--- Begin Message ---
Package: linux-2.6
Version: 2.6.32-28
Severity: grave
Tags: upstream
Justification: causes non-serious data loss
Hello All,
I just finish a fresh install of debian squeeze with debian-test1 CD and after
boot I get several Warning :
[ 1.899239] scsi 0:2:0:0: Direct-Access LSI RAID 5/6 SAS 6G 2.40
PQ: 0 ANSI: 5
[ 1.910643] sd 0:2:0:0: [sda] 4677218560 512-byte logical blocks: (2.39
TB/2.17 TiB)
[ 1.910718] sd 0:2:0:0: [sda] Write Protect is off
[ 1.910722] sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
[ 1.910759] sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.910919] sda:
[ 1.911236] ------------[ cut here ]------------
[ 1.911248] WARNING: at
/build/buildd-linux-2.6_2.6.32-28-amd64-EUJiNq/linux-2.6-2.6.32/debian/build/source_amd64_none/fs/sysfs/dir.c:491
sysfs_add_one+0xcc/0xe4()
[ 1.911251] Hardware name: PRIMERGY RX300 S6
[ 1.911252] sysfs: cannot create duplicate filename
'/devices/pci0000:00/0000:00:01.0/0000:01:00.0/host0/target0:0:16/0:0:16:0/enclosure/0:0:16:0/ArrayDevice03'
[ 1.911255] Modules linked in: sd_mod ses(+) crc_t10dif enclosure
uhci_hcd(+) ahci(+) mptsas(+) mptscsih libata megaraid_sas igb(+) mptbase
scsi_transport_sas ehci_hcd d
ca thermal usbcore nls_base scsi_mod thermal_sys
[ 1.911277] Pid: 382, comm: modprobe Not tainted 2.6.32-5-amd64 #1
[ 1.911279] Call Trace:
[ 1.911283] [<ffffffff8113f72b>] ? sysfs_add_one+0xcc/0xe4
[ 1.911286] [<ffffffff8113f72b>] ? sysfs_add_one+0xcc/0xe4
[ 1.911291] [<ffffffff8104dd6c>] ? warn_slowpath_common+0x77/0xa3
[ 1.911294] [<ffffffff8104ddf4>] ? warn_slowpath_fmt+0x51/0x59
[ 1.911296] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911299] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911301] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911303] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911306] [<ffffffff8113f72b>] ? sysfs_add_one+0xcc/0xe4
[ 1.911308] [<ffffffff8113fca7>] ? create_dir+0x4f/0x7c
[ 1.911310] [<ffffffff8113fd09>] ? sysfs_create_dir+0x35/0x4a
[ 1.911314] [<ffffffff8118f05b>] ? kobject_get+0x12/0x17
[ 1.911317] [<ffffffff8118f191>] ? kobject_add_internal+0xcb/0x181
[ 1.911319] [<ffffffff8118f3f3>] ? kobject_add+0x74/0x7c
[ 1.911325] [<ffffffff810e7b3d>] ? __kmalloc+0x12f/0x141
[ 1.911329] [<ffffffff8121dc20>] ? device_private_init+0x13/0x45
[ 1.911331] [<ffffffff8121e0c2>] ? device_add+0xce/0x537
[ 1.911335] [<ffffffffa00374d1>] ? enclosure_component_register+0xbe/0xf9
[enclosure]
[ 1.911339] [<ffffffffa007d594>] ? ses_enclosure_data_process+0x18b/0x2a1
[ses]
[ 1.911342] [<ffffffffa007db1b>] ? ses_intf_add+0x331/0x439 [ses]
[ 1.911347] [<ffffffff81220b84>] ? class_interface_register+0x94/0xcf
[ 1.911350] [<ffffffffa008b000>] ? ses_init+0x0/0x35 [ses]
[ 1.911353] [<ffffffffa008b00d>] ? ses_init+0xd/0x35 [ses]
[ 1.911356] [<ffffffff8100a065>] ? do_one_initcall+0x64/0x174
[ 1.911360] [<ffffffff8107a594>] ? sys_init_module+0xc5/0x21a
[ 1.911363] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 1.911365] ---[ end trace 2204c34c56d00ffd ]---
[ 1.911368] kobject_add_internal failed for ArrayDevice03 with -EEXIST,
don't try to register things with the same name in the same directory.
