Package: kernel Severity: normal Second attempt to load module aic79xx causes the following: # modprobe aic79xx kobject_register failed for aic79xx (-17) [<c01b32db>] kobject_register+0x5b/0x60 [<c02068e0>] bus_add_driver+0x50/0xc0 [<c01be1dc>] pci_register_driver+0x6c/0xa0 [<f8a766bf>] ahd_linux_pci_init+0xf/0x20 [aic79xx] [<f8a6d725>] ahd_linux_detect+0x45/0x90 [aic79xx] [<f882400f>] ahd_linux_init+0xf/0x24 [aic79xx] [<c013a2f1>] sys_init_module+0x111/0x240 [<c01061f9>] sysenter_past_esp+0x52/0x71
hotplug package seems to try to load aic79xx multiple times which causes a boot failure. (Should I raise a bug report for hotplug too?). Removing hotplug package allows normal boot. This problem does not occur with 2.6.6-2 but does with 2.6.7 and 2.6.8 Two boot logs are included, one a failure with hotplug the second with boot param: init=/bin/bash and a manual load of aic79xx. -- System Information: Debian Release: 3.1 APT prefers unstable APT policy: (500, 'unstable') Architecture: i386 (i686) Kernel: Linux 2.6.8-1-k7-smp Locale: LANG=C, LC_CTYPE=C
BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e800 (usable) BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fef0000 (usable) BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data) BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS) BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable) BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. found SMP MP-table at 000f7170 DMI 2.3 present. ACPI: RSDP (v000 PTLTD ) @ 0x000f7100 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3fefcf28 ACPI: FADT (v001 AMD TECATE 0x06040000 PTL 0x000f4240) @ 0x3fefef2e ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3fefefa2 ACPI: DSDT (v001 AMD AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x8008 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled) Processor #1 6:8 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 16 WARNING: NR_CPUS limit of 1 reached. Processor ignored. ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Built 1 zonelists Kernel command line: root=/dev/sda2 ro console=ttyS0,115200 Initializing CPU#0 PID hash table entries: 4096 (order 12: 32768 bytes) Detected 2000.282 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 901824k/917504k available (1329k kernel code, 14904k reserved, 727k data, 204k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3956.73 BogoMIPS Security Scaffold v1.0.0 initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: AMD Athlon(tm) MP 2400+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. Checking for popad bug... OK. masked ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs ...TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. calibrating APIC timer ... ...... CPU clock speed is 1999.0790 MHz. ...... host bus clock speed is 266.0638 MHz. checking if image is initramfs...it isn't (ungzip failed); looks like an initrd Freeing initrd memory: 4328k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=3 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9 ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11) Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f7130 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9aad, dseg 0x400 PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver PCI: Using ACPI for IRQ routing ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169 ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 21 (level, low) -> IRQ 177 ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 18 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 16 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:03:04.1[B] -> GSI 17 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 17 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 18 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:03:06.1[B] -> GSI 19 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:03:06.2[C] -> GSI 16 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:03:07.0[A] -> GSI 19 (level, low) -> IRQ 193 testing the IO APIC....................... Using vector-based indexing ..................................... done. VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED]) devfs: boot_options: 0x0 Initializing Cryptographic API BIOS failed to enable PCI standards compliance, fixing this error. