Your message dated Sat, 20 Feb 2021 11:27:46 +0100
with message-id <yddkipl8kluvl...@waldi.eu.org>
and subject line No response by submitter
has caused the Debian Bug report #907637,
regarding bonding with virtio NICs does not work any more
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact ow...@bugs.debian.org
immediately.)
--
907637: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=907637
Debian Bug Tracking System
Contact ow...@bugs.debian.org with problems
--- Begin Message ---
Package: src:linux
Version: 4.9.110-3+deb9u4
Severity: critical
Hi,
For network testing reasons I run several KVM VMs with up to now four virtio
NICs,
where only one NIC is connected and the others are marked as "link_down" in the
KVM configuration.
In the guest the NICs are configured as bonding device with lacp. Up to
linux-image-4.9.0-6-amd64
this worked without issues. Starting with linux-image-4.9.0-7-amd64 the kernel
now reports
after booting:
Aug 27 12:01:39 test-gate-1 kernel: [ 22.881163] bond0: link status up for
interface ens18, enabling it in 0 ms
Aug 27 12:01:39 test-gate-1 kernel: [ 22.882881] bond0: failed to get link
speed/duplex for ens18
Aug 27 12:01:39 test-gate-1 kernel: [ 22.985209] bond0: link status up for
interface ens18, enabling it in 0 ms
Aug 27 12:01:39 test-gate-1 kernel: [ 22.986998] bond0: failed to get link
speed/duplex for ens18
Aug 27 12:01:39 test-gate-1 kernel: [ 23.089250] bond0: link status up for
interface ens18, enabling it in 0 ms
Aug 27 12:01:39 test-gate-1 kernel: [ 23.091765] bond0: failed to get link
speed/duplex for ens18
Aug 27 12:01:40 test-gate-1 kernel: [ 23.193170] bond0: link status up for
interface ens18, enabling it in 0 ms
Aug 27 12:01:40 test-gate-1 kernel: [ 23.195772] bond0: failed to get link
speed/duplex for ens18
ethtool also shows unknown speed and duplex for the virtio interfaces.
This seems to not have been an issue before linux-4.9.0-7.
Switching the virtual NICs from virtio to vmxnet3 solves the issue,
ethtool also reports speed and duplex mode.
I do not know if this is a KVM issue or a kernel issue, but as
the older kernel image works it looks more like a kernel issue to me.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: QEMU
product_name: Standard PC (i440FX + PIIX, 1996)
product_version: pc-i440fx-2.11
chassis_vendor: QEMU
chassis_version: pc-i440fx-2.11
bios_vendor: SeaBIOS
bios_version: rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma]
[8086:1237] (rev 02)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton
II] [8086:7000]
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.1 IDE interface [0101]: Intel Corporation 82371SB PIIX3 IDE
[Natoma/Triton II] [8086:7010] (prog-if 80 [Master])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at e140 [size=16]
Kernel driver in use: ata_piix
Kernel modules: ata_piix, ata_generic
00:01.2 USB controller [0c03]: Intel Corporation 82371SB PIIX3 USB
[Natoma/Triton II] [8086:7020] (rev 01) (prog-if 00 [UHCI])
Subsystem: Red Hat, Inc QEMU Virtual Machine [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e080 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:01.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113]
(rev 03)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Kernel driver in use: piix4_smbus
Kernel modules: i2c_piix4
00:02.0 VGA compatible controller [0300]: Device [1234:1111] (rev 02) (prog-if
00 [VGA controller])
Subsystem: Red Hat, Inc Device [1af4:1100]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fd000000 (32-bit, prefetchable) [size=16M]
Region 2: Memory at feb10000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 000c0000 [disabled] [size=128K]
Kernel driver in use: bochs-drm
Kernel modules: bochs_drm
00:03.0 Unclassified device [00ff]: Red Hat, Inc Virtio memory balloon
[1af4:1002]
Subsystem: Red Hat, Inc Virtio memory balloon [1af4:0005]
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e0a0 [size=32]
Region 4: Memory at fe400000 (64-bit, prefetchable) [size=16K]
Capabilities: [84] Vendor Specific Information: VirtIO: <unknown>
BAR=0 offset=00000000 size=00000000
Capabilities: [70] Vendor Specific Information: VirtIO: Notify
BAR=4 offset=00003000 size=00001000 multiplier=00000004
Capabilities: [60] Vendor Specific Information: VirtIO: DeviceCfg
BAR=4 offset=00002000 size=00001000
