So I rebuilt initrd.img, after adding megaraid2 to /etc/mkinitrd/modules, and then everything shows up.
Attaching dmesg from bootup.
Linux version 2.4.27-1-686-smp ([EMAIL PROTECTED]) (gcc version 3.3.4 (Debian
1:3.3.4-9)) #1 SMP Fri Sep 3 06:34:36 UTC 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
BIOS-e820: 000000003ffc0000 - 000000003ffcfc00 (ACPI data)
BIOS-e820: 000000003ffcfc00 - 000000003ffff000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000fec90000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
hm, page 000fe000 reserved twice.
hm, page 000ff000 reserved twice.
hm, page 000f0000 reserved twice.
On node 0 totalpages: 262080
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32704 pages.
ACPI: RSDP (v000 DELL ) @ 0x000fd6c0
ACPI: RSDT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd6d4
ACPI: FADT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd708
ACPI: MADT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd77c
ACPI: SPCR (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd824
ACPI: HPET (v001 DELL PE BKC 0x00000001 MSFT 0x0100000a) @ 0x000fd874
ACPI: DSDT (v001 DELL PE BKC 0x00000001 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Unknown CPU [15:4] APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
Processor #6 Unknown CPU [15:4] APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1 Unknown CPU [15:4] APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled)
Processor #7 Unknown CPU [15:4] APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: DELL Product ID: PE 016D APIC at: 0xFEE00000
I/O APIC #8 Version 32 at 0xFEC00000.
I/O APIC #9 Version 32 at 0xFEC80000.
I/O APIC #10 Version 32 at 0xFEC83000.
I/O APIC #11 Version 32 at 0xFEC84000.
Enabling APIC mode: Flat. Using 4 I/O APICs
Processors: 4
Kernel command line: root=/dev/sda1 ro
Initializing CPU#0
Detected 2793.124 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5570.56 BogoMIPS
Memory: 1029292k/1048320k available (1296k kernel code, 18644k reserved, 474k
data, 124k init, 130816k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 01
per-CPU timeslice cutoff: 2925.13 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5583.66 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 01
Booting processor 2/6 eip 3000
Initializing CPU#2
masked ExtINT on CPU#2
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5583.66 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 3
Intel machine check reporting enabled on CPU#2.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
CPU2: Intel(R) Xeon(TM) CPU 2.80GHz stepping 01
Booting processor 3/7 eip 3000
Initializing CPU#3
masked ExtINT on CPU#3
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5583.66 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 3
Intel machine check reporting enabled on CPU#3.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
CPU3: Intel(R) Xeon(TM) CPU 2.80GHz stepping 01
Total of 4 processors activated (22321.56 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
cpu_sibling_map[2] = 3
cpu_sibling_map[3] = 2
ENABLING IO-APIC IRQs
Setting 8 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 8 ... ok.
Setting 9 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 9 ... ok.
Setting 10 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 10 ... ok.
Setting 11 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 11 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 8-0, 8-3, 8-5, 8-7, 8-10, 8-11, 8-13, 8-17, 8-22, 9-0,
9-3, 9-4, 9-5, 9-6, 9-7, 9-8, 9-9, 9-10, 9-11, 9-12, 9-13, 9-15, 9-16, 9-17,
9-18, 9-19, 9-20, 9-21, 9-22, 9-23, 10-2, 10-3, 10-4, 10-5, 10-6, 10-7, 10-8,
10-9, 10-10, 10-11, 10-12, 10-13, 10-14, 10-15, 10-16, 10-17, 10-18, 10-19,
10-20, 10-21, 10-22, 10-23, 11-12, 11-13, 11-14, 11-15, 11-16, 11-17, 11-18,
11-19, 11-20, 11-21, 11-22, 11-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 45.
number of IO-APIC #8 registers: 24.
number of IO-APIC #9 registers: 24.
number of IO-APIC #10 registers: 24.
number of IO-APIC #11 registers: 24.
testing the IO APIC.......................
IO APIC #8......