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 EISA: Probing bus 0 at eisa0 Cannot allocate resource for EISA slot 1 Cannot allocate resource for EISA slot 2 EISA: Detected 0 cards. NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: (supports S0 S1 S4 S5) RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 4328 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-done. VFS: Mounted root (cramfs filesystem) readonly. Freeing unused kernel memory: 204k freed initrd-tools: 0.1.73 SCSI subsystem initialized ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 16 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:03:04.1[B] -> GSI 17 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 17 (level, low) -> IRQ 209 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 3960D Ultra160 SCSI adapter> aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs Using anticipatory io scheduler (scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) Vendor: FUJITSU Model: MAN3367MP Rev: 0107 Type: Direct-Access ANSI SCSI revision: 03 scsi0:A:1:0: Tagged Queuing enabled. Depth 8 scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 3960D Ultra160 SCSI adapter> aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 2940 Ultra SCSI adapter> aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs (scsi2:A:4): 20.000MB/s transfers (20.000MHz, offset 8) Vendor: GENERIC Model: CRD-BP2 Rev: 2.21 Type: CD-ROM ANSI SCSI revision: 02 (scsi2:A:5): 10.000MB/s transfers (10.000MHz, offset 15) Vendor: MATSHITA Model: DVD-RAM LF-D200 Rev: X120 Type: CD-ROM ANSI SCSI revision: 04 vesafb: probe of vesafb0 failed with error -6 NET: Registered protocol family 1 Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0 Attached scsi generic sg1 at scsi2, channel 0, id 4, lun 0, type 5 Attached scsi generic sg2 at scsi2, channel 0, id 5, lun 0, type 5 SCSI device sda: 71771688 512-byte hdwr sectors (36747 MB) SCSI device sda: drive cache: write back /dev/scsi/host0/bus0/target1/lun0: p1 p2 p3 < p5 p6 p7 p8 > Attached scsi disk sda at scsi0, channel 0, id 1, lun 0 SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. INIT: version 2.86 booting Setting disc parameters: done. Activating swap. Adding 1172704k swap on /dev/sda5. Priority:-1 extents:1 Checking root file system... fsck 1.35 (28-Feb-2004) /dev/sda2: clean, 23565/124928 files, 446905/498EXT3 FS on sda2, internal journal 012 blocks /etc/init.d/rcS: System clock was not updated at this time. Cleaning up ifupdown...done. WARNING: Bastille-firewall is not configured yet Please create /etc/Bastille/bastille-firewall.cfg to enable it. (HINT: use InteractiveBastille) Calculating module dependencies... done. Loading modules... e1000 e1000: Ignoring new-style parameters in presence of obsolete ones Intel(R) PRO/1000 Network Driver - version 5.2.52-k4 Copyright (c) 1999-2004 Intel Corporation. ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection All modules loaded. Capability LSM initialized device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED] Creating device-mapper devices...done. Checking all file systems... fsck 1.35 (28-Feb-2004) /dev/sda6: recovering journal /dev/sda6: clean, 177587/750720 files, 931761/1500061 blocks /dev/sda7: recovering journal /dev/sda7: clean, 22270/377856 files, 162431/755047 blocks (check in 2 mounts) Setting kernel variables ... .... done. Mounting local filesystems... kjournald starting. Commit interval 5 seconds EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald st/dev/sda6 on /usr type ext3 (rw) /dev/sda7 on /var type ext3 (rw) arting. Commit interval 5 seconds EXT3 FS on sda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. Setting sensors limits:Can't access procfs/sysfs file Unable to find i2c bus information; For 2.6 kernels, make sure you have mounted sysfs and done 'modprobe i2c_sensor'! For older kernels, make sure you have done 'modprobe i2c-proc'! Can't access procfs/sysfs file Unable to find i2c bus information; For 2.6 kernels, make sure you have mounted sysfs and done 'modprobe i2c_sensor'! For older kernels, make sure you have done 'modprobe i2c-proc'! done. Running 0dns-down to make sure resolv.conf is ok...done. /dev/shm/network/...Initializing: /etc/network/ifstate. Starting hotplug subsystem: