Package: lkcdutils
Version: 6.1.0
Hi Micah,
Thanks for early reply, Yes, i m using kernel 2.4.26.
I specified dump flags to 0, but lkcd_config failed as below
# /etc/init.d/lkcdutils
Configuring system for crash dumps...
dump flags not specified
/sbin/lkcd_config failed!
Activating swap parition
btw, #lkcd on irc.freenode.net redirects to http://svn-meta.freenode.net/
where
I did not find lkcd.
My earlier mail, after system reboots with sysrq, /etc/init.d/lkcdutils
wont
save dump in /var/log/dump/ , /var/log/dump appears to be empty.
Please help or any pointers.
-Regards
Kotrappa.
>
>
> ----- Original Message -----
> From: "Micah Anderson" <[EMAIL PROTECTED]>
> To: "Kotrappa" <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>
> Sent: Saturday, February 26, 2005 1:27 AM
> Subject: Re: Bug#296857: lkcd save command wont save dump
>
>
> > Hi,
> >
> > I notice that you are using 2.4.26 with lkcd. It is not noted
> > anywhere, but you should change your DUMP_FLAGS in /etc/lkcdutils/dump
> > to be:
> >
> > DUMP_FLAGS="0"
> >
> > Then run /etc/init.d/lkcdutils to re-load the config. Then simulate a
> > crash with the sysrq (note: this will cause your system to reboot,
> > when it did not before!), after the system reboots, look in
> > /var/log/dump to see if your dump was saved. It should be saved on boot.
> >
> > I've noted this in the README.Debian for the next upload.
> >
> > Also, you can join #lkcd on irc.freenode.net if you need help walking
> > through the procedure.
> >
> > Micah
> >
> > On Fri, 25 Feb 2005, Kotrappa wrote:
> >
> > > Package: lkcdutils
> > > Version: 6.1.0
> > > Hi,
> > >
> > > I used magic sysrq key to produce crash on the system, I could see
> dump
> > > saving into swap partition.
> > > but could not recover dump by lkcd save command.
> > > Please help!.
> > >
> > >
> > > # /sbin/lkcd save
> > > lcrash 0.10.2 (xlcrash) build at Feb 26 2005 00:09:04
> > > Lcrash is free software. It is covered by the GNU General Public
> License.
> > > You are welcome to change it and/or distribute copies of it under
> certain
> > > conditions. Type "help -C" to see the conditions. Absolutely no
> warranty
> > > is given for Lcrash. Type "help -W" for warranty details.
> > >
> > > Error: could not save crash dump: lcrash returned with 1. Maybe
there
> was
> > > no dump?
> > > Reconfiguring LKCD....
> > >
> > > Dump configuration
> > > # cat /proc/sys/dump/*
> > > 2
> > > ide1(22,3)
> > > 0x80000000
> > > 8
> > > DUMP_ACTIVE="1"
> > > DUMPDEV="/dev/vmdump"
> > > DUMP_ON_SWAP="1"
> > > DUMPDIR="/var/log/dump"
> > > DUMP_FLAGS="0x80000000"
> > >
> > >
> > > I am using
> > > # cat /proc/version
> > > Linux version 2.4.26-sudf-n-lkcd (gcc version 2.95.4 20011002
> (Debian
> > > prerelease)) #6 Fri Feb 25 21:03:04 JST 2005
> > > Kernel patch 2.4.26.
> > >
> > >
> > > -regards
> > > Kotrappa
> > >
> > > ----- Original Message -----
> > > From: [1]Kotrappa
> > > To: [EMAIL PROTECTED]
> > > Sent: Friday, February 25, 2005 4:17 PM
> > > Subject: lkcd save command wont save dump
> > >
> > >
> > > References
> > >
> > > Visible links
> > > 1. [EMAIL PROTECTED]
> > > mailto:[EMAIL PROTECTED]
> > > 2. [EMAIL PROTECTED]
> > > mailto:[EMAIL PROTECTED]
> >
>
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
