Package: kernel-image-2.6.10-1-686
Version: 2.6.10-4
Severity: normal
Hi, kernel-image-2.6.10-1-686 freezes for about 30 sec. during the
boot procces, just after the message:
ide1 at 0x170-0x177,0x376 on irq 15
After that, the boot proccess continues but a bunch of error
messages with modules are shown; something like this:
ERROR: Removing 'rz1000': Device or resource busy
These error messages are shown just before the message:
EXT3-fs: mounted filesystem with ordered data mode.
(But they are not shown in dmesg!)
Finally, the boot proccess ends normally, and everything works fine.
lspci -vv output:
0000:00:00.0 Host bridge: Intel Corp. 82852/855GM Host Bridge (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] #09 [0105]
0000:00:00.1 System peripheral: Intel Corp. 855GM/GME GMCH Memory I/O Control
Registers (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:00.3 System peripheral: Intel Corp. 855GM/GME GMCH Configuration
Process Registers (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
0000:00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated
Graphics Device (rev 02) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device 0002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 193
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at eff8 [size=8]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics
Device (rev 02)
Subsystem: Toshiba America Info Systems: Unknown device 0002
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Region 0: Memory at 20000000 (32-bit, prefetchable) [disabled]
[size=128M]
Region 1: Memory at 1f000000 (32-bit, non-prefetchable) [disabled]
[size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 193
Region 4: I/O ports at cfe0 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 201
Region 4: I/O ports at cf80 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI
Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 209
Region 0: Memory at 1f080000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 83) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: cff00000-cfffffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage
Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at bfa0 [size=16]
Region 5: Memory at 1f080400 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
Subsystem: Toshiba America Info Systems: Unknown device 0241
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 169
Region 0: I/O ports at 1000 [size=256]
Region 1: I/O ports at 1400 [size=64]
Region 2: Memory at 1f080800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at 1f080a00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1f.6 Modem: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97
Modem Controller (rev 03) (prog-if 00 [Generic])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 169
Region 0: I/O ports at 1800 [size=256]
Region 1: I/O ports at 1480 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:08.0 Ethernet controller: Intel Corp. 82801BD PRO/100 VE (MOB) Ethernet
Controller (rev 83)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 185
Region 0: Memory at cffff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at cf40 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:01:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to
Cardbus Bridge with ZV Support (rev 33)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 177
Region 0: Memory at 1f081000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=01, secondary=02, subordinate=05, sec-latency=0
Memory window 0: 1f400000-1f7ff000 (prefetchable)
Memory window 1: 1f800000-1fbff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
dmesg output:
00000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ef40000 (usable)
BIOS-e820: 000000001ef40000 - 000000001ef50000 (ACPI data)
BIOS-e820: 000000001ef50000 - 000000001f000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
495MB LOWMEM available.
On node 0 totalpages: 126784
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 122688 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f0180
ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef40000
ACPI: FADT (v002 TOSHIB 750 0x20030101 TASM 0x04010000) @ 0x1ef40060
ACPI: SSDT (v001 TOSHIB A000C 0x20030917 MSFT 0x0100000e) @ 0x1ef402ca
ACPI: DBGP (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef400e4
ACPI: BOOT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef40038
ACPI: MADT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef40118
ACPI: DSDT (v001 TOSHIB A000C 0x20031216 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0xd808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda5 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2793.356 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 494724k/507136k available (1682k kernel code, 11788k reserved, 704k
data, 172k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5537.79 BogoMIPS (lpj=2768896)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400
00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
CPU: Intel Mobile Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
...TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like
an initrd
Freeing initrd memory: 4596k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd2fe, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [EMAIL PROTECTED]
** so I can fix the driver.
Simple Boot Flag at 0x7c set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
PCI: Enabling device 0000:00:1f.6 (0000 -> 0001)
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 169
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
VIY0 USB1 USB2 USB4 AMDM LID PWRB
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4596KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 172k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 177
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK4025GAS, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 < p5 p6 p7 p8 >
Probing IDE interface ide1...