input evbug: blacklisted evdev: loaded successfully evbug: blacklisted evdev: already loaded input [success] isapnp Real Time Clock Driver v1.12 rtc: loaded sucessfully input: PC Speaker pcspkr: loaded sucessfully input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 mice: PS/2 mouse device common for all mice psmouse: loaded sucessfully ts: Compaq touchscreen protocol output parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] parport_pc: loaded sucessfully inserting floppy driver for 2.6.8-1-386 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 floppy: loaded sucessfully isapnp [success] net net [success] pci Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected AMD 760MP chipset agpgart: Maximum main memory to use for agp memory: 816M agpgart: AGP aperture is 64M @ 0xf0000000 amd-k7-agp: loaded successfully cpci_hotplug: CompactPCI Hot Plug Core version: 0.2 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5 pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5 modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted pciehp: can't be loaded missing kernel or user mode driver pciehp shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted shpchp: can't be loaded missing kernel or user mode driver shpchp amd76xrom amd76xrom_init_one(): Unable to register resource 0xffb00000-0xffffffff - kernel bug? amd76xrom window : 500000 at ffb00000 CFI: Found no amd76xrom device at location zero JEDEC: Found no amd76xrom device at location zero CFI: Found no amd76xrom device at location zero JEDEC: Found no amd76xrom device at location zero CFI: Found no amd76xrom device at location zero JEDEC: Found no amd76xrom device at location zero CFI: Found no amd76xrom device at location zero JEDEC: Found no amd76xrom device at location zero CFI: Found no amd76xrom device at location zero Found: PMC Pm49FL004 amd76xrom: Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. amd76xrom chip at offset: 0x480000 amd76xrom: cannot reserve MTD resource amd76xrom: loaded successfully Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx amd74xx: loaded successfully hw_random: AMD768 system management I/O registers at 0x8000. hw_random hardware driver 1.0.0 loaded hw_random: loaded successfully e1000: already loaded Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 21 (level, low) -> IRQ 177 Adaptec I2O RAID controller 0 at f8ffa000 size=100000 irq=177 dpti: If you have a lot of devices this could take a few minutes. dpti0: Reading the hardware resource table. TID 008 Vendor: ADAPTEC Device: AIC-7899 Rev: 00000001 scsi3 : Vendor: Adaptec Model: 2110S FW:380E dpt_i2o: loaded successfully pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5 pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5 modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted pciehp: can't be loaded missing kernel or user mode driver pciehp shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted shpchp: can't be loaded missing kernel or user mode driver shpchp pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5 pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5 modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted pciehp: can't be loaded missing kernel or user mode driver pciehp shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-386/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted shpchp: can't be loaded missing kernel or user mode driver shpchp ignoring pci display device on 01:05.0 usbcore: registered new driver usbfs usbcore: registered new driver hub ACPI: PCI interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 193 ohci_hcd 0000:03:00.0: Advanced Micro Devices [AMD] AMD-768 [Opus] USB ohci_hcd 0000:03:00.0: irq 193, pci mem f8977000 ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 18 (level, low) -> IRQ 185 ohci_hcd 0000:03:06.0: NEC Corporation USB ohci_hcd 0000:03:06.0: irq 185, pci mem f8fa9000 ohci_hcd 0000:03:06.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ACPI: PCI interrupt 0000:03:06.1[B] -> GSI 19 (level, low) -> IRQ 193 ohci_hcd 0000:03:06.1: NEC Corporation USB (#2) ohci_hcd 0000:03:06.1: irq 193, pci mem f8fab000 ohci_hcd 0000:03:06.