Package: installation-reports Possibly a followup to #253789, sorry for the long delay, I had to fix the board.
Debian-installer-version: Sat, 12 Mar 21:10 EST 2005 http://people.debian.org/~kmuto/d-i/images/daily/netwinder/netboot/boot.img uname -a: Linux barad-dur 2.4.27-netwinder #1 Tue Feb 22 15:24:37 GMT 2005 armv4l GNU/Linux Date: Sat Mar 12 22:55:51 EST 2005 Method: Network booted from local DHCP server. Serial console. Machine: Rebel Netwinder Processor: [EMAIL PROTECTED]:~% cat /proc/cpuinfo Processor : StrongARM-110 rev 4 (v4l) BogoMIPS : 185.95 Features : swp half 26bit fastmult Hardware : Rebel-NetWinder Revision : 58ff Serial : 0000000000001e0e Memory: 64MB Root Device: 2.2GB IDE Root Size/partition table: Disk /dev/hda: 2167 MB, 2167603200 bytes 255 heads, 63 sectors/track, 263 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 * 1 11 88326 83 Linux /boot /dev/hda2 12 25 112455 83 Linux / /dev/hda3 26 263 1911735 5 Extended /dev/hda4 1 1 0 0 Empty Partition 4 has different physical/logical beginnings (non-Linux?): phys=(0, 0, 0) logical=(0, 0, 1) Partition 4 has different physical/logical endings: phys=(0, 0, 0) logical=(267349, 89, 4) Partition 4 does not end on cylinder boundary. /dev/hda5 26 128 827316 83 Linux /usr /dev/hda6 129 160 257008+ 83 Linux /var /dev/hda7 161 175 120456 82 Linux swap /dev/hda8 176 182 56196 83 Linux /tmp /dev/hda9 183 263 650601 83 Linux /home Output of lspci and lspci -n: [EMAIL PROTECTED]:~% lspci 0000:00:00.0 Co-processor: Digital Equipment Corporation StrongARM DC21285 (rev 03) 0000:00:09.0 VGA compatible controller: Intergraphics Systems CyberPro 2000A (rev 01) 0000:00:0a.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41) 0000:00:0c.0 ISA bridge: Symphony Labs W83C553 (rev 10) 0000:00:0c.1 IDE interface: Symphony Labs SL82c105 (rev 05) 0000:00:0d.0 Ethernet controller: Winbond Electronics Corp W89C940F [EMAIL PROTECTED]:~% lspci -n 0000:00:00.0 0b40: 1011:1065 (rev 03) 0000:00:09.0 0300: 10ea:2010 (rev 01) 0000:00:0a.0 0200: 1011:0019 (rev 41) 0000:00:0c.0 0601: 10ad:0565 (rev 10) 0000:00:0c.1 0101: 10ad:0105 (rev 05) 0000:00:0d.0 0200: 1050:5a5a Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] (see below) Create file systems: [O] Mount partitions: [O] Install base system: [O] (network failed once, and retried) Install boot loader: [O] Reboot: [O] Comments/Problems: Most of this will, I guess, apply to sarge+1... I guess detect cd was fine, since it detected that I don't have one. Chose "multiuser system" and it partitioned things well. /boot was correctly ext2r0, excellent! Was necessary to: setenv cmdappend console=ttyS0,115200,8n1 setenv rootdev /dev/ram to get a serial console, and get the initrd going. Very awesome that the NeTTROM settings are spewed at the end, very very helpful! Seemed to "hang" a bit at "Configuring the base system" before the "Debian Configuration" menus, some feedback would be nice, as these are very slow machines. Maybe a whirlygig would be appropriate... Thanks! Kyle -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