[ 1.911483] Pid: 382, comm: modprobe Tainted: G W 2.6.32-5-amd64 #1
[ 1.911485] Call Trace:
[ 1.911489] [<ffffffff8118f234>] ? kobject_add_internal+0x16e/0x181
[ 1.911492] [<ffffffff8118f3f3>] ? kobject_add+0x74/0x7c
[ 1.911496] [<ffffffff810e7b3d>] ? __kmalloc+0x12f/0x141
[ 1.911499] [<ffffffff8121dc20>] ? device_private_init+0x13/0x45
[ 1.911502] [<ffffffff8121e0c2>] ? device_add+0xce/0x537
[ 1.911505] [<ffffffffa00374d1>] ? enclosure_component_register+0xbe/0xf9
[enclosure]
[ 1.911509] [<ffffffffa007d594>] ? ses_enclosure_data_process+0x18b/0x2a1
[ses]
[ 1.911512] [<ffffffffa007db1b>] ? ses_intf_add+0x331/0x439 [ses]
[ 1.911515] [<ffffffff81220b84>] ? class_interface_register+0x94/0xcf
[ 1.911518] [<ffffffffa008b000>] ? ses_init+0x0/0x35 [ses]
[ 1.911521] [<ffffffffa008b00d>] ? ses_init+0xd/0x35 [ses]
[ 1.911524] [<ffffffff8100a065>] ? do_one_initcall+0x64/0x174
[ 1.911526] [<ffffffff8107a594>] ? sys_init_module+0xc5/0x21a
[ 1.911529] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 1.911536] ------------[ cut here ]------------
[ 1.911539] WARNING: at
/build/buildd-linux-2.6_2.6.32-28-amd64-EUJiNq/linux-2.6-2.6.32/debian/build/source_amd64_none/fs/sysfs/dir.c:491
sysfs_add_one+0xcc/0xe4()
[ 1.911541] Hardware name: PRIMERGY RX300 S6
[ 1.911543] sysfs: cannot create duplicate filename
'/devices/pci0000:00/0000:00:01.0/0000:01:00.0/host0/target0:0:16/0:0:16:0/enclosure/0:0:16:0/ArrayDevice03'
[ 1.911545] Modules linked in: sd_mod ses(+) crc_t10dif enclosure
uhci_hcd(+) ahci(+) mptsas(+) mptscsih libata megaraid_sas igb(+) mptbase
scsi_transport_sas ehci_hcd d
ca thermal usbcore nls_base scsi_mod thermal_sys
[ 1.911556] Pid: 382, comm: modprobe Tainted: G W 2.6.32-5-amd64 #1
[ 1.911557] Call Trace:
[ 1.911559] [<ffffffff8113f72b>] ? sysfs_add_one+0xcc/0xe4
[ 1.911562] [<ffffffff8113f72b>] ? sysfs_add_one+0xcc/0xe4
[ 1.911564] [<ffffffff8104dd6c>] ? warn_slowpath_common+0x77/0xa3
[ 1.911567] [<ffffffff8104ddf4>] ? warn_slowpath_fmt+0x51/0x59
[ 1.911569] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911571] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911574] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911576] [<ffffffff8113f657>] ? sysfs_pathname+0x35/0x3d
[ 1.911578] [<ffffffff8113f72b>] ? sysfs_add_one+0xcc/0xe4
[ 1.911580] [<ffffffff8113fca7>] ? create_dir+0x4f/0x7c
[ 1.911583] [<ffffffff8113fd09>] ? sysfs_create_dir+0x35/0x4a
[ 1.911585] [<ffffffff8118f05b>] ? kobject_get+0x12/0x17
[ 1.911587] [<ffffffff8118f191>] ? kobject_add_internal+0xcb/0x181
[ 1.911590] [<ffffffff8118f3f3>] ? kobject_add+0x74/0x7c
[ 1.911593] [<ffffffff810e7b3d>] ? __kmalloc+0x12f/0x141
[ 1.911596] [<ffffffff8121dc20>] ? device_private_init+0x13/0x45
[ 1.911598] [<ffffffff8121e0c2>] ? device_add+0xce/0x537
[ 1.911601] [<ffffffff810e5711>] ? virt_to_head_page+0x9/0x2a
[ 1.911604] [<ffffffffa00374d1>] ? enclosure_component_register+0xbe/0xf9
[enclosure]
[ 1.911608] [<ffffffffa007d594>] ? ses_enclosure_data_process+0x18b/0x2a1
[ses]
[ 1.911611] [<ffffffffa007db1b>] ? ses_intf_add+0x331/0x439 [ses]
[ 1.911614] [<ffffffff81220b84>] ? class_interface_register+0x94/0xcf
[ 1.911617] [<ffffffffa008b000>] ? ses_init+0x0/0x35 [ses]
[ 1.911620] [<ffffffffa008b00d>] ? ses_init+0xd/0x35 [ses]
[ 1.911622] [<ffffffff8100a065>] ? do_one_initcall+0x64/0x174
[ 1.911625] [<ffffffff8107a594>] ? sys_init_module+0xc5/0x21a
[ 1.911627] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 1.911629] ---[ end trace 2204c34c56d00ffe ]---
[ 1.911631] kobject_add_internal failed for ArrayDevice03 with -EEXIST,
don't try to register things with the same name in the same directory.