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ohci-hcd: loaded successfully modprobe: FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-386/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device aic79xx: can't be loaded missing kernel or user mode driver aic79xx aic7xxx: already loaded kobject_register failed for aic79xx (-17) [<c018b8d3>] kobject_register+0x35/0x3d [<c01d2f68>] bus_add_driver+0x38/0x70 [<c01d32d7>] driver_register+0x2d/0x31 [<c0193a7a>] pci_register_driver+0x4e/0x6b [<f91a74e5>] ahd_linux_pci_init+0xa/0x12 [aic79xx] [<f91a07ed>] ahd_linux_detect+0x3c/0x6c [aic79xx] [<f897500a>] ahd_linux_init+0xa/0x19 [aic79xx] [<c012af8c>] sys_init_module+0xe3/0x1d4 [<c0105f45>] sysenter_past_esp+0x52/0x71 modprobe: FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-386/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device aic79xx: can't be loaded missing kernel or user mode driver aic79xx aic7xxx: already loaded aic7xxx: already loaded ohci-hcd: already loaded ohci-hcd: already loaded Unable to handle kernel paging request at virtual address f91c2ab8 printing eip: c018b855 *pde = 370cf067 *pte = 00000000 Oops: 0002 [#1] PREEMPT Modules linked in: ehci_hcd ohci_hcd usbcore dpt_i2o hw_random amd74xx ide_core cfi_cmdset_0002 cfi_util mtdpart jedec_probe cfi_probe gen_probe amd76xrom mtdcore chipreg map_funcs pci_hotplug amd_k7_agp agpgart floppy parport_pc tsdev parport mousedev psmouse pcspkr rtc evdev dm_mod capability commoncap e1000 xfs ext3 jbd sd_mod sg unix font vesafb cfbcopyarea cfbimgblt cfbfillrect aic7xxx scsi_mod CPU: 0 EIP: 0060:[<c018b855>] Not tainted EFLAGS: 00010296 (2.6.8-1-386) EIP is at kobject_add+0x67/0xb0 eax: c02c19c0 ebx: f9101a3c ecx: f91c2ab8 edx: f9101a58 esi: c02c19c8 edi: f9101a24 ebp: 00000000 esp: f6a0ff40 ds: 007b es: 007b ss: 0068 Process modprobe (pid: 1815, threadinfo=f6a0e000 task=f6ce20f0) Stack: f9101a3c ffffffea f9101a24 c018b8b9 f9101a3c f9101a3c f9101a3c c02c1960 c01d2f68 f9101a3c f9101a00 00000000 f9101a98 c0289e00 c01d32d7 f9101a24 f8fd6b4a f8fd1000 00000000 c0279124 c0193a7a f9101a24 c0289e18 f9101b00 Call Trace: [<c018b8b9>] kobject_register+0x1b/0x3d [<c01d2f68>] bus_add_driver+0x38/0x70 [<c01d32d7>] driver_register+0x2d/0x31 [<c0193a7a>] pci_register_driver+0x4e/0x6b [<f8975018>] init+0x18/0x24 [ehci_hcd] [<c012af8c>] sys_init_module+0xe3/0x1d4 [<c0105f45>] sysenter_past_esp+0x52/0x71 Code: 89 11 89 4a 04 8b 43 28 8b 00 83 c0 48 e8 35 14 00 00 89 73 ./hotplug.functions: line 140: 1815 Segmentation fault $MODPROBE $MODULE >/dev/null 2>&1 ehci-hcd: can't be loaded missing kernel or user mode driver ehci-hcd emu10k1: blacklisted
BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fef0000 (usable) BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data) BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS) BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable) BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f7170 DMI 2.3 present. ACPI: RSDP (v000 PTLTD ) @ 0x000f7100 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3fefcf28 ACPI: FADT (v001 AMD TECATE 0x06040000 PTL 0x000f4240) @ 0x3fefef2e ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3fefefa2 ACPI: DSDT (v001 AMD AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x8008 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled) Processor #1 6:8 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Built 1 zonelists Kernel command line: root=/dev/sda2 ro console=ttyS0,115200 init=/bin/bash Initializing CPU#0 PID hash table entries: 4096 (order 12: 32768 bytes) Detected 2000.474 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1030132k/1048064k available (1636k kernel code, 16956k reserved, 775k data, 168k init, 130496k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3956.73 BogoMIPS Security Scaffold v1.0.0 initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: AMD Athlon(tm) MP 2400+ stepping 01 per-CPU timeslice cutoff: 731.38 usecs. task migration cache decay timeout: 1 msecs. masked ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Booting processor 1/0 eip 3000 Initializing CPU#1 masked ExtINT on CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 3997.69 BogoMIPS CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Athlon(tm) Processor stepping 01 Total of 2 processors activated (7954.43 BogoMIPS). ENABLING IO-APIC IRQs ...TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. calibrating