hdc: UJDA750 DVD/CDRW, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 618460k swap on /dev/hda7. Priority:-1 extents:1
EXT3 FS on hda5, internal journal
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Fan [FAN] (off)
ACPI: Processor [CPU0] (supports C1 C2 C3)
mice: PS/2 mouse device common for all mice
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (3962 buckets, 31696 max) - 336 bytes per conntrack
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.6
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: SCO (Voice Link) ver 0.3
Bluetooth: SCO socket layer initialized
Toshiba System Managment Mode driver v1.11 26/9/2001
input: PS/2 Generic Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Capability LSM initialized
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug
enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem hda6
Ending clean XFS mount for filesystem: hda6
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:01:0b.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 18 (level, low) -> IRQ 177
Yenta: CardBus bridge found at 0000:01:0b.0 [1179:0001]
Yenta: ISA IRQ mask 0x04b8, PCI irq 177
Socket status: 30000007
e100: Intel(R) PRO/100 Network Driver, 3.2.3-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 185
e100: eth0: e100_probe: addr 0xcffff000, irq 185, MAC addr 00:08:0D:83:BF:D5
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 193
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB
UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 193, io base 0xcfe0
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB
UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 201, io base 0xcf80
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
input: Logitech USB-PS/2 Optical Mouse on usb-0000:00:1d.0-1
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 209
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI
Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 209, pci mem 0x1f080000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usb 1-1: USB disconnect, address 2
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usb 1-1: new low speed USB device using uhci_hcd and address 3
input: Logitech USB-PS/2 Optical Mouse on usb-0000:00:1d.0-1
pnp: Evaluate _CRS failed
pnp: Failed to activate device 00:08.
parport_pc: probe of 00:08 failed with error -5
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Maximum main memory to use for agp memory: 424M
agpgart: Detected 16252K stolen memory.
agpgart: AGP aperture is 128M @ 0xd8000000
hw_random: RNG not detected
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
PCI: Enabling device 0000:00:1f.5 (0000 -> 0003)
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49394 usecs
intel8x0: clocking to 48000
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.6 to 64
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<[EMAIL PROTECTED]> and others
e100: eth0: e100_watchdog: link up, 10Mbps, full-duplex
NET: Registered protocol family 17
IN=eth0 OUT= MAC=00:08:0d:83:bf:d5:00:03:4b:15:40:72:08:00 SRC=80.221.213.223
DST=80.221.28.196 LEN=48 TOS=0x00 PREC=0x00 TTL=121 ID=13820 DF PROTO=TCP
SPT=4530 DPT=135 WINDOW=16384 RES=0x00 SYN URGP=0
IN=eth0 OUT= MAC=00:08:0d:83:bf:d5:00:03:4b:15:40:72:08:00 SRC=83.36.164.38
DST=80.221.28.196 LEN=53 TOS=0x00 PREC=0x20 TTL=45 ID=50117 DF PROTO=UDP
SPT=7484 DPT=10010 LEN=33
IN=eth0 OUT= MAC=00:08:0d:83:bf:d5:00:03:4b:15:40:72:08:00 SRC=194.251.255.72
DST=80.221.28.196 LEN=48 TOS=0x00 PREC=0x00 TTL=251 ID=55835 DF PROTO=ICMP
TYPE=8 CODE=0 ID=12112 SEQ=0
IN=eth0 OUT= MAC=00:08:0d:83:bf:d5:00:03:4b:15:40:72:08:00 SRC=80.221.213.223
DST=80.221.28.196 LEN=48 TOS=0x00 PREC=0x00 TTL=121 ID=14043 DF PROTO=TCP
SPT=4530 DPT=135 WINDOW=16384 RES=0x00 SYN URGP=0
IN=eth0 OUT= MAC= SRC=80.221.28.196 DST=224.0.0.251 LEN=74 TOS=0x00 PREC=0x00
TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=54
cs: IO port probe 0x0100-0x04ff: excluding 0x1e0-0x1e7 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c032abe0(lo)
IPv6 over IPv4 tunneling driver
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 193
[drm] Initialized i830 1.3.2 20021108 on minor 0: Intel Corp. 82852/855GM
Integrated Graphics Device
PCI: Enabling device 0000:00:02.1 (0000 -> 0002)
[drm] Initialized i830 1.3.2 20021108 on minor 1: Intel Corp. 82852/855GM
Integrated Graphics Device (#2)
mtrr: base(0xd8020000) is not aligned on a size(0x300000) boundary
eth0: no IPv6 routers present
-- System Information:
Debian Release: 3.1
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.10-1-686
Locale: [EMAIL PROTECTED], [EMAIL PROTECTED] (charmap=ISO-8859-15)
Versions of packages kernel-image-2.6.10-1-686 depends on:
ii coreutils [fileutils] 5.2.1-2 The GNU core utilities
ii initrd-tools 0.1.77 tools to create initrd image for p
ii module-init-tools 3.2-pre1-1 tools for managing Linux kernel mo
-- no debconf information
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
