Package: kernel-image-2.6.8-1-k7-smp
Version: 2.6.8-3
Severity: normal
-- System Information:
Debian Release: 3.1
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.8-1-k7-smp
Locale: LANG=C, LC_CTYPE=C (ignored: LC_ALL set to C)
Versions of packages kernel-image-2.6.8-1-k7-smp depends on:
ii coreutils [fileutils] 5.2.1-2 The GNU core utilities
ii fileutils 5.2.1-2 The GNU file management utilities
ii initrd-tools 0.1.74 tools to create initrd image for p
ii module-init-tools 3.1-pre5-7 tools for managing Linux kernel mo
-- no debconf information
Interesting part of boot log:
<snip>
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f4a00
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x576a, dseg 0xf0000
PNPBIOS fault.. attempting recovery.
PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to continue
PnPBIOS: You may need to reboot with the "nobiospnp" option to operate stably
PnPBIOS: Check with your vendor for an updated BIOS
PnPBIOS: get_dev_node: unexpected status 0x28
PnPBIOS: 6 nodes reported by PnP BIOS; 6 recorded by driver
PCI: Using ACPI for IRQ routing
<snip>
This sounds bad, but seems to make no difference??
Tyan says it is not a problem with RedHat or SuSe running the same kernel
version (and fails to show up in their dmesg).
loop... 3145.72 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Opteron(tm) Processor 242 stepping 0a
per-CPU timeslice cutoff: 2926.30 usecs.
task migration cache decay timeout: 3 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 3178.49 BogoMIPS
CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Opteron(tm) Processor 242 stepping 0a
Total of 2 processors activated (6324.22 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not
connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1592.0277 MHz.
..... host bus clock speed is 199.0034 MHz.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0: online
domain 0: span 01
groups: 01
domain 1: span 03
groups: 01 02
CPU1: online
domain 0: span 02
groups: 02
domain 1: span 03
groups: 02 01
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4612k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f4a00
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x576a, dseg 0xf0000
PNPBIOS fault.. attempting recovery.
PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to continue
PnPBIOS: You may need to reboot with the "nobiospnp" option to operate stably
PnPBIOS: Check with your vendor for an updated BIOS
PnPBIOS: get_dev_node: unexpected status 0x28
PnPBIOS: 6 nodes reported by PnP BIOS; 6 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:07.2[D] -> GSI 19 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:01:00.0[D] -> GSI 19 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:01:00.1[D] -> GSI 19 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:01:03.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 19 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 16 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 17 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 17 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:01:0b.1[B] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:01:0b.2[C] -> GSI 19 (level, low) -> IRQ 169
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 02000000
....... : arbitration: 02
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 0 1 0 1 0 1 1 71
0a 003 03 0 0 0 0 0 1 1 79
0b 003 03 0 0 0 0 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 0 0 0 0 0 1 1 A1
10 003 03 1 1 0 1 0 1 1 B1
11 003 03 1 1 0 1 0 1 1 C1
12 003 03 1 1 0 1 0 1 1 B9
13 003 03 1 1 0 1 0 1 1 A9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ177 -> 0:16
IRQ193 -> 0:17
IRQ185 -> 0:18
IRQ169 -> 0:19
.................................... done.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:01:0b.0, from 5 to 1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_acpi_add: no address or irqs in _CRS
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4612 blocks [1 disk] into ram disk...
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 168k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
sata_sil version 0.54
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 19 (level, low) -> IRQ 169
ata1: SATA max UDMA/100 cmd 0xF8821C80 ctl 0xF8821C8A bmdma 0xF8821C00 irq 169
ata2: SATA max UDMA/100 cmd 0xF8821CC0 ctl 0xF8821CCA bmdma 0xF8821C08 irq 169
ata3: SATA max UDMA/100 cmd 0xF8821E80 ctl 0xF8821E8A bmdma 0xF8821E00 irq 169
ata4: SATA max UDMA/100 cmd 0xF8821EC0 ctl 0xF8821ECA bmdma 0xF8821E08 irq 169
ata1: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e8 86:3c02 87:4023 88:203f
ata1: dev 0 ATA, max UDMA/100, 321672960 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e8 86:3c02 87:4023 88:203f
ata2: dev 0 ATA, max UDMA/100, 321672960 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
ata3: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata3: dev 0 ATA, max UDMA/133, 234441648 sectors: lba48
ata3: dev 0 configured for UDMA/100
scsi2 : sata_sil
ata4: no device found (phy stat 00000000)
scsi3 : sata_sil
Using anticipatory io scheduler
Vendor: ATA Model: HDS722516VLSA80 Rev: V34O
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: HDS722516VLSA80 Rev: V34O
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3120026AS Rev: 3.05
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: unknown partition table
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
SCSI device sdc: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sdc: drive cache: write back
/dev/scsi/host2/bus0/target0/lun0: p1 p2 p3
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
VFS: Can't find ext3 filesystem on dev sda6.
VFS: Can't find ext2 filesystem on dev sda6.
