Subject: linux-image-2.6.26-1-amd64: the SATA CDROM isn't detected
Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-4
Severity: important
*** Please type your report below this line ***
I get errors shown in the kernel log and can't access the CD-ROM.
I think this not a Debian specific problem because I have this error
with a "stock" 2.6.26.3 kernel (from ftp.kernel.org) too. But I hadn't
this error with a 2.6.25 kernel.
Could it be a timing problem in sata_nv?
My MoBo is an Asus M2N32 WS Professional with these storage controlers
(short form, long form see below):
H/W path Device Class Description
===================================================
/0/c storage MCP55 IDE
/0/d scsi0 storage MCP55 SATA Controller
/0/d.1 storage MCP55 SATA Controller
/0/d.2 storage MCP55 SATA Controller
/0/16/0 storage 88SE6145 SATA II PCI-E controller
-- Package-specific info:
** Version:
Linux version 2.6.26-1-amd64 (Debian 2.6.26-4) ([EMAIL PROTECTED]) (gcc version
4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Thu Aug 28 11:13:42 UTC
2008
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.26-1-amd64
root=UUID=7e37e815-ca3c-4ce5-9987-88eef03937b4 ro
** Not tainted
** Kernel log:
[ 1.598100] sata_nv 0000:00:0d.0: version 3.5
[ 1.598100] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
[ 1.598100] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APSI] -> GSI 21
(level, low) -> IRQ 21
[ 1.598100] sata_nv 0000:00:0d.0: Using SWNCQ mode
[ 1.598100] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 1.598100] scsi0 : sata_nv
[ 1.598100] scsi1 : sata_nv
[ 1.598100] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xe000 irq 21
[ 1.598100] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xe008 irq 21
[ 1.924441] usb 2-2: new low speed USB device using ohci_hcd and address 2
[ 2.093397] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.101336] ata1.00: ATA-7: SAMSUNG HD103UJ, 1AA01112, max UDMA7
[ 2.101336] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 2.101336] ata1.00: Drive reports diagnostics failure. This may indicate a
drive
[ 2.101336] ata1.00: fault or invalid emulation. Contact drive vendor for
information.
[ 2.118606] ata1.00: configured for UDMA/133
[ 2.154069] usb 2-2: configuration #1 chosen from 1 choice
[ 2.154069] usb 2-2: New USB device found, idVendor=046d, idProduct=c501
[ 2.154069] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.154069] usb 2-2: Product: USB Receiver
[ 2.154069] usb 2-2: Manufacturer: Logitech
[ 9.729091] ata2: link is slow to respond, please be patient (ready=-19)
[ 16.654084] ata2: SRST failed (errno=-16)
[ 24.158262] ata2: link is slow to respond, please be patient (ready=-19)
[ 31.138728] ata2: SRST failed (errno=-16)
[ 38.146731] ata2: link is slow to respond, please be patient (ready=-19)
[ 79.491224] ata2: SRST failed (errno=-16)
[ 79.491299] ata2: limiting SATA link speed to 1.5 Gbps
[ 86.927693] ata2: SRST failed (errno=-16)
[ 86.927766] ata2: reset failed, giving up
** Loaded modules:
Module Size Used by
ext2 66448 0
usb_storage 94400 1
wacom 22144 0
binfmt_misc 13580 1
kvm_amd 29452 0
kvm 127464 1 kvm_amd
ppdev 11656 0
lp 14724 0
autofs4 24200 1
video 24084 0
output 7808 1 video
ac 9352 0
battery 16904 0
cpufreq_stats 9120 0
cpufreq_userspace 8452 0
cpufreq_powersave 6400 0
cpufreq_ondemand 11792 0
cpufreq_conservative 11784 0
freq_table 9344 2 cpufreq_stats,cpufreq_ondemand
nfsd 248360 17
auth_rpcgss 47520 1 nfsd
exportfs 8704 1 nfsd
nfs 251696 1
lockd 68560 2 nfsd,nfs
nfs_acl 7552 2 nfsd,nfs
sunrpc 197608 16 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
ipv6 288200 49
fuse 53184 1
dm_multipath 21392 0
loop 19468 0
snd_hda_intel 434776 1
snd_pcsp 14588 0
parport_pc 31016 1
parport 41776 3 ppdev,lp,parport_pc
snd_pcm_oss 41760 0
snd_mixer_oss 18816 1 snd_pcm_oss
snd_pcm 81800 3 snd_hda_intel,snd_pcsp,snd_pcm_oss
snd_timer 25744 1 snd_pcm
k8temp 9216 0
snd 63688 8
snd_hda_intel,snd_pcsp,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
shpchp 34080 0
pci_hotplug 32056 1 shpchp
i2c_nforce2 10752 0
soundcore 12064 1 snd
snd_page_alloc 13072 2 snd_hda_intel,snd_pcm
i2c_core 27936 1 i2c_nforce2
button 11680 0
evdev 14208 3
ext3 124688 11
jbd 51240 1 ext3
mbcache 12804 2 ext2,ext3
dm_mirror 20608 0
dm_log 13956 1 dm_mirror
dm_snapshot 19400 0
dm_mod 58864 15 dm_multipath,dm_mirror,dm_log,dm_snapshot
raid10 23680 0
raid456 125984 0
async_xor 8448 1 raid456
async_memcpy 6912 1 raid456
async_tx 11764 3 raid456,async_xor,async_memcpy
xor 9744 2 raid456,async_xor
raid1 24192 0
raid0 10624 0
multipath 11392 0
linear 8960 0
md_mod 80164 6 raid10,raid456,raid1,raid0,multipath,linear
sd_mod 29376 10
pata_marvell 8832 0
amd74xx 13448 0 [permanent]
usbhid 45792 0
hid 41792 1 usbhid
ff_memless 9224 1 usbhid
ide_pci_generic 9220 0 [permanent]
ide_core 128284 2 amd74xx,ide_pci_generic
floppy 61672 0
ahci 32520 0
ohci1394 32564 0
sata_nv 27528 9
ata_generic 10116 0
ieee1394 93816 1 ohci1394
libata 165472 4 pata_marvell,ahci,sata_nv,ata_generic
forcedeth 54032 0
scsi_mod 160760 3 usb_storage,sd_mod,libata
dock 14112 1 libata
ohci_hcd 25092 0
ehci_hcd 36108 0
thermal 22688 0
processor 42304 1 thermal
fan 9352 0
thermal_sys 17728 4 video,thermal,processor,fan
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02f4] (rev
a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:00.1 RAM memory [0500]: nVidia Corporation C51 Memory Controller 0
[10de:02fa] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR+ <PERR- INTx-
00:00.2 RAM memory [0500]: nVidia Corporation C51 Memory Controller 1
[10de:02fe] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory [0500]: nVidia Corporation C51 Memory Controller 5
[10de:02f8] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.4 RAM memory [0500]: nVidia Corporation C51 Memory Controller 4
[10de:02f9] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.5 RAM memory [0500]: nVidia Corporation C51 Host Bridge [10de:02ff] (rev
a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:00.6 RAM memory [0500]: nVidia Corporation C51 Memory Controller 3
[10de:027f] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:00.7 RAM memory [0500]: nVidia Corporation C51 Memory Controller 2
[10de:027e] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fc]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:04.0 PCI bridge [0604]: nVidia Corporation C51 PCI Express Bridge
[10de:02fb] (rev a1)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:08.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller
[10de:0369] (rev a1)
Subsystem: nVidia Corporation Device [10de:cb84]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:09.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge [10de:0360] (rev
