Package: src:linux
Version: 4.19.152-1
Severity: critical
Hi,
with the two latest kernels, linux-image-4.19.0-12-amd64 and
linux-image-4.19.0-11-amd64, my machine does not boot, the reason being
that something with cryptsetup is amiss. I used to be asked for a
passphrase, but using these two kernels, I'm not, and the machine just
cycles trying to find the root partition. I am now running the -10
kernel again, which I would like to get off of. I've tried recovery mode
without any success.
On the console, after dmesg, these three lines repeat ad nauseum:
mdadm: No arrays found in config file or automatically
Volume group "ev0" not found
Cannot process volume group ev0
mdadm: No arrays found in config file or automatically
Volume group "ev0" not found
Cannot process volume group ev0
I think this bug is critical, since I can't get to anything with this
state of the machine.
The disk configuration is pretty straightforward:
git:(master*)$ lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
nvme0n1 259:0 0 953.9G 0 disk
├─nvme0n1p1 259:1 0 238.4M 0 part
├─nvme0n1p2 259:2 0 3.5G 0 part
├─nvme0n1p3 259:3 0 953M 0 part /boot
└─nvme0n1p4 259:4 0 949.2G 0 part
└─nvme0n1p4_crypt 253:0 0 949.2G 0 crypt
├─ev0-swap 253:1 0 29.8G 0 lvm [SWAP]
├─ev0-root 253:2 0 789.4G 0 lvm /
There is one other (data) partition, but that's it for what the system
has.
Cheers,
Toni
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: Dell Inc.
product_name: Precision 5530
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: 1.13.0
board_vendor: Dell Inc.
board_name: 0X78C1
board_version: A02
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 8th Gen Core Processor Host
Bridge/DRAM Registers [8086:3ec4] (rev 07)
Subsystem: Dell 8th Gen Core Processor Host Bridge/DRAM Registers
[1028:087d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: skl_uncore
00:01.0 PCI bridge [0604]: Intel Corporation Skylake PCIe Controller (x16)
[8086:1901] (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: ec000000-ed0fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000d1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation UHD Graphics 630
(Mobile) [8086:3e9b] (prog-if 00 [VGA controller])
Subsystem: Dell UHD Graphics 630 (Mobile) [1028:087d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 154
Region 0: Memory at eb000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 4000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:04.0 Signal processing controller [1180]: Intel Corporation Skylake
Processor Thermal Subsystem [8086:1903] (rev 07)
Subsystem: Dell Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor
Thermal Subsystem [1028:087d]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed510000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: proc_thermal
Kernel modules: processor_thermal_device
00:08.0 System peripheral [0880]: Intel Corporation Skylake Gaussian Mixture
Model [8086:1911]
Subsystem: Dell Xeon E3-1200 v5/v6 / E3-1500 v5 / 6th/7th Gen Core
Processor Gaussian Mixture Model [1028:087d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: Memory at ed528000 (64-bit, non-prefetchable) [disabled]
[size=4K]
Capabilities: <access denied>
00:12.0 Signal processing controller [1180]: Intel Corporation Cannon Lake PCH
Thermal Controller [8086:a379] (rev 10)
Subsystem: Dell Cannon Lake PCH Thermal Controller [1028:087d]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed527000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel_pch_thermal
Kernel modules: intel_pch_thermal
00:14.0 USB controller [0c03]: Intel Corporation Cannon Lake PCH USB 3.1 xHCI
Host Controller [8086:a36d] (rev 10) (prog-if 30 [XHCI])
Subsystem: Dell Cannon Lake PCH USB 3.1 xHCI Host Controller [1028:087d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 130
Region 0: Memory at ed500000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:14.2 RAM memory [0500]: Intel Corporation Cannon Lake PCH Shared SRAM
[8086:a36f] (rev 10)
Subsystem: Dell Cannon Lake PCH Shared SRAM [1028:087d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Region 0: Memory at ed51e000 (64-bit, non-prefetchable) [disabled]
[size=8K]
Region 2: Memory at ed526000 (64-bit, non-prefetchable) [disabled]
[size=4K]
Capabilities: <access denied>
00:15.0 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial
IO I2C Controller [8086:a368] (rev 10)
Subsystem: Dell Cannon Lake PCH Serial IO I2C Controller [1028:087d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 7f800000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.1 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial
IO I2C Controller [8086:a369] (rev 10)
Subsystem: Dell Cannon Lake PCH Serial IO I2C Controller [1028:087d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at 7f801000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:16.0 Communication controller [0780]: Intel Corporation Cannon Lake PCH HECI
Controller [8086:a360] (rev 10)
Subsystem: Dell Cannon Lake PCH HECI Controller [1028:087d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 139
