Package: src:linux
Version: 4.17.8-1~bpo9+1
Severity: critical
Dear Maintainer,
after switching 4.16 to 4.17 (strech-backport) my system rendered unusable,
because the encrypted disk is not unlocked any more.
The dialog is missing.
Inspecting the initramfs shows that the cryptsetup related parts are missing
for 4.17, but still in the 4.16 kernel.
I was able to mitigate the issue by use the cryptsetup packages from buster.
-- Package-specific info:
** Version:
Linux version 4.17.0-0.bpo.1-amd64 (debian-ker...@lists.debian.org) (gcc
version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 SMP Debian 4.17.8-1~bpo9+1
(2018-07-23)
** Command line:
BOOT_IMAGE=/vmlinuz-4.17.0-0.bpo.1-amd64 root=/dev/mapper/system-root ro
net.ifnames=0 quiet splash
** Not tainted
** Kernel log:
Unable to read kernel log; any relevant messages should be attached
** Model information
sys_vendor: Hewlett-Packard
product_name: HP EliteBook Revolve 810 G3
product_version: A3009FD18203
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: M86 Ver. 01.16
board_vendor: Hewlett-Packard
board_name: 22FB
board_version: KBC Version 04.27
** Loaded modules:
fuse
rfcomm
ctr
ccm
cpufreq_powersave
cpufreq_userspace
cpufreq_conservative
cmac
bnep
hid_multitouch
hid_sensor_rotation
hid_sensor_incl_3d
hid_sensor_magn_3d
hid_sensor_als
hid_sensor_accel_3d
hid_sensor_gyro_3d
hid_sensor_trigger
hid_sensor_iio_common
industrialio_triggered_buffer
btusb
btrtl
btbcm
btintel
bluetooth
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_v4l2
videobuf2_common
videodev
drbg
media
ansi_cprng
cdc_ether
ecdh_generic
qcserial
usbnet
usb_wwan
mii
usbserial
binfmt_misc
ipt_REJECT
nf_reject_ipv4
nf_log_ipv4
nf_log_common
xt_LOG
iTCO_wdt
iTCO_vendor_support
arc4
xt_limit
xt_tcpudp
xt_addrtype
nf_conntrack_ipv4
nf_defrag_ipv4
iwlmvm
intel_rapl
x86_pkg_temp_thermal
xt_conntrack
intel_powerclamp
mac80211
kvm_intel
kvm
irqbypass
intel_cstate
intel_uncore
intel_rapl_perf
snd_hda_codec_hdmi
joydev
hp_wmi
snd_hda_codec_realtek
iwlwifi
wmi_bmof
snd_hda_codec_generic
serio_raw
pcspkr
sg
snd_hda_intel
rtsx_pci_ms
cfg80211
memstick
snd_hda_codec
snd_hda_core
rfkill
tpm_infineon
snd_hwdep
snd_pcm
snd_timer
snd
mei_me
soundcore
lpc_ich
shpchp
mei
battery
tpm_tis
acpi_als
tpm_tis_core
intel_vbtn
kfifo_buf
sparse_keymap
tpm
soc_button_array
rng_core
industrialio
hp_wireless
ac
evdev
ip6table_filter
ip6_tables
nf_nat_irc
nf_conntrack_irc
nf_nat_ftp
nf_nat
nf_conntrack_ftp
nf_conntrack
crc32c_generic
iptable_filter
sunrpc
coretemp
lp
parport
loop
cdc_wdm
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
fscrypto
algif_skcipher
af_alg
raid10
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
xor
raid6_pq
libcrc32c
raid1
raid0
multipath
linear
md_mod
sha256_ssse3
dm_crypt
dm_mod
sd_mod
hid_sensor_custom
hid_sensor_hub
hid_generic
usbhid
hid
rtsx_pci_sdmmc
mmc_core
crct10dif_pclmul
crc32_pclmul
crc32c_intel
ghash_clmulni_intel
pcbc
aesni_intel
aes_x86_64
crypto_simd
cryptd
glue_helper
ahci
xhci_pci
libahci
psmouse
i915
i2c_i801
i2c_algo_bit
libata
ehci_pci
drm_kms_helper
scsi_mod
ehci_hcd
xhci_hcd
rtsx_pci
e1000e
usbcore
drm
usb_common
thermal
wmi
video
button
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Broadwell-U Host Bridge -OPI
[8086:1604] (rev 09)
Subsystem: Hewlett-Packard Company Broadwell-U Host Bridge -OPI
[103c:22fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: bdw_uncore
00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics 5500
[8086:1616] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company HD Graphics 5500 [103c:22fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at b0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 5000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:03.0 Audio device [0403]: Intel Corporation Broadwell-U Audio Controller
[8086:160c] (rev 09)
Subsystem: Hewlett-Packard Company Broadwell-U Audio Controller
[103c:22fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 52
Region 0: Memory at c1330000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.0 USB controller [0c03]: Intel Corporation Wildcat Point-LP USB xHCI
Controller [8086:9cb1] (rev 03) (prog-if 30 [XHCI])
Subsystem: Hewlett-Packard Company Wildcat Point-LP USB xHCI Controller
[103c:22fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 47
Region 0: Memory at c1320000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:16.0 Communication controller [0780]: Intel Corporation Wildcat Point-LP MEI
Controller #1 [8086:9cba] (rev 03)
Subsystem: Hewlett-Packard Company Wildcat Point-LP MEI Controller
[103c:22fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 50
Region 0: Memory at c133b000 (64-bit, non-prefetchable) [size=32]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:19.0 Ethernet controller [0200]: Intel Corporation Ethernet Connection (3)
I218-LM [8086:15a2] (rev 03)
Subsystem: Intel Corporation Ethernet Connection (3) I218-LM [8086:22fb]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 45
Region 0: Memory at c1300000 (32-bit, non-prefetchable) [disabled]
[size=128K]
Region 1: Memory at c133d000 (32-bit, non-prefetchable) [disabled]
[size=4K]
