> aacraid
> crc32_pclmul
> lpc_ich
> igb
> i2c_i801
> usbcore
> i2c_smbus
> scsi_mod
> crc32c_intel
> i2c_algo_bit
> dca
> ptp
> pps_core
> usb_common
> fan
> video
>
> ** PCI devices:
> 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v3 Processor
> DRAM Controller [8086:0c08] (rev 06)
> Subsystem: Super Micro Computer Inc Xeon E3-1200 v3 Processor DRAM
> Controller [15d9:0803]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR- INTx-
> Latency: 0
> IOMMU group: 0
> Capabilities: [e0] Vendor Specific Information: Len=0c <?>
> Kernel driver in use: ie31200_edac
> Kernel modules: ie31200_edac
>
> 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v3/4th Gen Core
> Processor PCI Express x16 Controller [8086:0c01] (rev 06) (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 25
> IOMMU group: 1
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: [disabled]
> Memory behind bridge: f7100000-f72fffff [size=2M]
> Prefetchable memory behind bridge: [disabled]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset-
> FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [88] Subsystem: Super Micro Computer Inc Xeon
> E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller [15d9:0803]
> Capabilities: [80] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: fee00218 Data: 0000
> Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 256 bytes, PhantFunc 0
> ExtTag- RBE+
> DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 256 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr-
> TransPend-
> LnkCap: Port #2, Speed 8GT/s, Width x8, ASPM L0s L1, Exit
> Latency L0s <256ns, L1 <8us
> ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
> LnkCtl: ASPM L0s Enabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s (downgraded), Width x1 (downgraded)
> TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
> Surprise-
> Slot #1, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
> HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
> Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCap: CRSVisible-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
> PMEIntEna- CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-
> NROPrPrP- LTR+
> 10BitTagComp- 10BitTagReq- OBFF Via WAKE#,
> ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS- LN System CLS Not Supported, TPHComp-
> ExtTPHComp- ARIFwd-
> AtomicOpsCap: Routing- 32bit+ 64bit+ 128bitCAS+
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LTR+ OBFF Via WAKE#, ARIFwd-
> AtomicOpsCtl: ReqEn- EgressBlck-
> LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink-
> Retimer- 2Retimers- DRS-
> LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB,
> EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3-
> LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported
> Capabilities: [100 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128-
> WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [140 v1] Root Complex Link
> Desc: PortNumber=02 ComponentID=01 EltType=Config
> Link0: Desc: TargetPort=00 TargetComponent=01
> AssocRCRB- LinkType=MemMapped LinkValid+
> Addr: 00000000fed19000
> Capabilities: [d94 v1] Secondary PCI Express
> LnkCtl3: LnkEquIntrruptEn- PerformEqu-
> LaneErrStat: 0
> Kernel driver in use: pcieport
>
> 00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series
> Chipset Family USB xHCI [8086:8c31] (rev 05) (prog-if 30 [XHCI])
> Subsystem: Super Micro Computer Inc 8 Series/C220 Series Chipset
> Family USB xHCI [15d9:0803]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 36
> IOMMU group: 2
> Region 0: Memory at f7500000 (64-bit, non-prefetchable) [size=64K]
> Capabilities: [70] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
> Address: 00000000fee003d8 Data: 0000
> Kernel driver in use: xhci_hcd
> Kernel modules: xhci_pci
>
> 00:16.0 Communication controller [0780]: Intel Corporation 8 Series/C220
> Series Chipset Family MEI Controller #1 [8086:8c3a] (rev 04)
> Subsystem: Super Micro Computer Inc 8 Series/C220 Series Chipset
> Family MEI Controller [15d9:0803]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> IOMMU group: 3
> Region 0: Memory at f7517000 (64-bit, non-prefetchable) [size=16]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Kernel modules: mei_me
>
> 00:16.1 Communication controller [0780]: Intel Corporation 8 Series/C220
> Series Chipset Family MEI Controller #2 [8086:8c3b] (rev 04)
> Subsystem: Super Micro Computer Inc 8 Series/C220 Series Chipset
> Family MEI Controller [15d9:0803]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 10
> IOMMU group: 3
> Region 0: Memory at f7516000 (64-bit, non-prefetchable) [size=16]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
>
> 00:1a.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series
> Chipset Family USB EHCI #2 [8086:8c2d] (rev 05) (prog-if 20 [EHCI])
> Subsystem: Super Micro Computer Inc 8 Series/C220 Series Chipset
> Family USB EHCI [15d9:0803]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 4
