Package: src:linux
Version: 4.1.6-1
Severity: normal
Dear Maintainer,
Sometimes my UPS (Advice) starts beeping every 20 seconds or so (electricity is
not turned off and the computer continues to work).
To stop beeping I reboot.
Motherboard: Gigabyte H67A-UD3H
Here is the last part of dmesg output:
[80956.127530] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[81253.729422] usb 3-1.6: USB disconnect, device number 8
[81254.017093] usb 3-1.6: new low-speed USB device number 9 using ehci-pci
[81254.115853] usb 3-1.6: New USB device found, idVendor=1c4f, idProduct=0016
[81254.115858] usb 3-1.6: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[81254.115860] usb 3-1.6: Product: USB Keyboard
[81254.115863] usb 3-1.6: Manufacturer: SIGMACHIP
[81254.119278] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.0/0003:1C4F:0016.0009/input/input24
[81254.173723] hid-generic 0003:1C4F:0016.0009: input,hidraw0: USB HID v1.10
Keyboard [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input0
[81264.187547] hid-generic 0003:1C4F:0016.000A: usb_submit_urb(ctrl) failed: -1
[81264.187575] hid-generic 0003:1C4F:0016.000A: timeout initializing reports
[81264.187882] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.1/0003:1C4F:0016.000A/input/input25
[81264.243689] hid-generic 0003:1C4F:0016.000A: input,hidraw2: USB HID v1.10
Device [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input1
[81392.081168] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[81541.396630] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[82745.525980] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[82798.635872] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[83497.118588] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[83652.450465] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[83968.129094] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[86329.325986] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[87405.188725] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[87676.430232] usb 3-1-port6: disabled by hub (EMI?), re-enabling...
[87676.430241] usb 3-1.6: USB disconnect, device number 9
[87676.721746] usb 3-1.6: new low-speed USB device number 10 using ehci-pci
[87676.820299] usb 3-1.6: New USB device found, idVendor=1c4f, idProduct=0016
[87676.820303] usb 3-1.6: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[87676.820306] usb 3-1.6: Product: USB Keyboard
[87676.820308] usb 3-1.6: Manufacturer: SIGMACHIP
[87676.823925] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.0/0003:1C4F:0016.000B/input/input26
[87676.878292] hid-generic 0003:1C4F:0016.000B: input,hidraw0: USB HID v1.10
Keyboard [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input0
[87686.892065] hid-generic 0003:1C4F:0016.000C: usb_submit_urb(ctrl) failed: -1
[87686.892072] hid-generic 0003:1C4F:0016.000C: timeout initializing reports
[87686.892171] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.1/0003:1C4F:0016.000C/input/input27
[87686.948039] hid-generic 0003:1C4F:0016.000C: input,hidraw2: USB HID v1.10
Device [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input1
-- Package-specific info:
** Version:
Linux version 4.1.0-2-686-pae (debian-kernel@lists.debian.org) (gcc version
4.9.3 (Debian 4.9.3-3) ) #1 SMP Debian 4.1.6-1 (2015-08-23)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.1.0-2-686-pae
root=UUID=54902130-d49b-4173-bb4f-5eacb0595474 ro selinux=1 security=selinux
quiet
** Not tainted
** Kernel log:
[54645.278337] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[56091.403730] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[59230.781944] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[59409.777609] perf interrupt took too long (2508 > 2500), lowering
kernel.perf_event_max_sample_rate to 50000
[59594.555331] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[59647.665273] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[60290.654916] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[61341.896171] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[61413.046912] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[63665.797488] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[65027.453488] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[65629.750036] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[65736.971042] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[66422.539491] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[66938.640360] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[67081.951387] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[67587.192184] usb 3-1-port6: disabled by hub (EMI?), re-enabling...
[67587.192193] usb 3-1.6: USB disconnect, device number 6
[67587.497466] usb 3-1.6: new low-speed USB device number 7 using ehci-pci
[67587.595870] usb 3-1.6: New USB device found, idVendor=1c4f, idProduct=0016
[67587.595875] usb 3-1.6: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[67587.595878] usb 3-1.6: Product: USB Keyboard
[67587.595880] usb 3-1.6: Manufacturer: SIGMACHIP
[67587.599509] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.0/0003:1C4F:0016.0005/input/input20
[67587.654034] hid-generic 0003:1C4F:0016.0005: input,hidraw0: USB HID v1.10
Keyboard [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input0
[67597.667837] hid-generic 0003:1C4F:0016.0006: usb_submit_urb(ctrl) failed: -1
[67597.667853] hid-generic 0003:1C4F:0016.0006: timeout initializing reports
[67597.668040] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.1/0003:1C4F:0016.0006/input/input21
[67597.724025] hid-generic 0003:1C4F:0016.0006: input,hidraw2: USB HID v1.10
Device [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input1
[67940.287915] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[68530.367569] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[68553.411638] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[68752.840720] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[68874.105102] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[69476.417693] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[71490.079320] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[72196.616998] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[73288.522012] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[73628.253946] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[73811.644725] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[74103.261774] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[74744.248329] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[76684.900640] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[76778.093995] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[76915.384905] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[78319.387693] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[78362.475588] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[78846.496094] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[79400.690143] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[79603.844507] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[80600.512569] usb 3-1-port6: disabled by hub (EMI?), re-enabling...
