> We switched to the new persistent interface naming scheme in 220-7. > > Can you tell use, what interface names you had before the upgrade (via > > and what you get after the upgrade? > > What's the ifconfig -a output before and after the upgrade? > ifconfig -a with 215-18
eth1 Link encap:Ethernet HWaddr 00:40:f4:5a:22:14
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth3 Link encap:Ethernet HWaddr bc:5f:f4:b0:ce:33
inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.224
inet6 addr: fe80::be5f:f4ff:feb0:ce33/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:17357982 errors:0 dropped:0 overruns:0 frame:0
TX packets:10333457 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:23770406556 (22.1 GiB) TX bytes:1305235119 (1.2 GiB)
Interrupt:20 Memory:f0500000-f0520000
eth3.10 Link encap:Ethernet HWaddr bc:5f:f4:b0:ce:33
inet6 addr: fe80::be5f:f4ff:feb0:ce33/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2843 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:378119 (369.2 KiB) TX bytes:738 (738.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1030 (1.0 KiB) TX bytes:1030 (1.0 KiB)
Now cant install new udev and reboot, but in ifconfig -a was "eth1" and
"renamed" or "renamed1"
>
> Is this a virtual machine?
No, this is real hardware
>
> Can you attach your /etc/udev/rules.d/70-persistent-net.rules
>
Also while i boot with 220-7, boot was very slow, and in console was message
something like network slow or not working.
grep "eth" from dmesg boot with 215-18:
[ 1.347094] 8139too 0000:03:01.0 eth0: RealTek RTL8139 at
0xffffc90003148000, 00:40:f4:5a:22:14, IRQ 19
[ 6.217538] e1000e 0000:00:19.0 eth1: registered PHC clock
[ 6.217539] e1000e 0000:00:19.0 eth1: (PCI Express:2.5GT/s:Width x1)
bc:5f:f4:b0:ce:33
[ 6.217539] e1000e 0000:00:19.0 eth1: Intel(R) PRO/1000 Network Connection
[ 6.217587] e1000e 0000:00:19.0 eth1: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
[ 11.331006] [drm:intel_opregion_setup] Public ACPI methods supported
[ 11.336695] [drm:intel_dsm_pci_probe] no _DSM method for intel device
[ 13.315529] 8139too 0000:03:01.0 rename2: renamed from eth0
[ 13.324942] systemd-udevd[560]: renamed network interface eth0 to rename2
[ 13.518739] e1000e 0000:00:19.0 eth3: renamed from eth1
[ 13.526391] 8139too 0000:03:01.0 eth1: renamed from rename2
[ 13.526394] systemd-udevd[568]: renamed network interface eth1 to eth3
[ 13.535314] systemd-udevd[560]: renamed network interface eth0 to eth1
[ 21.082465] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 21.083235] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 22.496925] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 23.515636] IPv6: ADDRCONF(NETDEV_UP): eth3.10: link is not ready
[ 26.113628] e1000e: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
None
[ 26.114409] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[ 26.115256] IPv6: ADDRCONF(NETDEV_CHANGE): eth3.10: link becomes ready
and grep "eth" from dmesg boot with 220-7
[ 1.345592] 8139too 0000:03:01.0 eth0: RealTek RTL8139 at
0xffffc90008190000, 00:40:f4:5a:22:14, IRQ 19
[ 1.481367] e1000e 0000:00:19.0 eth1: registered PHC clock
[ 1.481368] e1000e 0000:00:19.0 eth1: (PCI Express:2.5GT/s:Width x1)
bc:5f:f4:b0:ce:33
[ 1.481368] e1000e 0000:00:19.0 eth1: Intel(R) PRO/1000 Network Connection
[ 1.481405] e1000e 0000:00:19.0 eth1: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
[ 10.739090] [drm:intel_opregion_setup] Public ACPI methods supported
[ 10.744202] [drm:intel_dsm_pci_probe] no _DSM method for intel device
[ 12.181475] 8139too 0000:03:01.0 rename2: renamed from eth0
[ 107.297643] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
70-persistent-net.rules
Description: Binary data