Capabilities: [50] Vendor Specific Information: VirtIO: ISR
BAR=4 offset=00001000 size=00001000
Capabilities: [40] Vendor Specific Information: VirtIO: CommonCfg
BAR=4 offset=00000000 size=00001000
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
00:05.0 SCSI storage controller [0100]: Red Hat, Inc Virtio SCSI [1af4:1004]
Subsystem: Red Hat, Inc Virtio SCSI [1af4:0008]
Physical Slot: 5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e000 [size=64]
Region 1: Memory at feb11000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe404000 (64-bit, prefetchable) [size=16K]
Capabilities: [98] MSI-X: Enable+ Count=4 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Capabilities: [84] Vendor Specific Information: VirtIO: <unknown>
BAR=0 offset=00000000 size=00000000
Capabilities: [70] Vendor Specific Information: VirtIO: Notify
BAR=4 offset=00003000 size=00001000 multiplier=00000004
Capabilities: [60] Vendor Specific Information: VirtIO: DeviceCfg
BAR=4 offset=00002000 size=00001000
Capabilities: [50] Vendor Specific Information: VirtIO: ISR
BAR=4 offset=00001000 size=00001000
Capabilities: [40] Vendor Specific Information: VirtIO: CommonCfg
BAR=4 offset=00000000 size=00001000
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
00:08.0 Communication controller [0780]: Red Hat, Inc Virtio console [1af4:1003]
Subsystem: Red Hat, Inc Virtio console [1af4:0003]
Physical Slot: 8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e040 [size=64]
Region 1: Memory at feb12000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe408000 (64-bit, prefetchable) [size=16K]
Capabilities: [98] MSI-X: Enable+ Count=2 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Capabilities: [84] Vendor Specific Information: VirtIO: <unknown>
BAR=0 offset=00000000 size=00000000
Capabilities: [70] Vendor Specific Information: VirtIO: Notify
BAR=4 offset=00003000 size=00001000 multiplier=00000004
Capabilities: [60] Vendor Specific Information: VirtIO: DeviceCfg
BAR=4 offset=00002000 size=00001000
Capabilities: [50] Vendor Specific Information: VirtIO: ISR
BAR=4 offset=00001000 size=00001000
Capabilities: [40] Vendor Specific Information: VirtIO: CommonCfg
BAR=4 offset=00000000 size=00001000
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
00:12.0 Ethernet controller [0200]: Red Hat, Inc Virtio network device
[1af4:1000]
Subsystem: Red Hat, Inc Virtio network device [1af4:0001]
Physical Slot: 18
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e0c0 [size=32]
Region 1: Memory at feb13000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe40c000 (64-bit, prefetchable) [size=16K]
Expansion ROM at fea00000 [disabled] [size=256K]
Capabilities: [98] MSI-X: Enable+ Count=3 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Capabilities: [84] Vendor Specific Information: VirtIO: <unknown>
BAR=0 offset=00000000 size=00000000
Capabilities: [70] Vendor Specific Information: VirtIO: Notify
BAR=4 offset=00003000 size=00001000 multiplier=00000004
Capabilities: [60] Vendor Specific Information: VirtIO: DeviceCfg
BAR=4 offset=00002000 size=00001000
Capabilities: [50] Vendor Specific Information: VirtIO: ISR
BAR=4 offset=00001000 size=00001000
Capabilities: [40] Vendor Specific Information: VirtIO: CommonCfg
BAR=4 offset=00000000 size=00001000
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
00:13.0 Ethernet controller [0200]: Red Hat, Inc Virtio network device
[1af4:1000]
Subsystem: Red Hat, Inc Virtio network device [1af4:0001]
Physical Slot: 19
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e0e0 [size=32]
Region 1: Memory at feb14000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe410000 (64-bit, prefetchable) [size=16K]
Expansion ROM at fea40000 [disabled] [size=256K]
Capabilities: [98] MSI-X: Enable+ Count=3 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Capabilities: [84] Vendor Specific Information: VirtIO: <unknown>
BAR=0 offset=00000000 size=00000000
Capabilities: [70] Vendor Specific Information: VirtIO: Notify
BAR=4 offset=00003000 size=00001000 multiplier=00000004
Capabilities: [60] Vendor Specific Information: VirtIO: DeviceCfg
BAR=4 offset=00002000 size=00001000
Capabilities: [50] Vendor Specific Information: VirtIO: ISR
BAR=4 offset=00001000 size=00001000
Capabilities: [40] Vendor Specific Information: VirtIO: CommonCfg
BAR=4 offset=00000000 size=00001000