.... register #00: 08000000
....... : physical APIC id: 08
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 00F 0F 0 0 0 0 0 1 1 39
02 00F 0F 0 0 0 0 0 1 1 31
03 000 00 1 0 0 0 0 0 0 00
04 00F 0F 0 0 0 0 0 1 1 41
05 000 00 1 0 0 0 0 0 0 00
06 00F 0F 0 0 0 0 0 1 1 49
07 000 00 1 0 0 0 0 0 0 00
08 00F 0F 0 0 0 0 0 1 1 51
09 00F 0F 0 0 0 0 0 1 1 59
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 00F 0F 0 0 0 0 0 1 1 61
0d 000 00 1 0 0 0 0 0 0 00
0e 00F 0F 0 0 0 0 0 1 1 69
0f 00F 0F 0 0 0 0 0 1 1 71
10 00F 0F 1 1 0 1 0 1 1 79
11 000 00 1 0 0 0 0 0 0 00
12 00F 0F 1 1 0 1 0 1 1 81
13 00F 0F 1 1 0 1 0 1 1 89
14 00F 0F 1 1 0 1 0 1 1 91
15 00F 0F 1 1 0 1 0 1 1 99
16 000 00 1 0 0 0 0 0 0 00
17 00F 0F 1 1 0 1 0 1 1 A1
IO APIC #9......
.... register #00: 09000000
....... : physical APIC id: 09
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 09000000
....... : arbitration: 09
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 00F 0F 1 1 0 1 0 1 1 A9
02 00F 0F 1 1 0 1 0 1 1 B1
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 00F 0F 1 1 0 1 0 1 1 B9
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #10......
.... register #00: 0A000000
....... : physical APIC id: 0A
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 0A000000
....... : arbitration: 0A
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 00F 0F 1 1 0 1 0 1 1 C1
01 00F 0F 1 1 0 1 0 1 1 C9
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #11......
.... register #00: 0B000000
....... : physical APIC id: 0B
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 0B000000
....... : arbitration: 0B
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 00F 0F 1 1 0 1 0 1 1 D1
01 00F 0F 1 1 0 1 0 1 1 D9
02 00F 0F 1 1 0 1 0 1 1 E1
03 00F 0F 1 1 0 1 0 1 1 E9
04 00F 0F 1 1 0 1 0 1 1 32
05 00F 0F 1 1 0 1 0 1 1 3A
06 00F 0F 1 1 0 1 0 1 1 42
07 00F 0F 1 1 0 1 0 1 1 4A
08 00F 0F 1 1 0 1 0 1 1 52
09 00F 0F 1 1 0 1 0 1 1 5A
0a 00F 0F 1 1 0 1 0 1 1 62
0b 00F 0F 1 1 0 1 0 1 1 6A
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ23 -> 0:23
IRQ25 -> 1:1
IRQ26 -> 1:2
IRQ38 -> 1:14
IRQ48 -> 2:0
IRQ49 -> 2:1
IRQ72 -> 3:0
IRQ73 -> 3:1
IRQ74 -> 3:2
IRQ75 -> 3:3
IRQ76 -> 3:4
IRQ77 -> 3:5
IRQ78 -> 3:6
IRQ79 -> 3:7
IRQ80 -> 3:8
IRQ81 -> 3:9
IRQ82 -> 3:10
IRQ83 -> 3:11
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2793.0391 MHz.
..... host bus clock speed is 199.5027 MHz.
cpu: 0, clocks: 1995027, slice: 399005
CPU0<T0:1995024,T1:1596016,D:3,S:399005,C:1995027>
cpu: 1, clocks: 1995027, slice: 399005
cpu: 2, clocks: 1995027, slice: 399005
cpu: 3, clocks: 1995027, slice: 399005
CPU1<T0:1995024,T1:1197008,D:6,S:399005,C:1995027>
CPU2<T0:1995024,T1:798000,D:9,S:399005,C:1995027>
CPU3<T0:1995024,T1:398992,D:12,S:399005,C:1995027>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0xe)
All processors have done init_idle
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfbf7e, last bus=11
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX/ICH [8086/24d0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 16
PCI->APIC IRQ transform: (B0,I4,P0) -> 16
PCI->APIC IRQ transform: (B0,I5,P0) -> 16
PCI->APIC IRQ transform: (B0,I6,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B2,I5,P0) -> 26
PCI->APIC IRQ transform: (B2,I5,P1) -> 25
PCI->APIC IRQ transform: (B6,I7,P0) -> 48
PCI->APIC IRQ transform: (B7,I8,P0) -> 49
PCI->APIC IRQ transform: (B9,I4,P0) -> 82
PCI->APIC IRQ transform: (B11,I13,P0) -> 18
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <[EMAIL PROTECTED]>
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3900 blocks [1 disk] into ram disk...
