On Fri, 24 Feb 2006 11:26:17 +0100
Gollum1 <[EMAIL PROTECTED]> wrote:
> 1) non viene rilevato da udev al boot... e la cosa mi pare strana, prova a
> guardare dmesg.
>
> 2) manca per qualche motivo il modulo di kernel che gestisce il floppy
> (strano, visto che dovrebbe essere caricato di default, e comunque caricato
> da udev se lo trova come hardware)
>
da dove lo vedo ho provato da synaptic se c'era qualche modulo aggiuntivo
da installare ma non ne ho trovati
>
> credo che il primo passo da fare sia andare a guardare dmesg per sapere se
> almeno al boot viene visto...
Sembrerebbe di si... ma...
debian:~# dmesg
Linux version 2.6.8-2-k7 ([EMAIL PROTECTED]) (gcc version 3.3.5 (Debian
1:3.3.5-13)) #1 Tue Aug 16 14:00:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000eff0000 (usable)
BIOS-e820: 000000000eff0000 - 000000000effffc0 (ACPI data)
BIOS-e820: 000000000effffc0 - 000000000f000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
239MB LOWMEM available.
On node 0 totalpages: 61424
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 57328 pages, LIFO batch:13
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 OID_00 ) @ 0x000e4010
ACPI: RSDT (v001 OID_00 RSDT_000 0x30303030 _CSI 0x00010101) @ 0x0efffbc0
ACPI: FADT (v001 INSYDE FACP_000 0x00000100 _CSI 0x00010101) @ 0x0efffac0
ACPI: BOOT (v001 INSYDE SYS_BOOT 0x00000100 _CSI 0x00010101) @ 0x0efffb50
ACPI: DBGP (v001 INSYDE SYS_DBGP 0x00000100 _CSI 0x00010101) @ 0x0efffb80
ACPI: DSDT (v001 INSYDE VT8362 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Built 1 zonelists
Kernel command line: root=/dev/hda2 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1533.349 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 235716k/245696k available (1536k kernel code, 9268k reserved, 697k
data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3039.23 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0183fbff c1cbfbff 00000000 00000000
CPU: After vendor identify, caps: 0183fbff c1cbfbff 00000000 00000000
Enabling disabled K7/SSE Support.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD mobile AMD Athlon(tm) XP 1800+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1533.0143 MHz.
..... host bus clock speed is 266.0633 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4496k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xe8a64, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
spurious 8259A interrupt: IRQ7.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 80): [55] 3c & 1f -> 1c
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 1)
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00ff020
PnPBIOS: PnP BIOS version 1.0, entry 0xea000:0x327e, dseg 0xea000
PnPBIOS: dev_node_info: function not supported on this system
PnPBIOS: Unable to get node info. Aborting.
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:11.6[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Cannot allocate resource region 0 of device 0000:00:0a.0
Simple Boot Flag at 0x37 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
Initializing Cryptographic API
Applying VIA southbridge workaround.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S3 S4 S4bios S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4496 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1
ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N020ATCS04-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 >
hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 530104k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda2, internal journal
ide-floppy driver 0.99.newide
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
input: PS/2 Generic Mouse on isa0060/serio4
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver snd-usb-audio
Capability LSM initialized
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.100 (c) Dave Jones
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0a.0 [1025:001d]
Yenta: ISA IRQ mask 0x0038, PCI irq 11
Socket status: 30000821
irda_init()
NET: Registered protocol family 23
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
PCI: Enabling device 0000:00:12.0 (0001 -> 0003)
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0xe800, 00:c0:9f:20:3d:f7, IRQ 11.
eth0: MII PHY found at address 1, status 0x7829 advertising 01e1 Link 45e1.
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp: pci dev 0000:02:00.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible
chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth1: RealTek RTL8139 at 0x4000, 00:02:44:57:83:d1, IRQ 11
eth1: Identified 8139 chip type 'RTL-8139C'
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:11.2: irq 11, io base 00001200
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using address 2
usb 1-2: new full speed USB device using address 3
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [ARESON USB Scroll Mouse] on usb-0000:00:11.2-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Linux video capture interface: v1.00
quickcam: QuickCam USB camera found (driver version QuickCam USB 0.6.3 $Date:
2005/04/15 19:32:49 $)
quickcam: Kernel:2.6.8-2-k7 bus:1 class:FF subclass:FF vendor:046D product:0850
quickcam: Sensor VV6410 detected
quickcam: Registered device: /dev/video0
usbcore: registered new driver quickcam
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: Maximum main memory to use for agp memory: 189M
agpgart: AGP aperture is 64M @ 0xa0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO
[PCSPP,TRISTATE,COMPAT,ECP]
parport_pc: VIA parallel port: io=0x378, irq=7
hsfengine: module license 'see LICENSE file distributed with driver' taints
kernel.
ACPI: PCI interrupt 0000:00:11.6[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.6 to 64
ttySHSF0 at I/O 0xe200 (irq = 10) is a Conexant HSF softmodem
(PCI-1106:3068-1025:001d)
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02fc1a0(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 24
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Thermal Zone [THRM] (66 C)
lp0: using parport0 (interrupt-driven).
eth0: no IPv6 routers present
cs: IO port probe 0x0100-0x04ff: excluding 0x2c8-0x2cf 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
ip_tables: (C) 2000-2002 Netfilter core team
mtrr: no more MTRRs available
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
Ciao David
--
Per REVOCARE l'iscrizione alla lista, inviare un email a
[EMAIL PROTECTED] con oggetto "unsubscribe". Per
problemi inviare un email in INGLESE a [EMAIL PROTECTED]
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