[ 1.911745] Pid: 382, comm: modprobe Tainted: G W 2.6.32-5-amd64 #1
[ 1.911747] Call Trace:
[ 1.911751] [<ffffffff8118f234>] ? kobject_add_internal+0x16e/0x181
[ 1.911754] [<ffffffff8118f3f3>] ? kobject_add+0x74/0x7c
[ 1.911758] [<ffffffff810e7b3d>] ? __kmalloc+0x12f/0x141
[ 1.911761] [<ffffffff8121dc20>] ? device_private_init+0x13/0x45
[ 1.911764] [<ffffffff8121e0c2>] ? device_add+0xce/0x537
[ 1.911766] [<ffffffff810e5711>] ? virt_to_head_page+0x9/0x2a
[ 1.911770] [<ffffffffa00374d1>] ? enclosure_component_register+0xbe/0xf9
[enclosure]
[ 1.911773] [<ffffffffa007d594>] ? ses_enclosure_data_process+0x18b/0x2a1
[ses]
[ 1.911776] [<ffffffffa007db1b>] ? ses_intf_add+0x331/0x439 [ses]
[ 1.911780] [<ffffffff81220b84>] ? class_interface_register+0x94/0xcf
[ 1.911783] [<ffffffffa008b000>] ? ses_init+0x0/0x35 [ses]
[ 1.911786] [<ffffffffa008b00d>] ? ses_init+0xd/0x35 [ses]
[ 1.911788] [<ffffffff8100a065>] ? do_one_initcall+0x64/0x174
[ 1.911791] [<ffffffff8107a594>] ? sys_init_module+0xc5/0x21a
[ 1.911793] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
This error concern the LSI SAS card (or maybe my disks), for the moment I don't
see any incidence on my data (I will do backups more frequently :p)
Thank you all for the good work, keep up with it !
Grégory
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-28) (b...@decadent.org.uk) (gcc
version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Nov 25 18:02:11 UTC 2010
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-amd64 root=/dev/mapper/srv--kiestra--sto1-root ro
quiet
** Tainted: W (512)
* Taint on warning.