[80600.512578] usb 3-1.6: USB disconnect, device number 7
[80600.797419] usb 3-1.6: new low-speed USB device number 8 using ehci-pci
[80600.896503] usb 3-1.6: New USB device found, idVendor=1c4f, idProduct=0016
[80600.896508] usb 3-1.6: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[80600.896510] usb 3-1.6: Product: USB Keyboard
[80600.896513] usb 3-1.6: Manufacturer: SIGMACHIP
[80600.900268] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.0/0003:1C4F:0016.0007/input/input22
[80600.954320] hid-generic 0003:1C4F:0016.0007: input,hidraw0: USB HID v1.10
Keyboard [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input0
[80610.967774] hid-generic 0003:1C4F:0016.0008: usb_submit_urb(ctrl) failed: -1
[80610.967796] hid-generic 0003:1C4F:0016.0008: timeout initializing reports
[80610.968015] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.1/0003:1C4F:0016.0008/input/input23
[80611.023992] hid-generic 0003:1C4F:0016.0008: input,hidraw2: USB HID v1.10
Device [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input1
[80692.952254] Process accounting resumed
[80956.127530] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[81253.729422] usb 3-1.6: USB disconnect, device number 8
[81254.017093] usb 3-1.6: new low-speed USB device number 9 using ehci-pci
[81254.115853] usb 3-1.6: New USB device found, idVendor=1c4f, idProduct=0016
[81254.115858] usb 3-1.6: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[81254.115860] usb 3-1.6: Product: USB Keyboard
[81254.115863] usb 3-1.6: Manufacturer: SIGMACHIP
[81254.119278] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.0/0003:1C4F:0016.0009/input/input24
[81254.173723] hid-generic 0003:1C4F:0016.0009: input,hidraw0: USB HID v1.10
Keyboard [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input0
[81264.187547] hid-generic 0003:1C4F:0016.000A: usb_submit_urb(ctrl) failed: -1
[81264.187575] hid-generic 0003:1C4F:0016.000A: timeout initializing reports
[81264.187882] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.1/0003:1C4F:0016.000A/input/input25
[81264.243689] hid-generic 0003:1C4F:0016.000A: input,hidraw2: USB HID v1.10
Device [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input1
[81392.081168] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[81541.396630] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[82745.525980] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[82798.635872] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[83497.118588] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[83652.450465] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[83968.129094] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[86329.325986] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[87405.188725] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
[87676.430232] usb 3-1-port6: disabled by hub (EMI?), re-enabling...
[87676.430241] usb 3-1.6: USB disconnect, device number 9
[87676.721746] usb 3-1.6: new low-speed USB device number 10 using ehci-pci
[87676.820299] usb 3-1.6: New USB device found, idVendor=1c4f, idProduct=0016
[87676.820303] usb 3-1.6: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[87676.820306] usb 3-1.6: Product: USB Keyboard
[87676.820308] usb 3-1.6: Manufacturer: SIGMACHIP
[87676.823925] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.0/0003:1C4F:0016.000B/input/input26
[87676.878292] hid-generic 0003:1C4F:0016.000B: input,hidraw0: USB HID v1.10
Keyboard [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input0
[87686.892065] hid-generic 0003:1C4F:0016.000C: usb_submit_urb(ctrl) failed: -1
[87686.892072] hid-generic 0003:1C4F:0016.000C: timeout initializing reports
[87686.892171] input: SIGMACHIP USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.6/3-1.6:1.1/0003:1C4F:0016.000C/input/input27
[87686.948039] hid-generic 0003:1C4F:0016.000C: input,hidraw2: USB HID v1.10
Device [SIGMACHIP USB Keyboard] on usb-0000:00:1a.0-1.6/input1
[87778.972093] usb 3-1.3: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33
rq 9 len 8 ret -110
** Model information
not available
** Loaded modules:
usblp
fuse
cpufreq_powersave
cpufreq_stats
cpufreq_conservative
cpufreq_userspace
snd_hda_codec_hdmi
binfmt_misc
snd_hda_codec_realtek
snd_hda_codec_generic
x86_pkg_temp_thermal
intel_powerclamp
intel_rapl
iosf_mbi
kvm_intel
kvm
iTCO_wdt
iTCO_vendor_support
crc32_pclmul
nouveau
joydev
gspca_t613
gspca_main
videodev
media
aesni_intel
mxm_wmi
snd_hda_intel
wmi
snd_hda_controller
aes_i586
video
snd_hda_codec
evdev
ttm
snd_hda_core
xts
drm_kms_helper
snd_hwdep
lrw
snd_pcm_oss
gf128mul
drm
snd_mixer_oss
ablk_helper
snd_pcm
snd_timer
serio_raw
cryptd
pcspkr
i2c_algo_bit
snd
i2c_i801
sg
soundcore
mei_me
lpc_ich
shpchp
mei
mfd_core
8250_fintek
processor
button
thermal_sys
coretemp
loop
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
sd_mod
hid_generic
usbhid
hid
xhci_pci
ehci_pci
crc32c_intel
xhci_hcd
ahci
ehci_hcd
libahci
firewire_ohci
firewire_core
libata
crc_itu_t
r8169
mii
scsi_mod
usbcore
usb_common
floppy
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor
Family DRAM Controller [8086:0100] (rev 09)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: snb_uncore
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core
Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 24
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f9000000-faffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series
Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: Gigabyte Technology Co., Ltd 6 Series/C200 Series Chipset
