Package: src:linux
Version: 5.4.13-1
Severity: normal
Dear Maintainer,
after the latest upgrade, the upload speed with this 32-bit kernel became very
slow. Downgrading to kernel linux-image-4.19.0-6-686-pae solves the problem.
speed linux-image-5.4.0-3-686-pae 700-750 KB/s
speed linux-image-4.19.0-6-686-pae 90-95 MB/s
Packages r8168-dkms and firmware-realtek are not installed.
lsmod |grep r8169
r8169 73728 0
libphy 57344 2 r8169,realtek
lshw -class network
*-network
description: Ethernet interface
product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:04:00.0
logical name: eth0
version: 02
serial: 00:19:99:7e:c1:a1
size: 1Gbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list rom
ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd
autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 duplex=full
ip=131.211.154.187 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s
resources: irq:16 ioport:2000(size=256) memory:fc400000-fc400fff
memory:fc900000-fc90ffff memory:fc420000-fc43ffff
*-network
description: Ethernet interface
product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:05:00.0
logical name: eth1
version: 02
serial: 00:19:99:7e:de:b4
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list rom
ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd
autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 latency=0
link=no multicast=yes port=MII
resources: irq:17 ioport:3000(size=256) memory:fc500000-fc500fff
memory:fca00000-fca0ffff memory:fc520000-fc53ffff
-- Package-specific info:
** Version:
Linux version 5.4.0-3-686-pae (debian-kernel@lists.debian.org) (gcc version
9.2.1 20200110 (Debian 9.2.1-23)) #1 SMP Debian 5.4.13-1 (2020-01-19)
** Command line:
BOOT_IMAGE=/vmlinuz-5.4.0-3-686-pae
root=UUID=be578b7d-8d8d-4905-b653-290d1eafa4c3 ro
** Not tainted
** Kernel log:
Unable to read kernel log; any relevant messages should be attached
** Model information
** Loaded modules:
nfsv3
nfs_acl
nfs
lockd
grace
fscache
ipt_REJECT
nf_reject_ipv4
nft_compat
nft_counter
nf_tables
nfnetlink
rfkill
snd_hda_codec_hdmi
snd_hda_codec_realtek
snd_hda_codec_generic
ledtrig_audio
joydev
snd_hda_intel
snd_intel_nhlt
coretemp
snd_hda_codec
kvm
snd_hda_core
r8169
sg
realtek
snd_hwdep
libphy
tpm_infineon
snd_pcm_oss
tpm_tis
serio_raw
snd_mixer_oss
tpm_tis_core
snd_pcm
iTCO_wdt
irqbypass
ppdev
iTCO_vendor_support
fschmd
watchdog
snd_timer
pcspkr
tpm
snd
parport_pc
parport
rng_core
soundcore
evdev
acpi_cpufreq
sunrpc
loop
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
hid_cherry
sr_mod
sd_mod
cdrom
hid_generic
usbhid
hid
i915
ata_generic
ata_piix
libata
psmouse
scsi_mod
lpc_ich
mfd_core
i2c_i801
video
i2c_algo_bit
drm_kms_helper
ehci_pci
uhci_hcd
ehci_hcd
drm
usbcore
usb_common
button
** Network interface configuration:
*** /etc/network/interfaces:
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet static
address 131.211.154.187
netmask 255.255.254.0
network 131.211.154.0
broadcast 131.211.155.255
gateway 131.211.154.1
dns-nameservers 131.211.154.162 131.211.154.5 131.211.4.5
dns-search chem.uu.nl
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP
group default qlen 1000
link/ether 00:19:99:7e:c1:a1 brd ff:ff:ff:ff:ff:ff
inet 131.211.154.187/23 brd 131.211.155.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::219:99ff:fe7e:c1a1/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state
DOWN group default qlen 1000
link/ether 00:19:99:7e:de:b4 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
eth1: 0 0 0 0 0 0 0 0 0
0 32 0 0 0 0 0
lo: 479944 2146 0 0 0 0 0 0 479944
2146 0 0 0 0 0 0
eth0: 981092 10287 0 80 0 0 0 170 357451
1906 1 0 0 0 0 0
*** Protocol statistics:
Ip:
Forwarding: 2
2938 total packets received
0 forwarded
0 incoming packets discarded
2769 incoming packets delivered
1879 requests sent out
Icmp:
18 ICMP messages received
0 input ICMP message failed
ICMP input histogram:
echo requests: 18
21 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 3
echo replies: 18
IcmpMsg:
InType8: 18
OutType0: 18
OutType3: 3
Tcp:
15 active connection openings
6 passive connection openings
0 failed connection attempts
2 connection resets received
4 connections established
4038 segments received
3773 segments sent out
11 segments retransmitted
0 bad segments received
31 resets sent
Udp:
224 packets received
3 packets to unknown port received
0 packet receive errors
224 packets sent
0 receive buffer errors
0 send buffer errors
IgnoredMulti: 628