a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:09.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 5
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 1c40 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:0a.0 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036c] (rev a1) (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0a.1 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036d] (rev a2) (prog-if 20)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:0c.0 IDE interface [0101]: nVidia Corporation MCP55 IDE [10de:036e] (rev a1)
(prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f400 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
Kernel modules: ata_generic, amd74xx, ide-pci-generic
00:0d.0 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at e000 [size=16]
Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: ata_generic, sata_nv, ide-pci-generic
00:0d.1 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at cc00 [size=16]
Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: ata_generic, sata_nv, ide-pci-generic
00:0d.2 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller
[10de:037f] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 23
Region 0: I/O ports at c800 [size=8]
Region 1: I/O ports at c400 [size=4]
Region 2: I/O ports at c000 [size=8]
Region 3: I/O ports at bc00 [size=4]
Region 4: I/O ports at b800 [size=16]
Region 5: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: ata_generic, sata_nv, ide-pci-generic
00:0e.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge [10de:0370] (rev
a2) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: fdf00000-fdffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn+
Capabilities: <access denied>
00:0e.1 Audio device [0403]: nVidia Corporation MCP55 High Definition Audio
[10de:0371] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81f6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at fe020000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:10.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 1272
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b400 [size=8]
Region 2: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at fe028000 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:11.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:81fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 1271
Region 0: Memory at fe027000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b000 [size=8]
Region 2: Memory at fe026000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at fe025000 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:12.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0376] (rev a2)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=05, sec-latency=0
Memory behind bridge: fde00000-fdefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:14.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0374] (rev a2)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:15.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0378] (rev a2)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:16.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0375] (rev a2)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 00009000-0000afff
Memory behind bridge: fdd00000-fddfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:17.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0377] (rev a2)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp
02:0b.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:815b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fdff8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
03:00.0 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express - PCI/PCI-X
Bridge [1033:0125] (rev 06)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=03, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
03:00.1 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express - PCI/PCI-X
Bridge [1033:0125] (rev 06)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Region 0: Memory at fdeff000 (64-bit, non-prefetchable) [size=128]
Bus: primary=03, secondary=05, subordinate=05, sec-latency=32
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: shpchp
Kernel modules: shpchp
08:00.0 RAID bus controller [0104]: Marvell Technology Group Ltd. 88SE6145 SATA
II PCI-E controller [11ab:6145] (rev a1) (prog-if 8f)
Subsystem: ASUSTeK Computer Inc. Device [1043:8220]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at a800 [size=4]
Region 2: I/O ports at a400 [size=8]
Region 3: I/O ports at a000 [size=4]
Region 4: I/O ports at 9c00 [size=16]
Region 5: Memory at fddff000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at fdd80000 [disabled] [size=256K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: pata_marvell, ahci
09:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon HD 3850
[1002:9505]
Subsystem: ATI Technologies Inc Device [1002:e630]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fdce0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 8c00 [size=256]
Expansion ROM at fdcc0000 [disabled] [size=128K]
Capabilities: <access denied>
09:00.1 Audio device [0403]: ATI Technologies Inc Radeon HD 3870 Audio device
[1002:aa18]
Subsystem: ATI Technologies Inc Radeon HD 3870 Audio device [1002:aa18]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 16
Region 0: Memory at fdcfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92g tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii grub-pc [grub] 1.96+20080724-9 GRand Unified Bootloader, version
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-amd64/postinst/create-kimage-link-2.6.26-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-amd64/postinst/old-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/bootloader-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/initrd-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-system-map-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-initrd-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/preinst/overwriting-modules-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/elilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-install-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/lilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/prerm/removing-running-kernel-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/prerm/would-invalidate-boot-loader-2.6.26-1-amd64:
true
linux-image-2.6.26-1-amd64/postinst/bootloader-test-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-overwrite-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-dir-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-amd64/preinst/failed-to-move-modules-2.6.26-1-amd64:
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
