Hi Damien, Damien Le Moal wrote: > > Ok, did another one, this time with "debug loglevel=7" added on the > > kernel commandline by editing it in GRUB: > > > > https://noone.org/debian/Bug-Reports/1006149/DSCN5259.MOV > > Thanks for this. But unfortunately, it does not tell us much as to what > is going on...
Ah, what a pity. Thanks for having a look anyways. > Could you send me dmesg output of a clean boot with 5.15 > kernel ? Sure. I already posted this to the Debian bug report at https://bugs.debian.org/cgi-bin/bugreport.cgi?att=2;bug=1006149;filename=5.15.15-2.dmesg.xz;msg=96 shortly before you got into the loop. > Also, once booted in 5.15, install sg3utils and run these commands: > > sudo sg_sat_read_gplog --log=0 --page=0 /dev/sdX > sudo sg_sat_read_gplog --log=0 --page=0 --dma /dev/sdX [I find it disturbing how often people just prepend "sudo" in instructions when they actually mean "as root". Not everyone has sudo installed — usually for good reasons.] # sg_sat_read_gplog --log=0 --page=0 /dev/sda 00 0001 0000 0000 0002 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 08 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 10 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 18 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 20 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 28 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 30 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 38 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 40 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 48 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 50 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 58 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 60 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 68 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 70 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 78 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 80 0010 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 88 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 90 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. 98 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. a0 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. a8 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. b0 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. b8 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. c0 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. c8 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. d0 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. d8 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. e0 0001 0001 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. e8 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. f0 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. f8 0000 0000 0000 0000 0000 0000 0000 0000 .. .. .. .. .. .. .. .. # sg_sat_read_gplog --log=0 --page=0 --dma /dev/sda ATA PASS-THROUGH (16), bad field in cdb sg_sat_read_gplog failed: Illegal request # Since the last output might be a hardware-specific issue, here some more information on /dev/sda: # fdisk -l /dev/sda Disk /dev/sda: 149.05 GiB, 160041885696 bytes, 312581808 sectors Disk model: SAMSUNG HM160HC Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x000500cc Device Boot Start End Sectors Size Id Type /dev/sda1 * 63 993279 993217 485M 83 Linux /dev/sda3 996030 2988089 1992060 972.7M 82 Linux swap / Solaris /dev/sda4 2988090 312576704 309588615 147.6G 5 Extended /dev/sda5 2988153 86874232 83886080 40G 83 Linux # smartctl --info /dev/sda smartctl 7.2 2020-12-30 r5155 [i686-linux-5.15.0-3-686-pae] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M5 Device Model: SAMSUNG HM160HC Serial Number: S12TJD0SA62821 LU WWN Device Id: 5 0f0000 003162821 Firmware Version: LQ100-10 User Capacity: 160’041’885’696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ATA/ATAPI-7 T13/1532D revision 0 Transport Type: Parallel, Unknown (0x00f) Local Time is: Wed Mar 9 15:25:44 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled HTH. Regards, Axel -- ,''`. | Axel Beckert <a...@debian.org>, https://people.debian.org/~abe/ : :' : | Debian Developer, ftp.ch.debian.org Admin `. `' | 4096R: 2517 B724 C5F6 CA99 5329 6E61 2FF9 CD59 6126 16B5 `- | 1024D: F067 EA27 26B9 C3FC 1486 202E C09E 1D89 9593 0EDE