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done.
Freeing initrd memory: 3900k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 124k freed
SCSI subsystem driver Revision: 1.00
megaraid: v2.10.3 (Release Date: Thu Apr 8 16:16:05 EDT 2004)
megaraid: found 0x1000:0x1960:bus 9:slot 4:func 0
scsi0:Found MegaRAID controller at 0xf8832000, IRQ:82
megaraid: [350O:1.09] detected 1 logical drives.
megaraid: supports extended CDBs.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
scsi0 : LSI Logic MegaRAID 350O 254 commands 16 targs 5 chans 7 luns
blk: queue c1c3a418, I/O limit 4095Mb (mask 0xffffffff)
scsi0: scanning scsi channel 0 for logical drives.
Vendor: MegaRAID Model: LD0 RAID1 39900R Rev: 350O
Type: Direct-Access ANSI SCSI revision: 02
blk: queue c1c3a218, I/O limit 4095Mb (mask 0xffffffff)
scsi0: scanning scsi channel 1 for logical drives.
scsi0: scanning scsi channel 2 for logical drives.
scsi0: scanning scsi channel 4 [P0] for physical devices.
Vendor: PE/PV Model: 1x6 SCSI BP Rev: 1.0
Type: Processor ANSI SCSI revision: 02
blk: queue f7efde18, I/O limit 4095Mb (mask 0xffffffff)
scsi0: scanning scsi channel 5 [P1] for physical devices.
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
megaraid: v1.18k (Release Date: Thu Aug 28 10:05:11 EDT 2003)
megaraid: found 0x1000:0x1960:idx 0:bus 9:slot 4:func 0
megaraid: mem region busy!
megaraid: no BIOS enabled.
Fusion MPT base driver 2.05.16
Copyright (c) 1999-2004 LSI Logic Corporation
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator,Target}
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator,Target}
mptbase: 2 MPT adapters found, 2 installed.
Fusion MPT SCSI Host driver 2.05.16
scsi1 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=26
scsi2 : ioc1: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=255, IRQ=25
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
scsi3 : SCSI host adapter emulation for IDE ATAPI devices
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 286515200 512-byte hdwr sectors (146696 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
hda: SAMSUNG CD-ROM SN-124, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-cdrom driver.
hda: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
LVM version 1.0.8(17/11/2003) module loaded
loop: loaded (max 8 devices)
inserting floppy driver for 2.4.27-1-686-smp
FDC 0 is a National Semiconductor PC87306
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,0), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,4), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 1835000k swap-space (priority -1)
lp: driver loaded but no devices found
Intel(R) PRO/1000 Network Driver - version 5.2.52-k3
Copyright (c) 1999-2004 Intel Corporation.
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 06:36:50 Sep 3 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xace0, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xacc0, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xaca0, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: Intel Corp. 82801EB USB2
ehci_hcd 00:1d.7: irq 23, pci mem f8a40000
usb.c: new USB bus registered, assigned bus number 4
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 6 ports detected
hub.c: connect-debounce failed, port 1 disabled
hub.c: new USB device 00:1d.7-3, assigned address 2
hub.c: USB hub found
hub.c: 2 ports detected
Real Time Clock Driver v1.10f
hub.c: new USB device 00:1d.2-2, assigned address 2
usb.c: USB device 2 (vend/prod 0x51d/0x2) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
usb-uhci.c: interrupt, status 3, frame# 473
e1000: eth1: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
hiddev0: USB HID v1.10 Device [American Power Conversion Smart-UPS 1500 RM
FW:617.3.I USB FW:1.5] on usb3:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
