Dear Lucas,
I tried with linear and my debian just boot! I'm sending to you my lilo.conf file (in
case
it seems to you useful for your how-to with LILO) after making some changes that
"lilo-doc" recommended for raid booting.
As I thought it couldn't be the only problem... Could you take a look to the following?
Note: Not all the devices are synchronized at this time. Sorry about this (It takes 7
hours each time I have to do it again...). Perhaps I just have to wait???
Thanks for everything!!!
Agustín
maria:/# mdadm -D /dev/md1
/dev/md1:
Version : 00.90.00
Creation Time : Wed Sep 8 22:31:30 2004
Raid Level : raid1
Array Size : 14464 (14.12 MiB 14.81 MB)
Device Size : 14464 (14.12 MiB 14.81 MB)
Raid Disks : 2
Total Disks : 3
Preferred Minor : 1
Persistance : Superblock is persistant
Update Time : Wed Sep 8 23:03:53 2004
State : dirty, no-errors
Active Drives : 2
Working Drives : 2
***** Failed Drives : 1 *****
Spare Drives : 0
Number Major Minor RaidDisk State
0 3 1 0 active sync /dev/hda1
1 22 1 1 active sync /dev/hdc1
UUID : 2bf99542:45c208ee:df7011a5:0e8b602f
maria:/# mdadm -E /dev/md1
****** mdadm: No super block found on /dev/md1 (Expected magic a92b4efc, got 00000000)
******
maria:/# cat /proc/mdstat
Personalities : [raid1]
read_ahead 1024 sectors
md1 : active raid1 hda1[0] hdc1[1]
14464 blocks [2/2] [UU]
----- Original Message -----
From: "Lucas Albers" <[EMAIL PROTECTED]>
To: "Agustín Ciciliani" <[EMAIL PROTECTED]>
Sent: Wednesday, September 08, 2004 5:57 PM
Subject: Re: RAID 1 HELP!!!
> Try using grub or run lilo with lba or linear mode.
> My guess is that it is not seeing the sata drives correctly.
> Try running a newer kernel that has better sata support.
>
> Agustín Ciciliani said:
> > Dear Lucas,
> >
> > I hope not to bother with my question. I've been reading your excellent
> > how-to:
> >
> > Version 0.97 (2004-06-03) Lucas Albers -- admin At cs DOT montana dot edu
> > and Roger
> > Chrisman
> > Home of most recent version: http://alioth.debian.org/projects/rootraiddoc
> >
> > I really think that it is the best raid 1 how-to in the web.
> >
> > Everything works fine, exactly as you describe it (I've read EVERYTHING
> > three times) until
> > the step 6.3. I make the 6.4 and when I reboot, my system hangs saying
> > "LIL"
> > I've read something in the web as:
> > LIL (The descriptor table could not be read.)
> > LIL (This is typically caused by media failure or geometry mismatch)
> >
> > But nothing of these really helped me and that is why I'm contacting you.
> > I must say that
> > I have two SATA WD800 disks. I'm running debian with the kernel 2.4.19 and
> > LILO 22.2.
> >
> > I've made the process three times, and always the same, so I think I'm not
> > missing any
> > step...
> >
> > If you have a minute I would be grateful if you could give me an advice.
> >
> > I loof forward to hearing from you.
> >
> > Sincerely,
> >
> > Agustín Ciciliani
> >
>
>
> --
> --Luke CS Sysadmin, Montana State University-Bozeman
>
>
>
linear
boot=/dev/md1
raid-extra-boot=/dev/hda,/dev/hdc
disk=/dev/hda
bios=0x80
disk=/dev/hdc
bios=0x81
root=/dev/md2
read-only
install=/boot/boot-menu.b
map=/boot/map
delay=20
vga=normal
default=RAID
image=/boot/vmlinuz-2.4.19
label=RAID