APIC timer ... ...... CPU clock speed is 1999.0725 MHz. ...... host bus clock speed is 266.0630 MHz. checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs checking if image is initramfs...it isn't (ungzip failed); looks like an initrd Freeing initrd memory: 4724k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) mtrr: your CPUs had inconsistent fixed MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: Subsystem revision 20040326 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9 ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11) Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f7130 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9aad, dseg 0x400 PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver PCI: Using ACPI for IRQ routing ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169 ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 18 (level, low) -> IRQ 177 ACPI: PCI interrupt 0000:02:00.0[D] -> GSI 19 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 17 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 177 ACPI: PCI interrupt 0000:02:06.1[B] -> GSI 19 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:02:06.2[C] -> GSI 16 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 19 (level, low) -> IRQ 185 testing the IO APIC....................... Using vector-based indexing ..................................... done. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED]) devfs: boot_options: 0x0 Initializing Cryptographic API BIOS failed to enable PCI standards compliance, fixing this error. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: (supports S0 S1 S4 S5) RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 4724 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done. VFS: Mounted root (cramfs filesystem) readonly. Freeing unused kernel memory: 168k freed initrd-tools: 0.1.74 SCSI subsystem initialized ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 17 (level, low) -> IRQ 201 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 3960D Ultra160 SCSI adapter> aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs Using anticipatory io scheduler (scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit) Vendor: FUJITSU Model: MAN3367MP Rev: 0107 Type: Direct-Access ANSI SCSI revision: 03 scsi0:A:1:0: Tagged Queuing enabled. Depth 8 scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 3960D Ultra160 SCSI adapter> aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs vesafb: probe of vesafb0 failed with error -6 NET: Registered protocol family 1 Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 0 SCSI device sda: 71771688 512-byte hdwr sectors (36747 MB) SCSI device sda: drive cache: write back /dev/scsi/host0/bus0/target1/lun0: p1 p2 p3 < p5 p6 p7 p8 > Attached scsi disk sda at scsi0, channel 0, id 1, lun 0 SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled SGI XFS Quota Management subsystem kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. root@(none):/# modprobe aic79xx FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device root@(none):/# mount /proc root@(none):/# lsmod Module Size Used by xfs 621596 0 ext3 129448 1 jbd 69976 1 ext3 mbcache 10500 1 ext3 sd_mod 22272 2 sg 40224 0 unix 31316 0 font 8896 0 vesafb 7136 0 cfbcopyarea 4224 1 vesafb cfbimgblt 3520 1 vesafb cfbfillrect 4160 1 vesafb aic7xxx 207256 1 scsi_mod 127556 3 sd_mod,sg,aic7xxx root@(none):/# modprobe aic79xx kobject_register failed for aic79xx (-17) [<c01b32db>] kobject_register+0x5b/0x60 [<c02068e0>] bus_add_driver+0x50/0xc0 [<c01be1dc>] pci_register_driver+0x6c/0xa0 [<f8a766bf>] ahd_linux_pci_init+0xf/0x20 [aic79xx] [<f8a6d725>] ahd_linux_detect+0x45/0x90 [aic79xx] [<f882400f>] ahd_linux_init+0xf/0x24 [aic79xx] [<c013a2f1>] sys_init_module+0x111/0x240 [<c01061f9>] sysenter_past_esp+0x52/0x71 FATAL: Error inserting aic79xx (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/scsi/aic7xxx/aic79xx.ko): No such device root@(none):/# lsmod Module Size Used by xfs 621596 0 ext3 129448 1 jbd 69976 1 ext3 mbcache 10500 1 ext3 sd_mod 22272 2 sg 40224 0 unix 31316 0 font 8896 0 vesafb 7136 0 cfbcopyarea 4224 1 vesafb cfbimgblt 3520 1 vesafb cfbfillrect 4160 1 vesafb aic7xxx 207256 1 scsi_mod 127556 3 sd_mod,sg,aic7xxx root@(none):/#