Family MEI Controller [1458:1c3a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 35
Region 0: Memory at fbfff000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Gigabyte Technology Co., Ltd 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset
Family High Definition Audio Controller [8086:1c20] (rev 04)
Subsystem: Gigabyte Technology Co., Ltd 6 Series/C200 Series Chipset
Family High Definition Audio Controller [1458:a102]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 36
Region 0: Memory at fbff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 1 [8086:1c10] (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: cf800000-cf9fffff
Prefetchable memory behind bridge: 00000000cfa00000-00000000cfbfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 6 [8086:1c1a] (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Prefetchable memory behind bridge: 00000000fbe00000-00000000fbefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.6 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
b4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Bus: primary=00, secondary=04, subordinate=05, sec-latency=0
Memory behind bridge: fbd00000-fbdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 8 [8086:1c1e] (rev b4) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin D routed to IRQ 19
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Memory behind bridge: fbc00000-fbcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Gigabyte Technology Co., Ltd 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge [0601]: Intel Corporation H67 Express Chipset Family LPC
Controller [8086:1c4a] (rev 04)
Subsystem: Gigabyte Technology Co., Ltd H67 Express Chipset Family LPC
Controller [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset
Family SATA AHCI Controller [8086:1c02] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Gigabyte Technology Co., Ltd 6 Series/C200 Series Chipset
Family SATA AHCI Controller [1458:b005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 26
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=32]
Region 5: Memory at fbffc000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family
SMBus Controller [8086:1c22] (rev 04)
Subsystem: Gigabyte Technology Co., Ltd 6 Series/C200 Series Chipset
Family SMBus Controller [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffb000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GT218 [GeForce
8400 GS Rev. 3] [10de:10c3] (rev a2) (prog-if 00 [VGA controller])
Subsystem: NVIDIA Corporation GT218 [GeForce 8400 GS Rev. 3] [10de:066d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 37
Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at ee000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at ef00 [size=128]
[virtual] Expansion ROM at fa000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nouveau
Kernel modules: nouveau
01:00.1 Audio device [0403]: NVIDIA Corporation High Definition Audio
Controller [10de:0be3] (rev a1)
Subsystem: NVIDIA Corporation G98 [GeForce 8400GS] [10de:066d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at faffc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 25
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fbeff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fbef8000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
04:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device
[1283:8892] (rev 10) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Bus: primary=04, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: fbd00000-fbdfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
05:03.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbdff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fbdf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire_ohci
06:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host
Controller [1033:0194] (rev 03) (prog-if 30 [XHCI])
Subsystem: Gigabyte Technology Co., Ltd uPD720200 USB 3.0 Host
Controller [1458:5007]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fbcfe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
** USB devices:
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 010: ID 1c4f:0016 SiGma Micro
Bus 003 Device 005: ID 192f:0416 Avago Technologies, Pte. ADNS-5700 Optical
Mouse Controller (3-button)
Bus 003 Device 004: ID 17a1:0128
Bus 003 Device 003: ID 0665:5161 Cypress Semiconductor USB to Serial
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: stretch/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'stable-updates'), (500, 'unstable'),
(500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 4.1.0-2-686-pae (SMP w/8 CPU cores)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.1.0-2-686-pae depends on:
ii debconf [debconf-2.0] 1.5.59
ii initramfs-tools [linux-initramfs-tool] 0.123
ii kmod 22-1.1
ii linux-base 4.0
Versions of packages linux-image-4.1.0-2-686-pae recommends:
ii firmware-linux-free 3.4
ii irqbalance 1.1.0-2
ii libc6-i686 2.22-5
Versions of packages linux-image-4.1.0-2-686-pae suggests:
pn debian-kernel-handbook <none>
ii extlinux 3:6.03+dfsg-11
ii grub-pc 2.02~beta2-36
pn linux-doc-4.1 <none>
Versions of packages linux-image-4.1.0-2-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
ii firmware-ivtv 20160110-1
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 20160110-1
ii firmware-misc-nonfree [firmware-ralink] 20160110-1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
ii firmware-realtek 20160110-1
pn xen-hypervisor <none>
-- debconf information excluded