Region 0: Memory at ed523000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:17.0 SATA controller [0106]: Intel Corporation Cannon Lake Mobile PCH SATA
AHCI Controller [8086:a353] (rev 10) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Cannon Lake Mobile PCH SATA AHCI Controller [1028:087d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 129
Region 0: Memory at ed51c000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at ed522000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at 4090 [size=8]
Region 3: I/O ports at 4080 [size=4]
Region 4: I/O ports at 4060 [size=32]
Region 5: Memory at ed521000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1b.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root
Port [8086:a340] (rev f0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 123
Bus: primary=00, secondary=02, subordinate=3a, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: d4000000-ea0fffff
Prefetchable memory behind bridge: 0000000090000000-00000000b1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root
Port [8086:a338] (rev f0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 124
Bus: primary=00, secondary=3b, subordinate=3b, sec-latency=0
Memory behind bridge: ed400000-ed4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root
Port [8086:a33c] (rev f0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 125
Bus: primary=00, secondary=3c, subordinate=3c, sec-latency=0
Memory behind bridge: ed300000-ed3fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root
Port [8086:a330] (rev f0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 126
Bus: primary=00, secondary=3d, subordinate=3d, sec-latency=0
Memory behind bridge: ed200000-ed2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 ISA bridge [0601]: Intel Corporation Device [8086:a30e] (rev 10)
Subsystem: Dell Device [1028:087d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.3 Audio device [0403]: Intel Corporation Cannon Lake PCH cAVS [8086:a348]
(rev 10) (prog-if 80)
Subsystem: Dell Cannon Lake PCH cAVS [1028:087d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 155
Region 0: Memory at ed518000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at ed100000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1f.4 SMBus [0c05]: Intel Corporation Cannon Lake PCH SMBus Controller
[8086:a323] (rev 10)
Subsystem: Dell Cannon Lake PCH SMBus Controller [1028:087d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed520000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
00:1f.5 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH SPI
Controller [8086:a324] (rev 10)
Subsystem: Dell Cannon Lake PCH SPI Controller [1028:087d]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Region 0: Memory at fe010000 (32-bit, non-prefetchable) [size=4K]
01:00.0 3D controller [0302]: NVIDIA Corporation GP107GLM [Quadro P2000 Mobile]
[10de:1cba] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel modules: nvidia
3b:00.0 Network controller [0280]: Intel Corporation Wireless-AC 9260
[8086:2526] (rev 29)
Subsystem: Intel Corporation Wireless-AC 9260 [8086:4010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
3c:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS525A PCI
Express Card Reader [10ec:525a] (rev 01)
Subsystem: Dell RTS525A PCI Express Card Reader [1028:087d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 127
Region 1: Memory at ed300000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: rtsx_pci
Kernel modules: rtsx_pci
3d:00.0 Non-Volatile memory controller [0108]: Toshiba America Info Systems
Device [1179:0116] (prog-if 02 [NVM Express])
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
NUMA node: 0
Region 0: Memory at ed200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: nvme
Kernel modules: nvme
** USB devices:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 046d:c08b Logitech, Inc.
Bus 001 Device 003: ID 0c45:671d Microdia
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 10.6
APT prefers stable
APT policy: (990, 'stable'), (500, 'proposed-updates'), (90, 'testing'), (70,
'unstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.19.0-10-amd64 (SMP w/12 CPU cores)
Kernel taint flags: TAINT_OOT_MODULE, TAINT_UNSIGNED_MODULE
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.utf8 (charmap=UTF-8),
LANGUAGE=en_US:en (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-4.19.0-12-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.133+deb10u1
ii kmod 26-1
ii linux-base 4.6
Versions of packages linux-image-4.19.0-12-amd64 recommends:
ii apparmor 2.13.2-10
ii firmware-linux-free 3.4
Versions of packages linux-image-4.19.0-12-amd64 suggests:
pn debian-kernel-handbook <none>
ii extlinux 3:6.04~git20190206.bf6db5b4+dfsg1-1
ii grub-efi-amd64 2.02+dfsg1-20+deb10u2
pn linux-doc-4.19 <none>
Versions of packages linux-image-4.19.0-12-amd64 is related to:
ii firmware-amd-graphics 20190114-2
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 20190114-2
pn firmware-libertas <none>
ii firmware-linux-nonfree 20190114-2
ii firmware-misc-nonfree 20190114-2
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