Region 2: I/O ports at 5080 [disabled] [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1b.0 Audio device [0403]: Intel Corporation Wildcat Point-LP High Definition
Audio Controller [8086:9ca0] (rev 03)
Subsystem: Hewlett-Packard Company Wildcat Point-LP High Definition
Audio Controller [103c:22fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 51
Region 0: Memory at c1334000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation Wildcat Point-LP PCI Express Root
Port #1 [8086:9c90] (rev e3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 42
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: c1200000-c12fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation Wildcat Point-LP PCI Express Root
Port #2 [8086:9c92] (rev e3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 43
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00004fff
Memory behind bridge: c1100000-c11fffff
Prefetchable memory behind bridge: 00000000ae900000-00000000aeafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation Wildcat Point-LP PCI Express Root
Port #4 [8086:9c96] (rev e3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 44
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: c1000000-c10fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB controller [0c03]: Intel Corporation Wildcat Point-LP USB EHCI
Controller [8086:9ca6] (rev 03) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Wildcat Point-LP USB EHCI Controller
[103c:22fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c1339000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge [0601]: Intel Corporation Wildcat Point-LP LPC Controller
[8086:9cc3] (rev 03)
Subsystem: Hewlett-Packard Company Wildcat Point-LP LPC Controller
[103c:22fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation Wildcat Point-LP SATA
Controller [AHCI Mode] [8086:9c83] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Wildcat Point-LP SATA Controller
[AHCI Mode] [103c:22fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 48
Region 0: I/O ports at 50a8 [size=8]
Region 1: I/O ports at 50bc [size=4]
Region 2: I/O ports at 50a0 [size=8]
Region 3: I/O ports at 50b8 [size=4]
Region 4: I/O ports at 5060 [size=32]
Region 5: Memory at c1338000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation Wildcat Point-LP SMBus Controller
[8086:9ca2] (rev 03)
Subsystem: Hewlett-Packard Company Wildcat Point-LP SMBus Controller
[103c:22fb]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at c133a000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at ef80 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5227 PCI
Express Card Reader [10ec:5227] (rev 01)
Subsystem: Hewlett-Packard Company RTS5227 PCI Express Card Reader
[103c:22fb]
Physical Slot: 1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at c1100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: rtsx_pci
Kernel modules: rtsx_pci
03:00.0 Network controller [0280]: Intel Corporation Wireless 7265 [8086:095a]
(rev 48)
Subsystem: Intel Corporation Dual Band Wireless-N 7265 [8086:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at c1000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
** USB devices:
Bus 001 Device 002: ID 8087:8001 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 006: ID 03eb:8a06 Atmel Corp.
Bus 002 Device 005: ID 05c8:0374 Cheng Uei Precision Industry Co., Ltd (Foxlink)
Bus 002 Device 004: ID 03f0:581d Hewlett-Packard
Bus 002 Device 003: ID 0483:91d1 STMicroelectronics Sensor Hub
Bus 002 Device 002: ID 8087:0a2a Intel Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
*** Reporter, please consider answering these questions, where appropriate ***
* What led up to the situation?
* What exactly did you do (or not do) that was effective (or
ineffective)?
* What was the outcome of this action?
* What outcome did you expect instead?
*** End of the template - remove these template lines ***
-- System Information:
Debian Release: 9.5
APT prefers stable-updates
APT policy: (600, 'stable-updates'), (600, 'stable'), (200, 'testing'), (101,
'unstable'), (1, 'experimental')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.17.0-0.bpo.1-amd64 (SMP w/4 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8) (ignored: LC_ALL
set to de_DE.UTF-8), LANGUAGE=de_DE.UTF-8 (charmap=UTF-8) (ignored: LC_ALL set
to de_DE.UTF-8)
Shell: /bin/sh linked to /bin/bash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.130
ii kmod 23-2
ii linux-base 4.5
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 recommends:
pn apparmor <none>
ii firmware-linux-free 3.4
ii irqbalance 1.1.0-2.3
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 suggests:
pn debian-kernel-handbook <none>
ii extlinux 3:6.03+dfsg-14.1+deb9u1
ii grub-efi-amd64 2.02~beta3-5
pn linux-doc-4.17 <none>
Versions of packages linux-image-4.17.0-0.bpo.1-amd64 is related to:
ii firmware-amd-graphics 20170823-1~bpo9+1
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 20170823-1~bpo9+1
pn firmware-libertas <none>
ii firmware-linux-nonfree 20170823-1~bpo9+1
ii firmware-misc-nonfree 20170823-1~bpo9+1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
