Package: src:linux
Version: 5.6.14-2
Severity: important
Dear Maintainer,
I just updated an Apple PowerBook G4 from debian 8 (latest officially
released version for powerpc) to unstable.
The latest running kernel il 3.16 while the new 5.6.0 does not boot the
machine. While booting, the last lines shown on the screen are:
pmac32_cpufreq: registering PowerMac CPU frequency driver
pamc32_cpufreq: Low: 667 MHz, High: 867 Mhz, Boot: 667 MHz
then no more lines are printed. I waited about 5 minutes before powring
off the machine. Rebooting with old kernel works.
How may I collect more information?
Bye,
Giuseppe
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
revision : 3.2 (pvr 8001 0302)
platform : PowerMac
model : PowerBook3,5
machine : PowerBook3,5
motherboard : PowerBook3,5 MacRISC2 MacRISC Power Macintosh
Device Tree model: PowerBook3,5
** Network interface configuration:
*** /etc/network/interfaces:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp
** PCI devices:
0000:00:0b.0 Host bridge [0600]: Apple Inc. UniNorth 1.5 AGP [106b:002d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Capabilities: [80] AGP version 1.0
Status: RQ=8 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Kernel driver in use: agpgart-uninorth
0000:00:10.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc.
[AMD/ATI] RV250/M9 GL [Mobility FireGL 9000/Radeon 9000] [1002:4c66] (rev 01)
(prog-if 00 [VGA controller])
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RV250/M9 GL [Mobility
FireGL 9000/Radeon 9000] [1002:4c66]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at b8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 0400 [size=256]
Region 2: Memory at b0000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at b0020000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=8 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: radeon
Kernel modules: radeonfb, radeon
0001:10:0b.0 Host bridge [0600]: Apple Inc. UniNorth 1.5 PCI [106b:002e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
0001:10:17.0 Unassigned class [ff00]: Apple Inc. KeyLargo Mac I/O [106b:0022]
(rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
Kernel driver in use: macio
0001:10:18.0 USB controller [0c03]: Apple Inc. KeyLargo USB [106b:0019]
(prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (750ns min, 21500ns max)
Interrupt: pin A routed to IRQ 27
Region 0: Memory at a0002000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
0001:10:19.0 USB controller [0c03]: Apple Inc. KeyLargo USB [106b:0019]
(prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (750ns min, 21500ns max)
Interrupt: pin A routed to IRQ 28
Region 0: Memory at a0001000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
0001:10:1a.0 CardBus bridge [0607]: Texas Instruments PCI1410 PC card Cardbus
Controller [104c:ac50] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 58
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=10, secondary=11, subordinate=14, sec-latency=176
Memory window 0: 84000000-87ffffff (prefetchable)
Memory window 1: 88000000-8bffffff
I/O window 0: 00001000-000010ff
I/O window 1: 00001100-000011ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
0002:24:0b.0 Host bridge [0600]: Apple Inc. UniNorth 1.5 Internal PCI
[106b:002f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
0002:24:0e.0 FireWire (IEEE 1394) [0c00]: LSI Corporation FW322/323 [TrueFire]
1394a Controller [11c1:5811] (prog-if 10 [OHCI])
Subsystem: LSI Corporation FW322/323 [TrueFire] 1394a Controller
[11c1:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (3000ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci
Kernel modules: firewire_ohci
0002:24:0f.0 Ethernet controller [0200]: Apple Inc. UniNorth GMAC (Sun GEM)
[106b:0021] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR+ INTx-
Latency: 16 (16000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f5200000 (32-bit, non-prefetchable) [size=2M]
Expansion ROM at f5100000 [disabled] [size=1M]
Kernel driver in use: gem
Kernel modules: sungem
** USB devices:
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: bullseye/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: powerpc (ppc)
Kernel: Linux 3.16.0-6-powerpc
Locale: LANG=it_IT.UTF-8, LC_CTYPE=it_IT.UTF-8 (charmap=UTF-8),
LANGUAGE=it_IT.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-5.6.0-2-powerpc depends on:
ii initramfs-tools [linux-initramfs-tool] 0.137
ii kmod 27+20200310-2
ii linux-base 4.6
ii linux-bootwrapper-5.6.0-2 5.6.14-2
Versions of packages linux-image-5.6.0-2-powerpc recommends:
ii apparmor 2.13.4-3
ii firmware-linux-free 20200122-1
Versions of packages linux-image-5.6.0-2-powerpc suggests:
pn debian-kernel-handbook <none>
pn grub-ieee1275 <none>
pn linux-doc-5.6 <none>
pn mkvmlinuz <none>
Versions of packages linux-image-5.6.0-2-powerpc is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux-nonfree 0.43
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
