Package: ifenslave-2.6
Version: 1.1.0-17
Severity: important
There is a dual-port NIC Intel PRO/1000MT c PCI-X bus (on a normal PCI appear
similar problems).
Both interfaces are configured as a network card bonding:
==========================================================
files ~ # cat /etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto bond0 eth2 eth3
iface bond0 inet static
address 10.0.0.11
netmask 255.255.255.0
gateway 10.0.0.254
bond-slaves none
bond-mode balance-alb
bond-downdelay 200
bond-updelay 200
allow-hotplug eth2
iface eth2 inet manual
bond-master bond0
bond-primary eth2 eth3
allow-hotplug eth3
iface eth3 inet manual
bond-master bond0
bond-primary eth2 eth3
files ~ # cat /etc/modprobe.d/aliases-bond.conf
alias bond0 bonding
options bonding arp_interval=200 arp_ip_target=10.0.0.1,10.0.0.4
files ~ # ifconfig
bond0 Link encap:Ethernet HWaddr 00:07:e9:a5:14:f7
inet addr:10.0.0.11 Bcast:10.0.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:44564 errors:0 dropped:0 overruns:0 frame:0
TX packets:47089 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:8311464 (7.9 MiB) TX bytes:39156386 (37.3 MiB)
eth2 Link encap:Ethernet HWaddr 00:07:e9:a5:14:f7
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:31352 errors:0 dropped:0 overruns:0 frame:0
TX packets:37836 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5245222 (5.0 MiB) TX bytes:38583024 (36.7 MiB)
eth3 Link encap:Ethernet HWaddr 00:07:e9:a5:14:f6
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:13212 errors:0 dropped:0 overruns:0 frame:0
TX packets:9253 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3066242 (2.9 MiB) TX bytes:573362 (559.9 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:31 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2568 (2.5 KiB) TX bytes:2568 (2.5 KiB)
===============================================================
When I disconnect the wire from one of the interfaces to the console messages
are displayed:
http://www.k-max.name/wp-content/uploads/2011/08/errors.jpg
In the log file / var / log / messages a lot of these messages:
=================================================================
Aug 5 18:40:25 files kernel: [ 9.912383] e1000: eth2 NIC Link is Up 1000
Mbps Full Duplex, Flow Control: RX
Aug 5 18:40:25 files kernel: [ 9.925118] bonding: bond0: Warning: failed to
get speed and duplex from eth3, assumed to be 100Mb/sec and Full.
Aug 5 18:40:25 files kernel: [ 9.925149] bonding: bond0: enslaving eth3 as
an active interface with an up link.
Aug 5 18:40:25 files kernel: [ 9.925164] bonding: bond0: Setting eth2 as
primary slave.
Aug 5 18:40:25 files kernel: [ 9.930836] bonding: bond0: Setting eth2 as
primary slave.
Aug 5 18:40:25 files kernel: [ 9.944397] e1000: eth3 NIC Link is Up 1000
Mbps Full Duplex, Flow Control: RX
Aug 5 18:40:25 files kernel: [ 11.180611] lp0: using parport0
(interrupt-driven).
Aug 5 18:40:25 files kernel: [ 11.197377] ppdev: user-space parallel port
driver
Aug 5 18:42:57 files kernel: [ 162.492113] e1000: eth2 NIC Link is Down
Aug 5 18:43:01 files kernel: [ 167.300017] bonding: bond0: interface eth2 is
now down.
Aug 5 18:43:01 files kernel: [ 167.300030] bonding: bond0: making interface
eth3 the new active one.
Aug 5 18:43:01 files kernel: [ 167.300253] Pid: 848, comm: bond0 Not tainted
2.6.32-5-686 #1
Aug 5 18:43:01 files kernel: [ 167.300258] Call Trace:
Aug 5 18:43:01 files kernel: [ 167.300276] [<f8234266>] ?
bond_alb_handle_active_change+0xec/0x158 [bonding]
Aug 5 18:43:01 files kernel: [ 167.300286] [<f822f23e>] ?
bond_change_active_slave+0x1dc/0x42b [bonding]
Aug 5 18:43:01 files kernel: [ 167.300299] [<c126d49e>] ?
schedule+0x78f/0x7dc
Aug 5 18:43:01 files kernel: [ 167.300308] [<f822f7a8>] ?
bond_select_active_slave+0x86/0xb4 [bonding]
Aug 5 18:43:01 files kernel: [ 167.300317] [<f822fe10>] ?
bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
Aug 5 18:43:01 files kernel: [ 167.300327] [<c10412f7>] ?
worker_thread+0x141/0x1bd
Aug 5 18:43:01 files kernel: [ 167.300336] [<f822fc8a>] ?
bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
Aug 5 18:43:01 files kernel: [ 167.300345] [<c104403a>] ?
autoremove_wake_function+0x0/0x2d
Aug 5 18:43:01 files kernel: [ 167.300351] [<c10411b6>] ?
worker_thread+0x0/0x1bd
Aug 5 18:43:01 files kernel: [ 167.300358] [<c1043e08>] ? kthread+0x61/0x66
Aug 5 18:43:01 files kernel: [ 167.300365] [<c1043da7>] ? kthread+0x0/0x66
Aug 5 18:43:01 files kernel: [ 167.300374] [<c1003d47>] ?
kernel_thread_helper+0x7/0x10
Aug 5 18:43:01 files kernel: [ 167.300475] Pid: 848, comm: bond0 Not tainted
2.6.32-5-686 #1
Aug 5 18:43:01 files kernel: [ 167.300932] Call Trace:
Aug 5 18:43:01 files kernel: [ 167.300941] [<c121836f>] ?
inetdev_event+0x40/0x3c3
Aug 5 18:43:01 files kernel: [ 167.300950] [<c11f39e6>] ?
rt_cache_flush+0x13f/0x161
Aug 5 18:43:01 files kernel: [ 167.300957] [<c12702c8>] ?
notifier_call_chain+0x2a/0x47
Aug 5 18:43:01 files kernel: [ 167.300964] [<c10476ce>] ?
raw_notifier_call_chain+0x9/0xc
Aug 5 18:43:01 files kernel: [ 167.300971] [<c11da5ea>] ?
dev_set_mac_address+0x4d/0x52
Aug 5 18:43:01 files kernel: [ 167.300981] [<f8233933>] ?
alb_set_slave_mac_addr+0x68/0xa2 [bonding]
Aug 5 18:43:01 files kernel: [ 167.300991] [<f82339a7>] ?
alb_swap_mac_addr+0x3a/0x4f [bonding]
Aug 5 18:43:01 files kernel: [ 167.301000] [<f823427c>] ?
bond_alb_handle_active_change+0x102/0x158 [bonding]
Aug 5 18:43:01 files kernel: [ 167.301009] [<f822f23e>] ?
bond_change_active_slave+0x1dc/0x42b [bonding]
Aug 5 18:43:01 files kernel: [ 167.301017] [<c126d49e>] ?
schedule+0x78f/0x7dc
Aug 5 18:43:01 files kernel: [ 167.301025] [<f822f7a8>] ?
bond_select_active_slave+0x86/0xb4 [bonding]
Aug 5 18:43:01 files kernel: [ 167.301034] [<f822fe10>] ?
bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
Aug 5 18:43:01 files kernel: [ 167.301041] [<c10412f7>] ?
worker_thread+0x141/0x1bd
Aug 5 18:43:01 files kernel: [ 167.301049] [<f822fc8a>] ?
bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
Aug 5 18:43:01 files kernel: [ 167.301056] [<c104403a>] ?
autoremove_wake_function+0x0/0x2d
Aug 5 18:43:01 files kernel: [ 167.301062] [<c10411b6>] ?
worker_thread+0x0/0x1bd
Aug 5 18:43:01 files kernel: [ 167.301068] [<c1043e08>] ? kthread+0x61/0x66
Aug 5 18:43:01 files kernel: [ 167.301074] [<c1043da7>] ? kthread+0x0/0x66
Aug 5 18:43:01 files kernel: [ 167.301081] [<c1003d47>] ?
kernel_thread_helper+0x7/0x10
.......
Aug 5 18:43:01 files kernel: [ 167.302048] Pid: 848, comm: bond0 Not tainted
2.6.32-5-686 #1
Aug 5 18:43:01 files kernel: [ 167.302052] Call Trace:
Aug 5 18:43:01 files kernel: [ 167.302059] [<c11d8778>] ?
__dev_set_promiscuity+0x2f/0x128
Aug 5 18:43:01 files kernel: [ 167.302066] [<c11d8c47>] ?
dev_set_promiscuity+0x10/0x2e
Aug 5 18:43:01 files kernel: [ 167.302075] [<f8233dcd>] ?
rlb_teach_disabled_mac_on_primary+0x22/0x44 [bonding]
Aug 5 18:43:01 files kernel: [ 167.302084] [<f8234288>] ?
bond_alb_handle_active_change+0x10e/0x158 [bonding]
Aug 5 18:43:01 files kernel: [ 167.302093] [<f822f23e>] ?
bond_change_active_slave+0x1dc/0x42b [bonding]
Aug 5 18:43:01 files kernel: [ 167.302101] [<c126d49e>] ?
