Package: shairport-sync Version: 3.2.2-1+b2 Severity: important Dear Maintainer,
shairport-sync 3.2.2 fails to start with systemd as documented at https://github.com/mikebrady/shairport-sync/issues/829. This has been fixed with https://github.com/mikebrady/shairport-sync/pull/879 but the package needs to be updated. Thank you -- System Information: Distributor ID: Raspbian Description: Raspbian GNU/Linux 10 (buster) Release: 10 Codename: buster Architecture: armv7l Kernel: Linux 5.4.51-v7l+ (SMP w/4 CPU cores) Kernel taint flags: TAINT_CRAP Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8), LANGUAGE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages shairport-sync depends on: ii adduser 3.118 ii avahi-daemon 0.7-4+b1 ii libasound2 1.1.8-1+rpt1 ii libavahi-client3 0.7-4+b1 ii libavahi-common3 0.7-4+b1 ii libc6 2.28-10+rpi1 ii libconfig9 1.5-0.4 ii libdaemon0 0.14-7 ii libgcc1 1:8.3.0-6+rpi1 ii libpopt0 1.16-12 ii libpulse0 12.2-4+deb10u1 ii libsndfile1 1.0.28-6 ii libsoxr0 0.1.2-3 ii libssl1.1 1.1.1d-0+deb10u3+rpt1 ii libstdc++6 8.3.0-6+rpi1 shairport-sync recommends no packages. shairport-sync suggests no packages. -- Configuration Files: /etc/shairport-sync.conf changed: // Sample Configuration File for Shairport Sync // Commented out settings are generally the defaults, except where noted. // General Settings general = { name = "HomeAudio %H"; // This means "Hostname" -- see below. This is the name the service will advertise to iTunes. // The default is "Hostname" -- i.e. the machine's hostname with the first letter capitalised (ASCII only.) // You can use the following substitutions: // %h for the hostname, // %H for the Hostname (i.e. with first letter capitalised (ASCII only)), // %v for the version number, e.g. 3.0 and // %V for the full version string, e.g. 3.0-OpenSSL-Avahi-ALSA-soxr-metadata-sysconfdir:/etc // Overall length can not exceed 50 characters. Example: "Shairport Sync %v on %H". // password = "secret"; // leave this commented out if you don't want to require a password // interpolation = "basic"; // aka "stuffing". Default is "basic", alternative is "soxr". Use "soxr" only if you have a reasonably fast processor. // output_backend = "alsa"; // Run "shairport-sync -h" to get a list of all output_backends, e.g. "alsa", "pipe", "stdout". The default is the first one. // mdns_backend = "avahi"; // Run "shairport-sync -h" to get a list of all mdns_backends. The default is the first one. // port = 5000; // Listen for service requests on this port // udp_port_base = 6001; // start allocating UDP ports from this port number when needed // udp_port_range = 100; // look for free ports in this number of places, starting at the UDP port base. Allow at least 10, though only three are needed in a steady state. // drift_tolerance_in_seconds = 0.002; // allow a timing error of this number of seconds of drift away from exact synchronisation before attempting to correct it // resync_threshold_in_seconds = 0.050; // a synchronisation error greater than this number of seconds will cause resynchronisation; 0 disables it // ignore_volume_control = "no"; // set this to "yes" if you want the volume to be at 100% no matter what the source's volume control is set to. // volume_range_db = 60 ; // use this advanced setting to set the range, in dB, you want between the maximum volume and the minimum volume. Range is 30 to 150 dB. Leave it commented out to use mixer's native range. // volume_max_db = 0.0 ; // use this advanced setting, which must have a decimal point in it, to set the maximum volume, in dB, you wish to use. // The setting is for the hardware mixer, if chosen, or the software mixer otherwise. The value must be in the mixer's range (0.0 to -96.2 for the software mixer). // Leave it commented out to use mixer's maximum volume. // volume_control_profile = "standard" ; // use this advanced setting to specify how the airplay volume is transferred to the mixer volume. // "standard" makes the volume change more quickly at lower volumes and slower at higher volumes. // "flat" makes the volume change at the same rate at all volumes. // run_this_when_volume_is_set = "/full/path/to/application/and/args"; // Run the specified application whenever the volume control is set or changed. // The desired AirPlay volume is appended to the end of the command line – leave a space if you want it treated as an extra argument. // AirPlay volume goes from 0 to -30 and -144 means "mute". // regtype = "_raop._tcp"; // Use this advanced setting to set the service type and transport to be advertised by Zeroconf/Bonjour. Default is "_raop._tcp". // playback_mode = "stereo"; // This can be "stereo", "mono", "reverse stereo", "both left" or "both right". Default is "stereo". // alac_decoder = "hammerton"; // This can be "hammerton" or "apple". This advanced setting allows you to choose // the original Shairport decoder by David Hammerton or the Apple Lossless Audio Codec (ALAC) decoder written by Apple. // interface = "name"; // Use this advanced setting to specify the interface on which Shairport Sync should provide its service. Leave it commented out to get the default, which is to select the interface(s) automatically. // audio_backend_latency_offset_in_seconds = 0.0; // Set this offset to compensate for a fixed delay in the audio back end. E.g. if the output device delays by 100 ms, set this to -0.1. // audio_backend_buffer_desired_length_in_seconds = 0.15; // If set too small, buffer underflow occurs on low-powered machines. Too long and the response time to volume changes becomes annoying. Default is 0.15 seconds in the alsa backend, 0.35 seconds in the pa backend and 1.0 seconds otherwise. // audio_backend_silent_lead_in_time = 2.0; // This optional advanced setting, from 0.0 and 4.0 seconds, sets the length of the period of silence that precedes the start of the audio. The default is the latency, usually 2.0 seconds. Values greater than the latency are ignored. Values that are too low will affect initial synchronisation. // dbus_service_bus = "system"; // The Shairport Sync dbus interface, if selected at compilation, will appear // as "org.gnome.ShairportSync" on the whichever bus you specify here: "system" (default) or "session". // mpris_service_bus = "system"; // The Shairport Sync mpris interface, if selected at compilation, will appear // as "org.gnome.ShairportSync" on the whichever bus you specify here: "system" (default) or "session". }; // Advanced parameters for controlling how Shairport Sync runs a play session sessioncontrol = { // run_this_before_play_begins = "/full/path/to/application and args"; // make sure the application has executable permission. If it's a script, include the shebang (#!/bin/...) on the first line // run_this_after_play_ends = "/full/path/to/application and args"; // make sure the application has executable permission. If it's a script, include the shebang (#!/bin/...) on the first line // wait_for_completion = "no"; // set to "yes" to get Shairport Sync to wait until the "run_this..." applications have terminated before continuing // allow_session_interruption = "no"; // set to "yes" to allow another device to interrupt Shairport Sync while it's playing from an existing audio source // session_timeout = 120; // wait for this number of seconds after a source disappears before terminating the session and becoming available again. }; // Back End Settings // These are parameters for the "alsa" audio back end. alsa = { // output_device = "default"; // the name of the alsa output device. Use "alsamixer" or "aplay" to find out the names of devices, mixers, etc. // mixer_control_name = "PCM"; // the name of the mixer to use to adjust output volume. If not specified, volume in adjusted in software. // mixer_device = "default"; // the mixer_device default is whatever the output_device is. Normally you wouldn't have to use this. // output_rate = 44100; // can be 44100, 88200, 176400 or 352800, but the device must have the capability. // output_format = "S16"; // can be "U8", "S8", "S16", "S24", "S24_3LE", "S24_3BE" or "S32", but the device must have the capability. Except where stated using (*LE or *BE), endianness matches that of the processor. // disable_synchronization = "no"; // Set to "yes" to disable synchronization. Default is "no". // period_size = <number>; // Use this optional advanced setting to set the alsa period size near to this value // buffer_size = <number>; // Use this optional advanced setting to set the alsa buffer size near to this value // use_mmap_if_available = "yes"; // Use this optional advanced setting to control whether MMAP-based output is used to communicate with the DAC. Default is "yes" // use_hardware_mute_if_available = "no"; // Use this optional advanced setting to control whether the hardware in the DAC is used for muting. Default is "no", for compatibility with other audio players. }; // Parameters for the "sndio" audio back end. All are optional. sndio = { // device = "snd/0"; // optional setting to set the name of the output device. Default is the sndio system default. // rate = 44100; // optional setting which can be 44100, 88200, 176400 or 352800, but the device must have the capability. Default is 44100. // format = "S16"; // optional setting which can be "U8", "S8", "S16", "S24", "S24_3LE", "S24_3BE" or "S32", but the device must have the capability. Except where stated using (*LE or *BE), endianness matches that of the processor. // round = <number>; // advanced optional setting to set the period size near to this value // bufsz = <number>; // advanced optional setting to set the buffer size near to this value }; // Parameters for the "pa" PulseAudio backend. pa = { // application_name = "Shairport Sync"; //Set this to the name that should appear in the Sounds "Applications" tab when Shairport Sync is active. }; // Parameters for the "pipe" audio back end, a back end that directs raw CD-style audio output to a pipe. No interpolation is done. pipe = { // name = "/path/to/pipe"; // there is no default pipe name for the output }; // These are no configuration file parameters for the "stdout" audio back end. No interpolation is done. // These are no configuration file parameters for the "ao" audio back end. No interpolation is done. // Static latency settings are deprecated and the settings have been removed. dsp = { ////////////////////////////////////////// // This convolution filter can be used to apply almost any correction to the audio signal, like frequency and phase correction. // For example you could measure (with a good microphone and a sweep-sine) the frequency response of your speakers + room, // and apply a correction to get a flat response curve. ////////////////////////////////////////// // // convolution = "yes"; // Activate the convolution filter. // convolution_ir_file = "impulse.wav"; // Impulse Response file to be convolved to the audio stream // convolution_gain = -4.0; // Static gain applied to prevent clipping during the convolution process // convolution_max_length = 44100; // Truncate the input file to this length in order to save CPU. ////////////////////////////////////////// // This loudness filter is used to compensate for human ear non linearity. // When the volume decreases, our ears loose more sentisitivity in the low range frequencies than in the mid range ones. // This filter aims at compensating for this loss, applying a variable gain to low frequencies depending on the volume. // More info can be found here: https://en.wikipedia.org/wiki/Equal-loudness_contour // For this filter to work properly, you should disable (or set to a fix value) all other volume control and only let shairport-sync control your volume. // The setting "loudness_reference_volume_db" should be set at the volume reported by shairport-sync when listening to music at a normal listening volume. ////////////////////////////////////////// // // loudness = "yes"; // Activate the filter // loudness_reference_volume_db = -20.0; // Above this level the filter will have no effect anymore. Below this level it will gradually boost the low frequencies. }; // How to deal with metadata, including artwork metadata = { // enabled = "no"; // set this to yes to get Shairport Sync to solicit metadata from the source and to pass it on via a pipe // include_cover_art = "no"; // set to "yes" to get Shairport Sync to solicit cover art from the source and pass it via the pipe. You must also set "enabled" to "yes". // pipe_name = "/tmp/shairport-sync-metadata"; // pipe_timeout = 5000; // wait for this number of milliseconds for a blocked pipe to unblock before giving up // socket_address = "226.0.0.1"; // if set to a host name or IP address, UDP packets containing metadata will be sent to this address. May be a multicast address. "socket-port" must be non-zero and "enabled" must be set to yes" // socket_port = 5555; // if socket_address is set, the port to send UDP packets to // socket_msglength = 65000; // the maximum packet size for any UDP metadata. This will be clipped to be between 500 or 65000. The default is 500. }; // Diagnostic settings. These are for diagnostic and debugging only. Normally you sould leave them commented out diagnostics = { // disable_resend_requests = "no"; // set this to yes to stop Shairport Sync from requesting the retransmission of missing packets. Default is "no". // statistics = "no"; // set to "yes" to print statistics in the log // log_verbosity = 0; // "0" means no debug verbosity, "3" is most verbose. // log_show_time_since_startup = "no"; // set this to yes if you want the time since startup in the debug message -- seconds down to nanoseconds // log_show_time_since_last_message = "no"; // set this to yes if you want the time since the last debug message in the debug message -- seconds down to nanoseconds // drop_this_fraction_of_audio_packets = 0.0; // use this to simulate a noisy network where this fraction of UDP packets are lost in transmission. E.g. a value of 0.001 would mean an average of 0.1% of packets are lost, which is actually quite a high figure. }; -- no debconf information