Adding 979920k swap on /dev/sda5. Priority:-1 extents:1
Real Time Clock Driver v1.12
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: PLEXTOR DVDR PX-712A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <[EMAIL PROTECTED]>
Capability LSM initialized
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
ohci1394: $Rev: 1223 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 17 (level, low) -> IRQ 193
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[193] MMIO=[fc9ff000-fc9ff7ff]
Max Packet=[2048]
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:01:03.0[A] -> GSI 18 (level, low) -> IRQ 185
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:01:0b.2[C] -> GSI 19 (level, low) -> IRQ 169
ehci_hcd 0000:01:0b.2: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:01:0b.2: irq 169, pci mem f8926800
ehci_hcd 0000:01:0b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:01:0b.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0810000303896]
ip1394: $Rev: 1224 $ Ben Collins <[EMAIL PROTECTED]>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AMD 8151 AGP Bridge rev B3
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xf0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: HPC vendor_id 1022 device_id 7455 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: HPC vendor_id 1022 device_id 7460 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
AMD8111: IDE controller at PCI slot 0000:00:07.1
AMD8111: chipset revision 3
AMD8111: not 100% native mode: will probe irqs later
AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
AMD8111: port 0x01f0 already claimed by ide0
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hw_random: AMD768 system management I/O registers at 0x5000.
hw_random hardware driver 1.0.0 loaded
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:01:00.0[D] -> GSI 19 (level, low) -> IRQ 169
ohci_hcd 0000:01:00.0: Advanced Micro Devices [AMD] AMD-8111 USB
ohci_hcd 0000:01:00.0: irq 169, pci mem f8bb8000
ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:01:00.1[D] -> GSI 19 (level, low) -> IRQ 169
ohci_hcd 0000:01:00.1: Advanced Micro Devices [AMD] AMD-8111 USB (#2)
ohci_hcd 0000:01:00.1: irq 169, pci mem f8bba000
ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 17 (level, low) -> IRQ 193
uhci_hcd 0000:01:0b.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:01:0b.0: irq 193, io base 00009800
uhci_hcd 0000:01:0b.0: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:01:0b.1[B] -> GSI 18 (level, low) -> IRQ 185
uhci_hcd 0000:01:0b.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#2)
uhci_hcd 0000:01:0b.1: irq 185, io base 00009c00
uhci_hcd 0000:01:0b.1: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0316d00(lo)
IPv6 over IPv4 tunneling driver
parport0: PC-style at 0x378 [PCSPP]
lp0: using parport0 (polling).
NET: Registered protocol family 17
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
eth0: no IPv6 routers present
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System
Controller (rev 14)
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge (rev
14)
0000:00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
0000:00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:01:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
0000:01:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
0000:01:03.0 Ethernet controller: Intel Corp. 82541EI Gigabit Ethernet
Controller (Copper)
0000:01:05.0 Unknown mass storage controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
0000:01:09.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
Modem/ISDN interface
0000:01:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80)
0000:01:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61)
0000:01:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61)
0000:01:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 62)
0000:02:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX
4000 AGP 8x] (rev a4)
Module Size Used by
tsdev 7872 0
mousedev 10960 1
psmouse 20680 0
nvidia 4822900 12
snd_pcm_oss 55400 0
snd_pcm 101892 1 snd_pcm_oss
snd_page_alloc 12168 1 snd_pcm
snd_timer 27460 1 snd_pcm
snd_mixer_oss 20416 1 snd_pcm_oss
snd 60132 4 snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore 11168 1 snd
nfsd 203872 8
exportfs 7488 1 nfsd
lockd 65736 2 nfsd
sunrpc 159204 2 nfsd,lockd
af_packet 24200 2
parport_pc 36544 1
lp 11464 0
parport 43272 2 parport_pc,lp
autofs4 21508 2
ipv6 279812 16
uhci_hcd 33936 0
ohci_hcd 22532 0
hw_random 6228 0
amd74xx 14556 1
shpchp 101964 0
pciehp 98444 0
pci_hotplug 35580 2 shpchp,pciehp
amd64_agp 11656 1
agpgart 35500 2 amd64_agp
evdev 10048 0
eth1394 23048 0
hisax 595280 0
crc_ccitt 2624 1 hisax
isdn 150604 1 hisax
slhc 8320 1 isdn
ehci_hcd 32772 0
usbcore 121764 5 uhci_hcd,ohci_hcd,ehci_hcd
e1000 86020 0
ohci1394 36932 0
md 51208 0
capability 5064 0
commoncap 7808 1 capability
sr_mod 18084 0
sbp2 25160 0
ieee1394 113720 3 eth1394,ohci1394,sbp2
ide_cd 43296 0
cdrom 40860 2 sr_mod,ide_cd
ide_generic 1920 0
ide_core 141660 3 amd74xx,ide_cd,ide_generic
rtc 14408 0
jfs 188888 2
ext2 74536 0
ext3 129448 0
jbd 69976 1 ext3
mbcache 10500 2 ext2,ext3
sd_mod 22272 4
sata_sil 8452 3
libata 41924 1 sata_sil
scsi_mod 127684 4 sr_mod,sbp2,sd_mod,libata
unix 31316 226
font 8896 0
vesafb 7136 0
cfbcopyarea 4224 1 vesafb
cfbimgblt 3520 1 vesafb
cfbfillrect 4160 1 vesafb