** Kernel log:
[ 2.061455] alloc kstat_irqs on node -1
[ 2.061457] igb 0000:08:00.1: irq 72 for MSI/MSI-X
[ 2.061459] alloc irq_desc for 73 on node -1
[ 2.061460] alloc kstat_irqs on node -1
[ 2.061463] igb 0000:08:00.1: irq 73 for MSI/MSI-X
[ 2.061464] alloc irq_desc for 74 on node -1
[ 2.061466] alloc kstat_irqs on node -1
[ 2.061468] igb 0000:08:00.1: irq 74 for MSI/MSI-X
[ 2.061470] alloc irq_desc for 75 on node -1
[ 2.061471] alloc kstat_irqs on node -1
[ 2.061474] igb 0000:08:00.1: irq 75 for MSI/MSI-X
[ 2.244757] igb 0000:08:00.1: Intel(R) Gigabit Ethernet Network Connection
[ 2.244760] igb 0000:08:00.1: eth1: (PCIe:2.5Gb/s:Width x4) 00:19:99:97:a7:43
[ 2.244842] igb 0000:08:00.1: eth1: PBA No: 313130-032
[ 2.244844] igb 0000:08:00.1: Using MSI-X interrupts. 4 rx queue(s), 4 tx
queue(s)
[ 2.253505] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.253527] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.253668] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.253688] ata6: SATA link down (SStatus 0 SControl 300)
[ 2.254835] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.254852] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.255304] ata1.00: ATAPI: Optiarc DVD RW AD-7700S, 1.44, max UDMA/100
[ 2.261961] ata1.00: configured for UDMA/100
[ 2.277852] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7700S 1.44
PQ: 0 ANSI: 5
[ 2.298774] usb 1-6: new high speed USB device using ehci_hcd and address 3
[ 2.320296] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda
tray
[ 2.320299] Uniform CD-ROM driver Revision: 3.20
[ 2.320375] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.322739] ses 0:0:16:0: Attached scsi generic sg0 type 13
[ 2.322764] sd 0:2:0:0: Attached scsi generic sg1 type 0
[ 2.322788] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 2.435453] usb 1-6: New USB device found, idVendor=0000, idProduct=0000
[ 2.435457] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.435460] usb 1-6: Product: iRMC USB Device
[ 2.435462] usb 1-6: Manufacturer: Fujitsu
[ 2.435464] usb 1-6: SerialNumber: C01944414E0304
[ 2.435525] usb 1-6: configuration #1 chosen from 1 choice
[ 2.439992] Initializing USB Mass Storage driver...
[ 2.440071] scsi7 : SCSI emulation for USB Mass Storage devices
[ 2.440127] usb-storage: device found at 3
[ 2.440128] usb-storage: waiting for device to settle before scanning
[ 2.440137] usbcore: registered new interface driver usb-storage
[ 2.440139] USB Mass Storage support registered.
[ 2.441388] ioc0: LSISAS1068E B3: Capabilities={Initiator}
[ 2.441410] mptsas 0000:03:00.0: setting latency timer to 64
[ 2.672881] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 2.836941] usb 5-1: New USB device found, idVendor=0000, idProduct=0000
[ 2.836944] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.836947] usb 5-1: Product: iRMC USB Device
[ 2.836949] usb 5-1: Manufacturer: Fujitsu
[ 2.836950] usb 5-1: SerialNumber: 401944414E0304
[ 2.837014] usb 5-1: configuration #1 chosen from 1 choice
[ 2.845803] usbcore: registered new interface driver hiddev
[ 2.850095] input: Fujitsu iRMC USB Device as
/devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1:1.0/input/input1
[ 2.850135] generic-usb 0003:0000:0000.0001: input,hidraw0: USB HID v1.11
Keyboard [Fujitsu iRMC USB Device] on usb-0000:00:1a.2-1/input0
[ 2.854041] input: Fujitsu iRMC USB Device as
/devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1:1.1/input/input2
[ 2.854101] generic-usb 0003:0000:0000.0002: input,hidraw1: USB HID v1.11
Mouse [Fujitsu iRMC USB Device] on usb-0000:00:1a.2-1/input1
[ 2.854124] usbcore: registered new interface driver usbhid
[ 2.854127] usbhid: v2.6:USB HID core driver
[ 7.430064] usb-storage: device scan complete
[ 7.432804] scsi 7:0:0:0: CD-ROM Fujitsu Remote Iso CDROM 2.04
PQ: 0 ANSI: 0
[ 7.437781] sr1: scsi3-mmc drive: 0x/0x tray
[ 7.437855] sr 7:0:0:0: Attached scsi CD-ROM sr1
[ 7.437902] sr 7:0:0:0: Attached scsi generic sg3 type 5
[ 15.447956] scsi8 : ioc0: LSISAS1068E B3, FwRev=011b2900h, Ports=1,
MaxQ=483, IRQ=26
[ 15.555090] device-mapper: uevent: version 1.0.3
[ 15.555177] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised:
dm-de...@redhat.com
[ 15.738813] kjournald starting. Commit interval 5 seconds
[ 15.738819] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.722948] udev[530]: starting version 164
[ 16.917653] processor LNXCPU:00: registered as cooling_device0
[ 16.917779] processor LNXCPU:01: registered as cooling_device1
[ 16.917895] processor LNXCPU:02: registered as cooling_device2
[ 16.918039] processor LNXCPU:03: registered as cooling_device3
[ 16.918156] processor LNXCPU:04: registered as cooling_device4
[ 16.918277] processor LNXCPU:05: registered as cooling_device5
[ 16.918437] processor LNXCPU:08: registered as cooling_device6
[ 16.918559] processor LNXCPU:09: registered as cooling_device7
[ 16.918676] processor LNXCPU:0a: registered as cooling_device8
[ 16.918797] processor LNXCPU:0b: registered as cooling_device9
[ 16.918925] processor LNXCPU:0c: registered as cooling_device10
[ 16.919046] processor LNXCPU:0d: registered as cooling_device11
[ 16.926279] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 16.926314] ACPI: Power Button [PWRB]
[ 16.926363] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 16.926384] ACPI: Power Button [PWRF]
[ 16.931382] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 16.932047] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ
17
[ 17.149866] Error: Driver 'pcspkr' is already registered, aborting...