UdpLite:
TcpExt:
8 TCP sockets finished time wait in fast timer
29 delayed acks sent
2383 packet headers predicted
216 acknowledgments not containing data payload received
1966 predicted acknowledgments
TCPSackRecovery: 5
9 fast retransmits
TCPLossProbes: 2
TCPDSACKRecv: 5
4 connections reset due to unexpected data
1 connections reset due to early user close
TCPSackMerged: 2
TCPSackShiftFallback: 25
TCPRcvCoalesce: 131
TCPAutoCorking: 3
TCPOrigDataSent: 2500
TCPKeepAlive: 3
TCPDelivered: 2520
IpExt:
InBcastPkts: 628
InOctets: 498912
OutOctets: 329747
InBcastOctets: 85032
InNoECTPkts: 2961
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4 Series Chipset DRAM Controller
[8086:2e10] (rev 03)
Subsystem: Fujitsu Technology Solutions 4 Series Chipset DRAM
Controller [1734:114c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 4 Series Chipset PCI Express Root
Port [8086:2e11] (rev 03) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: [disabled]
Memory behind bridge: [disabled]
Prefetchable memory behind bridge: [disabled]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation 4 Series Chipset
Integrated Graphics Controller [8086:2e12] (rev 03) (prog-if 00 [VGA
controller])
Subsystem: Fujitsu Technology Solutions 4 Series Chipset Integrated
Graphics Controller [1734:114c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fc000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1c40 [size=8]
Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:1a.0 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB
UHCI Controller #4 [8086:3a67] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB
UHCI Controller [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1820 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB
UHCI Controller #5 [8086:3a68] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB
UHCI Controller [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB
UHCI Controller #6 [8086:3a69] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB
UHCI Controller [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 1860 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB2
EHCI Controller #2 [8086:3a6c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB2
EHCI Controller [1734:114d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: Memory at fc804000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device [0403]: Intel Corporation 82801JD/DO (ICH10 Family) HD
Audio Controller [8086:3a6e] (rev 02)
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) HD
Audio Controller [1734:1157]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 33
Region 0: Memory at fc800000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI
Express Port 1 [8086:3a70] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00004000-00004fff [size=4K]
Memory behind bridge: f0000000-f01fffff [size=2M]
Prefetchable memory behind bridge: 00000000f0200000-00000000f03fffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI
Express Port 2 [8086:3a72] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 30
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00005000-00005fff [size=4K]
Memory behind bridge: f0400000-f05fffff [size=2M]
Prefetchable memory behind bridge: 00000000f0600000-00000000f07fffff
[size=2M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI
Express Port 5 [8086:3a78] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 31
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff [size=4K]
Memory behind bridge: fc400000-fc4fffff [size=1M]
Prefetchable memory behind bridge: 00000000fc900000-00000000fc9fffff
[size=1M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI
Express Port 6 [8086:3a7a] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 32
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00003000-00003fff [size=4K]
Memory behind bridge: fc500000-fc5fffff [size=1M]
Prefetchable memory behind bridge: 00000000fca00000-00000000fcafffff
[size=1M]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB
UHCI Controller #1 [8086:3a64] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB
UHCI Controller [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB
UHCI Controller #2 [8086:3a65] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB
UHCI Controller [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 18a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB
UHCI Controller #3 [8086:3a66] (rev 02) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB
UHCI Controller [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 18c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB2
EHCI Controller #1 [8086:3a6a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) USB2
EHCI Controller [1734:114d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fc805000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
I/O behind bridge: [disabled]
Memory behind bridge: [disabled]
Prefetchable memory behind bridge: [disabled]
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- VGA16- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JDO (ICH10DO) LPC Interface
Controller [8086:3a14] (rev 02)
Subsystem: Fujitsu Technology Solutions 82801JDO (ICH10DO) LPC
Interface Controller [1734:114d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 IDE interface [0101]: Intel Corporation 82801JD/DO (ICH10 Family)
4-port SATA IDE Controller [8086:3a00] (rev 02) (prog-if 8f [PCI native mode
controller, supports both channels switched to ISA compatibility mode, supports
bus mastering])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family)
4-port SATA IDE Controller [1734:114d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 1c58 [size=8]
Region 1: I/O ports at 1c4c [size=4]
Region 2: I/O ports at 1c50 [size=8]
Region 3: I/O ports at 1c48 [size=4]
Region 4: I/O ports at 1c10 [size=16]
Region 5: I/O ports at 1c00 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix, ata_generic
00:1f.3 SMBus [0c05]: Intel Corporation 82801JD/DO (ICH10 Family) SMBus
Controller [8086:3a60] (rev 02)
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family) SMBus
Controller [1734:114d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fc806000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1100 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
00:1f.5 IDE interface [0101]: Intel Corporation 82801JD/DO (ICH10 Family)
2-port SATA IDE Controller [8086:3a06] (rev 02) (prog-if 85 [PCI native
mode-only controller, supports bus mastering])
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family)
2-port SATA IDE Controller [1734:114d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: I/O ports at 1c70 [size=8]
Region 1: I/O ports at 1c64 [size=4]
Region 2: I/O ports at 1c68 [size=8]
Region 3: I/O ports at 1c60 [size=4]
Region 4: I/O ports at 1c30 [size=16]
Region 5: I/O ports at 1c20 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix, ata_generic
00:1f.6 Signal processing controller [1180]: Intel Corporation 82801JD/DO
(ICH10 Family) Thermal Subsystem [8086:3a62] (rev 02)
Subsystem: Fujitsu Technology Solutions 82801JD/DO (ICH10 Family)
Thermal Subsystem [1734:114d]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fc807000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 02)
Subsystem: Fujitsu Technology Solutions RTL8111/8168/8411 PCI Express
Gigabit Ethernet Controller [1734:1159]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 2000 [size=256]
Region 2: Memory at fc400000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fc900000 (64-bit, prefetchable) [size=64K]
Expansion ROM at fc420000 [virtual] [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 02)
Subsystem: Fujitsu Technology Solutions RTL8111/8168/8411 PCI Express
Gigabit Ethernet Controller [1734:1159]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at fc500000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fca00000 (64-bit, prefetchable) [size=64K]
Expansion ROM at fc520000 [virtual] [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
** USB devices:
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 003: ID 046a:0023 Cherry GmbH Keyboard
Bus 006 Device 002: ID 046d:c05b Logitech, Inc. M-U0004 810-001317 [B110
Optical USB Mouse]
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: bullseye/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 5.4.0-3-686-pae (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8),
LANGUAGE=en_US:en (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-5.4.0-3-686-pae depends on:
ii initramfs-tools [linux-initramfs-tool] 0.136
ii kmod 26+20191223-1
ii linux-base 4.6
Versions of packages linux-image-5.4.0-3-686-pae recommends:
ii apparmor 2.13.3-7
ii firmware-linux-free 3.4
Versions of packages linux-image-5.4.0-3-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.04-5
pn linux-doc-5.4 <none>
Versions of packages linux-image-5.4.0-3-686-pae is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