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
00:14.0 Ethernet controller [0200]: Red Hat, Inc Virtio network device
[1af4:1000]
Subsystem: Red Hat, Inc Virtio network device [1af4:0001]
Physical Slot: 20
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e100 [size=32]
Region 1: Memory at feb15000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe414000 (64-bit, prefetchable) [size=16K]
Expansion ROM at fea80000 [disabled] [size=256K]
Capabilities: [98] MSI-X: Enable+ Count=3 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Capabilities: [84] Vendor Specific Information: VirtIO: <unknown>
BAR=0 offset=00000000 size=00000000
Capabilities: [70] Vendor Specific Information: VirtIO: Notify
BAR=4 offset=00003000 size=00001000 multiplier=00000004
Capabilities: [60] Vendor Specific Information: VirtIO: DeviceCfg
BAR=4 offset=00002000 size=00001000
Capabilities: [50] Vendor Specific Information: VirtIO: ISR
BAR=4 offset=00001000 size=00001000
Capabilities: [40] Vendor Specific Information: VirtIO: CommonCfg
BAR=4 offset=00000000 size=00001000
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
00:15.0 Ethernet controller [0200]: Red Hat, Inc Virtio network device
[1af4:1000]
Subsystem: Red Hat, Inc Virtio network device [1af4:0001]
Physical Slot: 21
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e120 [size=32]
Region 1: Memory at feb16000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fe418000 (64-bit, prefetchable) [size=16K]
Expansion ROM at feac0000 [disabled] [size=256K]
Capabilities: [98] MSI-X: Enable+ Count=3 Masked-
Vector table: BAR=1 offset=00000000
PBA: BAR=1 offset=00000800
Capabilities: [84] Vendor Specific Information: VirtIO: <unknown>
BAR=0 offset=00000000 size=00000000
Capabilities: [70] Vendor Specific Information: VirtIO: Notify
BAR=4 offset=00003000 size=00001000 multiplier=00000004
Capabilities: [60] Vendor Specific Information: VirtIO: DeviceCfg
BAR=4 offset=00002000 size=00001000
Capabilities: [50] Vendor Specific Information: VirtIO: ISR
BAR=4 offset=00001000 size=00001000
Capabilities: [40] Vendor Specific Information: VirtIO: CommonCfg
BAR=4 offset=00000000 size=00001000
Kernel driver in use: virtio-pci
Kernel modules: virtio_pci
00:1e.0 PCI bridge [0604]: Red Hat, Inc. QEMU PCI-PCI bridge [1b36:0001]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at feb17000 (64-bit, non-prefetchable) [size=256]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe800000-fe9fffff
Prefetchable memory behind bridge: 00000000fe200000-00000000fe3fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [4c] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [48] Slot ID: 0 slots, First+, chassis 01
Capabilities: [40] Hot-plug capable
Kernel modules: shpchp
00:1f.0 PCI bridge [0604]: Red Hat, Inc. QEMU PCI-PCI bridge [1b36:0001]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at feb18000 (64-bit, non-prefetchable) [size=256]
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe600000-fe7fffff
Prefetchable memory behind bridge: 00000000fe000000-00000000fe1fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [4c] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [48] Slot ID: 0 slots, First+, chassis 02
Capabilities: [40] Hot-plug capable
Kernel modules: shpchp
** USB devices:
Bus 001 Device 002: ID 0627:0001 Adomax Technology Co., Ltd
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 9.5
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable'), (150, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 4.9.0-6-amd64 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8),
LANGUAGE=en_US:en (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.9.0-8-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.130
ii kmod 23-2
ii linux-base 4.5
Versions of packages linux-image-4.9.0-8-amd64 recommends:
ii firmware-linux-free 3.4
ii irqbalance 1.1.0-2.3
Versions of packages linux-image-4.9.0-8-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta3-5
pn linux-doc-4.9 <none>
Versions of packages linux-image-4.9.0-8-amd64 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
--- End Message ---
--- Begin Message ---
Hi
I'm closing the bug report as there was no response from submitter.
Regards,
Bastian
--
We do not colonize. We conquer. We rule. There is no other way for us.
-- Rojan, "By Any Other Name", stardate 4657.5
--- End Message ---