> Region 0: Memory at f7514000 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Debug port: BAR=1 offset=00a0
> Capabilities: [98] PCI Advanced Features
> AFCap: TP+ FLR+
> AFCtrl: FLR-
> AFStatus: TP-
> Kernel driver in use: ehci-pci
> Kernel modules: ehci_pci
>
> 00:1c.0 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset
> Family PCI Express Root Port #1 [8086:8c10] (rev d5) (prog-if 00 [Normal
> decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 26
> IOMMU group: 5
> Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
> I/O behind bridge: 0000e000-0000efff [size=4K]
> Memory behind bridge: f6000000-f70fffff [size=17M]
> Prefetchable memory behind bridge: [disabled]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16+ MAbort- >Reset-
> FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag- RBE+
> DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+
> TransPend-
> LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit
> Latency L0s <512ns, L1 <16us
> ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
> LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
> Surprise-
> Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
> HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
> Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCap: CRSVisible-
> RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+
> PMEIntEna- CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABC, TimeoutDis+
> NROPrPrP- LTR+
> 10BitTagComp- 10BitTagReq- OBFF Not Supported,
> ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS- LN System CLS Not Supported, TPHComp-
> ExtTPHComp- ARIFwd-
> AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LTR+ OBFF Disabled, ARIFwd-
> AtomicOpsCtl: ReqEn- EgressBlck-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB,
> EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3-
> LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported
> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: fee00238 Data: 0000
> Capabilities: [90] Subsystem: Super Micro Computer Inc 8
> Series/C220 Series Chipset Family PCI Express Root Port [15d9:0803]
> Capabilities: [a0] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: pcieport
>
> 00:1c.2 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset
> Family PCI Express Root Port #3 [8086:8c14] (rev d5) (prog-if 00 [Normal
> decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin C routed to IRQ 27
> IOMMU group: 6
> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
> I/O behind bridge: 0000d000-0000dfff [size=4K]
> Memory behind bridge: f7400000-f74fffff [size=1M]
> Prefetchable memory behind bridge: [disabled]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset-
> FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag- RBE+
> DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+
> TransPend-
> LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Exit
> Latency L0s <512ns, L1 <16us
> ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
> Surprise-
> Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
> HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
> Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCap: CRSVisible-
> RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+
> PMEIntEna- CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABC, TimeoutDis+
> NROPrPrP- LTR+
> 10BitTagComp- 10BitTagReq- OBFF Not Supported,
> ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS- LN System CLS Not Supported, TPHComp-
> ExtTPHComp- ARIFwd-
> AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LTR+ OBFF Disabled, ARIFwd-
> AtomicOpsCtl: ReqEn- EgressBlck-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB,
> EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3-
> LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported
> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: fee00278 Data: 0000
> Capabilities: [90] Subsystem: Super Micro Computer Inc 8
> Series/C220 Series Chipset Family PCI Express Root Port [15d9:0803]
> Capabilities: [a0] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: pcieport
>
> 00:1c.3 PCI bridge [0604]: Intel Corporation 8 Series/C220 Series Chipset
> Family PCI Express Root Port #4 [8086:8c16] (rev d5) (prog-if 00 [Normal
> decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin D routed to IRQ 28
> IOMMU group: 7
> Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
> I/O behind bridge: 0000c000-0000cfff [size=4K]
> Memory behind bridge: f7300000-f73fffff [size=1M]
> Prefetchable memory behind bridge: [disabled]
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset-
> FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag- RBE+
> DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+
> TransPend-
> LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Exit
> Latency L0s <512ns, L1 <16us
> ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp-
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
> Surprise-
> Slot #3, PowerLimit 10.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
> HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
> Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCap: CRSVisible-
> RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+
> PMEIntEna- CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABC, TimeoutDis+
> NROPrPrP- LTR+
> 10BitTagComp- 10BitTagReq- OBFF Not Supported,
> ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS- LN System CLS Not Supported, TPHComp-
> ExtTPHComp- ARIFwd-
> AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LTR+ OBFF Disabled, ARIFwd-
> AtomicOpsCtl: ReqEn- EgressBlck-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB,
> EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3-
> LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported
> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: fee002b8 Data: 0000
> Capabilities: [90] Subsystem: Super Micro Computer Inc 8
> Series/C220 Series Chipset Family PCI Express Root Port [15d9:0803]
> Capabilities: [a0] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: pcieport
>
> 00:1d.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series
> Chipset Family USB EHCI #1 [8086:8c26] (rev 05) (prog-if 20 [EHCI])
> Subsystem: Super Micro Computer Inc 8 Series/C220 Series Chipset
> Family USB EHCI [15d9:0803]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 22
> IOMMU group: 8
> Region 0: Memory at f7513000 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Debug port: BAR=1 offset=00a0
> Capabilities: [98] PCI Advanced Features
> AFCap: TP+ FLR+
> AFCtrl: FLR-
> AFStatus: TP-
> Kernel driver in use: ehci-pci
> Kernel modules: ehci_pci
>
> 00:1f.0 ISA bridge [0601]: Intel Corporation C224 Series Chipset Family
> Server Standard SKU LPC Controller [8086:8c54] (rev 05)
> Subsystem: Super Micro Computer Inc C224 Series Chipset Family
> Server Standard SKU LPC Controller [15d9:0803]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> IOMMU group: 9
> Capabilities: [e0] Vendor Specific Information: Len=0c <?>
> Kernel driver in use: lpc_ich
> Kernel modules: lpc_ich
>
> 00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series
> Chipset Family 6-port SATA Controller 1 [AHCI mode] [8086:8c02] (rev 05)
> (prog-if 01 [AHCI 1.0])
> Subsystem: Super Micro Computer Inc 8 Series/C220 Series Chipset
> Family 6-port SATA Controller 1 [AHCI mode] [15d9:0803]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 34
> IOMMU group: 9
> Region 0: I/O ports at f050 [size=8]
> Region 1: I/O ports at f040 [size=4]
> Region 2: I/O ports at f030 [size=8]
> Region 3: I/O ports at f020 [size=4]
> Region 4: I/O ports at f000 [size=32]
> Region 5: Memory at f7512000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: fee00378 Data: 0000
> Capabilities: [70] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
> Kernel driver in use: ahci
> Kernel modules: ahci
>
> 00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset
> Family SMBus Controller [8086:8c22] (rev 05)
> Subsystem: Super Micro Computer Inc 8 Series/C220 Series Chipset
> Family SMBus Controller [15d9:0803]
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin C routed to IRQ 18
> IOMMU group: 9
> Region 0: Memory at f7511000 (64-bit, non-prefetchable) [size=256]
> Region 4: I/O ports at 0580 [size=32]
> Kernel driver in use: i801_smbus
> Kernel modules: i2c_i801
>
> 00:1f.6 Signal processing controller [1180]: Intel Corporation 8 Series
> Chipset Family Thermal Management Controller [8086:8c24] (rev 05)
> Subsystem: Super Micro Computer Inc 8 Series Chipset Family
> Thermal Management Controller [15d9:0803]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin C routed to IRQ 18
> IOMMU group: 9
> Region 0: Memory at f7510000 (64-bit, non-prefetchable) [size=4K]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
> Address: 00000000 Data: 0000
> Kernel driver in use: intel_pch_thermal
> Kernel modules: intel_pch_thermal
>
> 01:00.0 RAID bus controller [0104]: Adaptec Series 6 - 6G SAS/PCIe 2
> [9005:028b] (rev 01)
> Subsystem: Adaptec Series 6 Entry Level - ASR-6405E - 4 internal
> 6G SAS ports [9005:0200]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 35
> IOMMU group: 1
> Region 0: Memory at f7100000 (64-bit, non-prefetchable) [size=1M]
> Region 2: Memory at f7241000 (64-bit, non-prefetchable) [size=2K]
> Region 4: Memory at f7240000 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at f7200000 [disabled] [size=256K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee00398 Data: 0000
> Capabilities: [70] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
> <1us, L1 <8us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> SlotPowerLimit 253.000W
> DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 256 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr-
> TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s L1, Exit
> Latency L0s <512ns, L1 <64us
> ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
> LnkCtl: ASPM L0s Enabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s (ok), Width x1 (downgraded)
> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+
> NROPrPrP- LTR-
> 10BitTagComp- 10BitTagReq- OBFF Not Supported,
> ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS- TPHComp- ExtTPHComp-
> AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LTR- OBFF Disabled,
> AtomicOpsCtl: ReqEn-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB,
> EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3-
> LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported
> Capabilities: [ac] MSI-X: Enable- Count=16 Masked-
> Vector table: BAR=0 offset=001c2000
> PBA: BAR=0 offset=001c4000
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP- BadDLLP+ Rollover- Timeout+
> AdvNonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> AdvNonFatalErr+
> AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn-
> ECRCChkCap+ ECRCChkEn-
> MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
> HeaderLog: 00000000 00000000 00000000 00000000
> Kernel driver in use: aacraid
> Kernel modules: aacraid
>
> 02:00.0 PCI bridge [0604]: ASPEED Technology, Inc. AST1150 PCI-to-PCI
> Bridge [1a03:1150] (rev 03) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> IOMMU group: 10
> Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
> I/O behind bridge: 0000e000-0000efff [size=4K]
> Memory behind bridge: f6000000-f70fffff [size=17M]
> Prefetchable memory behind bridge: [disabled]
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA+ VGA16+ MAbort- >Reset-
> FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [78] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [80] Express (v1) PCI-Express to PCI/PCI-X Bridge,
> MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ AttnBtn- AttnInd- PwrInd- RBE-
> SlotPowerLimit 10.000W
> DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq-
> RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
> BrConfRtry-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+
> TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Exit Latency L0s <2us, L1 <16us
> ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
> LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> Capabilities: [a4] Subsystem: Super Micro Computer Inc AST1150
> PCI-to-PCI Bridge [15d9:0803]
> Capabilities: [100 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
> WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
> Status: NegoPending- InProgress-
> Capabilities: [800 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> AdvNonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> AdvNonFatalErr+
> AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn-
> ECRCChkCap- ECRCChkEn-
> MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
> HeaderLog: 00000000 00000000 00000000 00000000
>
> 03:00.0 VGA compatible controller [0300]: ASPEED Technology, Inc. ASPEED
> Graphics Family [1a03:2000] (rev 30) (prog-if 00 [VGA controller])
> DeviceName: Onboard VGA
> Subsystem: Super Micro Computer Inc ASPEED Graphics Family
> [15d9:0803]
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 16
> IOMMU group: 10
> Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at f7000000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at e000 [size=128]
> Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable- Count=1/4 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Kernel driver in use: ast
> Kernel modules: ast
>
> 04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network
> Connection [8086:1533] (rev 03)
> DeviceName: Onboard LAN1
> Subsystem: Super Micro Computer Inc I210 Gigabit Network
> Connection [15d9:1533]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 18
> IOMMU group: 11
> Region 0: Memory at f7400000 (32-bit, non-prefetchable) [size=512K]
> Region 2: I/O ports at d000 [size=32]
> Region 3: Memory at f7480000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
> Address: 0000000000000000 Data: 0000
> Masking: 00000000 Pending: 00000000
> Capabilities: [70] MSI-X: Enable+ Count=5 Masked-
> Vector table: BAR=3 offset=00000000
> PBA: BAR=3 offset=00002000
> Capabilities: [a0] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s
> <512ns, L1 <64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
> SlotPowerLimit 0.000W
> DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> FLReset-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+
> TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Exit Latency L0s <2us, L1 <16us
> ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
> NROPrPrP- LTR-
> 10BitTagComp- 10BitTagReq- OBFF Not Supported,
> ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS- TPHComp- ExtTPHComp-
> AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LTR- OBFF Disabled,
> AtomicOpsCtl: ReqEn-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB,
> EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3-
> LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported
> Capabilities: [100 v2] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> AdvNonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> AdvNonFatalErr+
> AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn-
> ECRCChkCap+ ECRCChkEn-
> MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
> HeaderLog: 00000000 00000000 00000000 00000000
> Capabilities: [140 v1] Device Serial Number 00-25-90-ff-ff-db-88-8c
> Capabilities: [1a0 v1] Transaction Processing Hints
> Device specific mode supported
> Steering table in TPH capability structure
> Kernel driver in use: igb
> Kernel modules: igb
>
> 05:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network
> Connection [8086:1533] (rev 03)
> DeviceName: Onboard LAN2
> Subsystem: Super Micro Computer Inc I210 Gigabit Network
> Connection [15d9:1533]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 19
> IOMMU group: 12
> Region 0: Memory at f7300000 (32-bit, non-prefetchable) [size=512K]
> Region 2: I/O ports at c000 [size=32]
> Region 3: Memory at f7380000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
> Address: 0000000000000000 Data: 0000
> Masking: 00000000 Pending: 00000000
> Capabilities: [70] MSI-X: Enable+ Count=5 Masked-
> Vector table: BAR=3 offset=00000000
> PBA: BAR=3 offset=00002000
> Capabilities: [a0] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s
> <512ns, L1 <64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
> SlotPowerLimit 0.000W
> DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> FLReset-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+
> TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Exit Latency L0s <2us, L1 <16us
> ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
> TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
> NROPrPrP- LTR-
> 10BitTagComp- 10BitTagReq- OBFF Not Supported,
> ExtFmt- EETLPPrefix-
> EmergencyPowerReduction Not Supported,
> EmergencyPowerReductionInit-
> FRS- TPHComp- ExtTPHComp-
> AtomicOpsCap: 32bit- 64bit- 128bitCAS-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LTR- OBFF Disabled,
> AtomicOpsCtl: ReqEn-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB,
> EqualizationComplete- EqualizationPhase1-
> EqualizationPhase2- EqualizationPhase3-
> LinkEqualizationRequest-
> Retimer- 2Retimers- CrosslinkRes: unsupported
> Capabilities: [100 v2] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> AdvNonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> AdvNonFatalErr+
> AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn-
> ECRCChkCap+ ECRCChkEn-
> MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
> HeaderLog: 00000000 00000000 00000000 00000000
> Capabilities: [140 v1] Device Serial Number 00-25-90-ff-ff-db-88-8d
> Capabilities: [1a0 v1] Transaction Processing Hints
> Device specific mode supported
> Steering table in TPH capability structure
> Kernel driver in use: igb
> Kernel modules: igb
>
>
> ** USB devices:
> Bus 003 Device 002: ID 8087:8000 Intel Corp. Integrated Rate Matching Hub
> Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 001 Device 002: ID 8087:8008 Intel Corp. Integrated Rate Matching Hub
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
> Bus 002 Device 003: ID 0557:2419 ATEN International Co., Ltd
> Bus 002 Device 002: ID 0557:7000 ATEN International Co., Ltd Hub
> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>
>
> -- System Information:
> Debian Release: 11.6
> APT prefers stable-updates
> APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500,
> 'stable')
> Architecture: amd64 (x86_64)
>
> Kernel: Linux 5.10.0-20-amd64 (SMP w/8 CPU threads)
> Kernel taint flags: TAINT_PROPRIETARY_MODULE, TAINT_OOT_MODULE,
> TAINT_UNSIGNED_MODULE
> Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) (ignored:
> LC_ALL set to en_US.UTF-8), LANGUAGE not set
> Shell: /bin/sh linked to /usr/bin/dash
> Init: systemd (via /run/systemd/system)
> LSM: AppArmor: enabled
>
> Versions of packages linux-image-5.10.0-20-amd64 depends on:
> ii initramfs-tools [linux-initramfs-tool] 0.140
> ii kmod 28-1
> ii linux-base 4.6
>
> Versions of packages linux-image-5.10.0-20-amd64 recommends:
> ii apparmor 2.13.6-10
> ii firmware-linux-free 20200122-1
>
> Versions of packages linux-image-5.10.0-20-amd64 suggests:
> pn debian-kernel-handbook <none>
> ii grub-pc 2.06-3~deb11u5
> pn linux-doc-5.10 <none>
>
> Versions of packages linux-image-5.10.0-20-amd64 is related to:
> ii firmware-amd-graphics 20210315-3
> pn firmware-atheros <none>
> pn firmware-bnx2 <none>
> pn firmware-bnx2x <none>
> pn firmware-brcm80211 <none>
> pn firmware-cavium <none>
> pn firmware-intel-sound <none>
> pn firmware-intelwimax <none>
> pn firmware-ipw2x00 <none>
> pn firmware-ivtv <none>
> pn firmware-iwlwifi <none>
> pn firmware-libertas <none>
> ii firmware-linux-nonfree 20210315-3
> ii firmware-misc-nonfree 20210315-3
> pn firmware-myricom <none>
> pn firmware-netxen <none>
> pn firmware-qlogic <none>
> pn firmware-realtek <none>
> pn firmware-samsung <none>
> pn firmware-siano <none>
> pn firmware-ti-connectivity <none>
> pn xen-hypervisor <none>
>
> -- no debconf information
>
>