schedule+0x78f/0x7dc
Aug 5 18:43:01 files kernel: [ 167.302109] [<f822f7a8>] ?
bond_select_active_slave+0x86/0xb4 [bonding]
Aug 5 18:43:01 files kernel: [ 167.302118] [<f822fe10>] ?
bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
Aug 5 18:43:01 files kernel: [ 167.302125] [<c10412f7>] ?
worker_thread+0x141/0x1bd
Aug 5 18:43:01 files kernel: [ 167.302134] [<f822fc8a>] ?
bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
Aug 5 18:43:01 files kernel: [ 167.302141] [<c104403a>] ?
autoremove_wake_function+0x0/0x2d
Aug 5 18:43:01 files kernel: [ 167.302147] [<c10411b6>] ?
worker_thread+0x0/0x1bd
Aug 5 18:43:01 files kernel: [ 167.302153] [<c1043e08>] ? kthread+0x61/0x66
Aug 5 18:43:01 files kernel: [ 167.302159] [<c1043da7>] ? kthread+0x0/0x66
Aug 5 18:43:01 files kernel: [ 167.302165] [<c1003d47>] ?
kernel_thread_helper+0x7/0x10
Aug 5 18:43:01 files kernel: [ 167.302170] device eth3 entered promiscuous
mode
Aug 5 18:43:02 files kernel: [ 168.024374] e1000: eth2 NIC Link is Up 1000
Mbps Full Duplex, Flow Control: RX
Aug 5 18:43:11 files kernel: [ 177.296030] device eth3 left promiscuous mode
Aug 5 18:43:33 files kernel: [ 199.300018] bonding: bond0: interface eth2 is
now up
Aug 5 18:43:45 files kernel: [ 211.140114] e1000: eth2 NIC Link is Down
Aug 5 18:43:49 files kernel: [ 215.300017] bonding: bond0: interface eth2 is
now down.
Aug 5 18:43:51 files kernel: [ 217.332372] e1000: eth2 NIC Link is Up 1000
Mbps Full Duplex, Flow Control: RX
Aug 5 18:44:00 files kernel: [ 226.364113] e1000: eth3 NIC Link is Down
Aug 5 18:44:05 files kernel: [ 231.300021] bonding: bond0: interface eth3 is
now down.
Aug 5 18:44:05 files kernel: [ 231.300088] bonding: bond0: now running
without any active interface !
Aug 5 18:44:07 files kernel: [ 232.980372] e1000: eth3 NIC Link is Up 1000
Mbps Full Duplex, Flow Control: RX
Aug 5 18:44:23 files kernel: [ 249.300014] bonding: bond0: link status
definitely up for interface eth2,
Aug 5 18:44:23 files kernel: [ 249.300034] bonding: bond0: making interface
eth2 the new active one.
Aug 5 18:44:23 files kernel: [ 249.300225] Pid: 848, comm: bond0 Not tainted
2.6.32-5-686 #1
Aug 5 18:44:23 files kernel: [ 249.300230] Call Trace:
Aug 5 18:44:23 files kernel: [ 249.300248] [<f8234266>] ?
bond_alb_handle_active_change+0xec/0x158 [bonding]
Aug 5 18:44:23 files kernel: [ 249.300258] [<f822f23e>] ?
bond_change_active_slave+0x1dc/0x42b [bonding]
Aug 5 18:44:23 files kernel: [ 249.300270] [<c126d49e>] ?
schedule+0x78f/0x7dc
Aug 5 18:44:23 files kernel: [ 249.300279] [<f822f7a8>] ?
bond_select_active_slave+0x86/0xb4 [bonding]
Aug 5 18:44:23 files kernel: [ 249.300288] [<f822fe10>] ?
bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
Aug 5 18:44:23 files kernel: [ 249.300299] [<c10412f7>] ?
worker_thread+0x141/0x1bd
Aug 5 18:44:23 files kernel: [ 249.300307] [<f822fc8a>] ?
bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
Aug 5 18:44:23 files kernel: [ 249.300316] [<c104403a>] ?
autoremove_wake_function+0x0/0x2d
-- System Information:
Debian Release: 6.0.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages ifenslave-2.6 depends on:
ii iproute 20100519-3 networking and traffic control too
ii libc6 2.11.2-10 Embedded GNU C Library: Shared lib
Versions of packages ifenslave-2.6 recommends:
ii net-tools 1.60-23 The NET-3 networking toolkit
ifenslave-2.6 suggests no packages.
-- no debconf information
--
To UNSUBSCRIBE, email to [email protected]
with a subject of "unsubscribe". Trouble? Contact [email protected]