[ 17.481552] power_meter ACPI000D:00: Found ACPI power meter.
[ 17.481576] ACPI Warning for \_SB_.SPM_._PMD: Return Package type mismatch
at index 0 - found String, expected Reference (20090903/nspredef-1012)
[ 17.481684] ACPI: AC Adapter [PSD] (on-line)
[ 17.850844] EXT3 FS on dm-0, internal journal
[ 17.905104] loop: module loaded
[ 18.339278] Adding 7917560k swap on /dev/mapper/srv--kiestra--sto1-swap_1.
Priority:-1 extents:1 across:7917560k
[ 19.420733] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.420810] igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
RX/TX
[ 19.421397] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 30.156509] eth0: no IPv6 routers present
[ 3472.537477] usb 5-1: USB disconnect, address 2
** Model information
sys_vendor: FUJITSU
product_name: PRIMERGY RX300 S6
product_version: GS01
chassis_vendor: FUJITSU
chassis_version: RX300S6R3
bios_vendor: FUJITSU // Phoenix Technologies Ltd.
bios_version: 6.00 Rev. 1.08.2619.N1
board_vendor: FUJITSU
board_name: D2619
board_version: S26361-D2619-N15 WGS10 GS02
** Loaded modules:
Module Size Used by
ext2 52969 1
loop 11799 0
snd_pcm 60503 0
snd_timer 15582 1 snd_pcm
snd 46446 2 snd_pcm,snd_timer
soundcore 4598 1 snd
snd_page_alloc 6249 1 snd_pcm
i2c_i801 7830 0
pcspkr 1699 0
container 2389 0
ac 2192 0
power_meter 8302 0
button 4650 0
evdev 7352 2
i2c_core 15712 1 i2c_i801
processor 29935 12
ext3 106518 1
jbd 37085 1 ext3
mbcache 5050 2 ext2,ext3
dm_mod 53770 6
usbhid 33292 0
hid 63145 1 usbhid
usb_storage 39561 0
sg 18744 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
sd_mod 29889 3
ses 5128 0
crc_t10dif 1276 1 sd_mod
enclosure 5503 1 ses
uhci_hcd 18521 0
ahci 32374 0
mptsas 29188 0
mptscsih 16328 1 mptsas
libata 133616 1 ahci
megaraid_sas 29116 2
igb 77943 0
mptbase 48366 2 mptsas,mptscsih
scsi_transport_sas 19865 1 mptsas
ehci_hcd 31135 0
dca 3761 1 igb
thermal 11674 0
usbcore 122034 5 usbhid,usb_storage,uhci_hcd,ehci_hcd
nls_base 6377 1 usbcore
scsi_mod 122149 10
usb_storage,sg,sr_mod,sd_mod,ses,mptsas,mptscsih,libata,megaraid_sas,scsi_transport_sas
thermal_sys 11942 2 processor,thermal
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet static
address 192.168.85.11
netmask 255.255.255.0
network 192.168.85.0
broadcast 192.168.85.255
gateway 192.168.85.1
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers 172.19.0.2
dns-search labo.ketterthill.lu
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:19:99:97:a7:42 brd ff:ff:ff:ff:ff:ff
inet 192.168.85.11/24 brd 192.168.85.255 scope global eth0
inet6 fe80::219:99ff:fe97:a742/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:19:99:97:a7:43 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 560 8 0 0 0 0 0 0 560
8 0 0 0 0 0 0
eth0:17782606 14377 0 0 0 0 0 0 1007381
7890 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
13908 total packets received
0 forwarded
0 incoming packets discarded
13908 incoming packets delivered
7819 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
26 active connections openings
1 passive connection openings
0 failed connection attempts
6 connection resets received
1 connections established
13892 segments received
7803 segments send out
0 segments retransmited
0 bad segments received.
0 resets sent
Udp:
16 packets received
0 packets to unknown port received.
0 packet receive errors
16 packets sent
UdpLite:
TcpExt:
1 TCP sockets finished time wait in fast timer
9 delayed acks sent
3 packets directly queued to recvmsg prequeue.
1 bytes directly received in process context from prequeue
12324 packet headers predicted
182 acknowledgments not containing data payload received
1642 predicted acknowledgments
IpExt:
InOctets: 17557138
OutOctets: 893373
*** Device features:
eth0: 0x114bb3
eth1: 0x114bb3
lo: 0x13865
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5520 I/O Hub to ESI Port
[8086:3406] (rev 13)
Subsystem: Fujitsu Technology Solutions Device [1734:1127]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Capabilities: [60] MSI: Enable- Count=1/2 Maskable+ 64bit-
Address: 00000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0
Len=00c <?>
00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ce100000-ce1fffff
Prefetchable memory behind bridge: 00000000c0200000-00000000c02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Fujitsu Technology Solutions Device
[1734:1127]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00000 Data: 4089
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #1, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0
Len=00c <?>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Fujitsu Technology Solutions Device
[1734:1127]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00000 Data: 4091
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #7, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0
Len=00c <?>
Kernel driver in use: pcieport
00:05.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI Express Root
Port 5 [8086:340c] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: ce200000-ce5fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Fujitsu Technology Solutions Device
[1734:1127]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00000 Data: 4099
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #6, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Fujitsu Technology Solutions Device
[1734:1127]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00000 Data: 40a1
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #5, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0
Len=00c <?>
Kernel driver in use: pcieport
00:08.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 8 [8086:340f] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Fujitsu Technology Solutions Device
[1734:1127]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00000 Data: 40a9
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #4, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
00:09.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 9 [8086:3410] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Fujitsu Technology Solutions Device
[1734:1127]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00000 Data: 40b1
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #3, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
00:0a.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express
Root Port 10 [8086:3411] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Fujitsu Technology Solutions Device
[1734:1127]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00000 Data: 40b9
Masking: 00000003 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #2, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt+
RxOF+ MalfTLP+ ECRC- UnsupReq+ ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
00:10.0 PIC [0800]: Intel Corporation 5520/5500/X58 Physical and Link Layer
Registers Port 0 [8086:3425] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [50] Vendor Specific Information: Len=ff <?>
00:10.1 PIC [0800]: Intel Corporation 5520/5500/X58 Routing and Protocol Layer
Registers Port 0 [8086:3426] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:11.0 PIC [0800]: Intel Corporation 5520/5500 Physical and Link Layer
Registers Port 1 [8086:3427] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [50] Vendor Specific Information: Len=ff <?>
00:11.1 PIC [0800]: Intel Corporation 5520/5500 Routing & Protocol Layer
Register Port 1 [8086:3428] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:14.0 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub System Management
Registers [8086:342e] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
00:14.1 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch
Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
00:14.2 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Control Status and
RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0
unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
00:14.3 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers
[8086:3438] (rev 13) (prog-if 00 [8259])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:15.0 PIC [0800]: Intel Corporation 5520/5500/X58 Trusted Execution
Technology Registers [8086:342f] (rev 13) (prog-if 20 [IO(X)-APIC])
Subsystem: Device [0034:0027]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:1a.0 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #4 [8086:3a37] (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at 1820 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #5 [8086:3a38] (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1860 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #2 [8086:3a3c] (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at ce000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 1 [8086:3a40] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: ce600000-ce6fffff
Prefetchable memory behind bridge: 00000000c0300000-00000000c04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surprise+
Slot #1, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 40c1
Capabilities: [90] Subsystem: Fujitsu Technology Solutions Device
[1734:114d]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express
Root Port 5 [8086:3a48] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: ce700000-ceffffff
Prefetchable memory behind bridge: 00000000cf000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal- Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surprise+
Slot #5, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 40c9
Capabilities: [90] Subsystem: Fujitsu Technology Solutions Device
[1734:114d]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=05 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1880 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 18a0 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB
UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 18c0 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2
EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ce001000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
90) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Fujitsu Technology Solutions Device
[1734:114d]
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIB (ICH10) LPC Interface
Controller [8086:3a18]
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller [0106]: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller [8086:3a22] (prog-if 01 [AHCI 1.0])
Subsystem: Fujitsu Technology Solutions Device [1734:1150]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 66
Region 0: I/O ports at 1c50 [size=8]
Region 1: I/O ports at 1c44 [size=4]
Region 2: I/O ports at 1c48 [size=8]
Region 3: I/O ports at 1c40 [size=4]
Region 4: I/O ports at 18e0 [size=32]
Region 5: Memory at ce002000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
Address: fee00000 Data: 407a
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
[8086:3a30]
Subsystem: Fujitsu Technology Solutions Device [1734:114d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at ce003000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c00 [size=32]
Kernel driver in use: i801_smbus
01:00.0 RAID bus controller [0104]: LSI Logic / Symbios Logic LSI MegaSAS 9260
[1000:0079] (rev 04)
Subsystem: Fujitsu Technology Solutions RAID Ctrl SAS 6G 5/6 512MB
(D2616) [1734:1176]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at ce100000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at ce180000 (64-bit, non-prefetchable) [size=256K]
[virtual] Expansion ROM at c0200000 [disabled] [size=256K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range BC, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] MSI-X: Enable- Count=15 Masked-
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003800
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [138 v1] Power Budgeting <?>
Kernel driver in use: megaraid_sas
03:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic SAS1068E
PCI-Express Fusion-MPT SAS [1000:0058] (rev 08)
Subsystem: LSI Logic / Symbios Logic Device [1000:3080]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 26
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at ce210000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at ce200000 (64-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at c0000000 [disabled] [size=2M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency
L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [98] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP+ BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: mptsas
08:00.0 Ethernet controller [0200]: Intel Corporation 82575EB Gigabit Network
Connection [8086:10a7] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1128]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ce660000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ce640000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 4000 [size=32]
Region 3: Memory at ce600000 (32-bit, non-prefetchable) [size=16K]
[virtual] Expansion ROM at c0300000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] MSI-X: Enable+ Count=10 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 16ms to 55ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-19-99-ff-ff-97-a7-42
Kernel driver in use: igb
08:00.1 Ethernet controller [0200]: Intel Corporation 82575EB Gigabit Network
Connection [8086:10a7] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1128]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at ce6c0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ce6a0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 4020 [size=32]
Region 3: Memory at ce604000 (32-bit, non-prefetchable) [size=16K]
[virtual] Expansion ROM at c0320000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] MSI-X: Enable+ Count=10 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 16ms to 55ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-19-99-ff-ff-97-a7-42
Kernel driver in use: igb
09:00.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA G200e
[Pilot] ServerEngines (SEP1) [102b:0522] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Fujitsu Technology Solutions Device [1734:108e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at cf000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at ce700000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at ce800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e4] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [54] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
ff:00.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath
Architecture Generic Non-core Registers [8086:2c70] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:00.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath
Architecture System Address Decoder [8086:2d81] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 0
[8086:2d90] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 0
[8086:2d91] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link
0 [8086:2d92] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link
1 [8086:2d93] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 1
[8086:2d94] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.5 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 1
[8086:2d95] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Registers [8086:2d98] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Target Address Decoder [8086:2d99] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller RAS Registers [8086:2d9a] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Test Registers [8086:2d9c] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Control [8086:2da0] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Address [8086:2da1] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Rank [8086:2da2] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 0 Thermal Control [8086:2da3] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Control [8086:2da8] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Address [8086:2da9] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Rank [8086:2daa] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 1 Thermal Control [8086:2dab] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Control [8086:2db0] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Address [8086:2db1] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Rank [8086:2db2] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated
Memory Controller Channel 2 Thermal Control [8086:2db3] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1126]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
** USB devices:
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0000:0000
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/12 CPU cores)
Locale: LANG=fr_LU.UTF-8, LC_CTYPE=fr_LU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs
ii linux-base 2.6.32-28 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
--- End Message ---
