Package: src:linux
Version: 3.16.7-ckt7-1
Severity: important
Installing jessie makes XServe G5 fans run full speed all the time.
-- Package-specific info:
** Version:
Linux version 3.16.0-4-powerpc64 (debian-ker...@lists.debian.org) (gcc version
4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt7-1 (2015-03-01)
** Command line:
root=UUID=47e08bf5-e62c-4488-9715-ecc20f04b351 ro
** Not tainted
** Kernel log:
[ 6.514122] systemd[1]: Starting system-getty.slice.
[ 6.534961] systemd[1]: Created slice system-getty.slice.
[ 6.544965] systemd[1]: Starting Create list of required static device nodes
for the current kernel...
[ 6.575941] systemd[1]: Mounting Debug File System...
[ 6.597499] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.619313] systemd[1]: Mounting Huge Pages File System...
[ 6.673770] systemd[1]: Starting Load Kernel Modules...
[ 6.698216] systemd[1]: Starting udev Coldplug all Devices...
[ 6.765327] systemd[1]: Started Set Up Additional Binary Formats.
[ 6.775556] systemd[1]: Starting Journal Service...
[ 6.807087] systemd[1]: Started Journal Service.
[ 7.344876] lp: driver loaded but no devices found
[ 7.621376] systemd-udevd[171]: starting version 215
[ 8.488202] [drm] Initialized drm 1.1.0 20060810
[ 8.733873] systemd-udevd[185]: renamed network interface eth0 to eth2
[ 8.753893] systemd-udevd[186]: renamed network interface eth1 to eth3
[ 9.000653] [drm] radeon kernel modesetting enabled.
[ 9.010302] checking generic (9c008000 96000) vs hw (98000000 8000000)
[ 9.010309] fb: switching to radeondrmfb from OFfb ATY,BlueSt
[ 9.024617] Console: switching to colour dummy device 80x25
[ 9.025144] radeon 0001:06:03.0: enabling device (0086 -> 0087)
[ 9.025601] [drm] initializing kernel modesetting (RV100 0x1002:0x5159
0x1002:0x0908).
[ 9.026603] [drm] register mmio base: 0x90080000
[ 9.026623] [drm] register mmio size: 65536
[ 9.163941] [drm] Not an x86 BIOS ROM, not using.
[ 9.173981] [drm] Using device-tree clock info
[ 9.174005] radeon 0001:06:03.0: VRAM: 128M 0x0000000098000000 -
0x000000009FFFFFFF (64M used)
[ 9.174014] radeon 0001:06:03.0: GTT: 512M 0x0000000078000000 -
0x0000000097FFFFFF
[ 9.178774] [drm] Detected VRAM RAM=128M, BAR=128M
[ 9.178792] [drm] RAM width 64bits DDR
[ 9.178972] [TTM] Zone kernel: Available graphics memory: 2040832 kiB
[ 9.178980] [TTM] Initializing pool allocator
[ 9.179111] [drm] radeon: 64M of VRAM memory ready
[ 9.179123] [drm] radeon: 512M of GTT memory ready.
[ 9.179181] [drm] GART: num cpu pages 8192, num gpu pages 131072
[ 9.201437] [drm] PCI GART of 512M enabled (table at 0x0000000062180000).
[ 9.201655] radeon 0001:06:03.0: WB disabled
[ 9.201676] radeon 0001:06:03.0: fence driver on ring 0 use gpu addr
0x0000000078000000 and cpu addr 0xc000000164ad0000
[ 9.201692] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 9.201697] [drm] Driver supports precise vblank timestamp query.
[ 9.201765] [drm] radeon: irq initialized.
[ 9.201809] [drm] Loading R100 Microcode
[ 9.237575] radeon 0001:06:03.0: firmware: failed to load radeon/R100_cp.bin
(-2)
[ 9.237648] [drm:r100_cp_init] *ERROR* Failed to load firmware!
[ 9.237657] radeon 0001:06:03.0: failed initializing CP (-2).
[ 9.237664] radeon 0001:06:03.0: Disabling GPU acceleration
[ 9.237692] [drm] radeon: cp finalized
[ 9.238134] i2c i2c-5: therm_pm72: attach_adapter method is deprecated
[ 9.238146] i2c i2c-5: Please use another way to instantiate your i2c_client
[ 9.238212] i2c i2c-6: therm_pm72: attach_adapter method is deprecated
[ 9.238219] i2c i2c-6: Please use another way to instantiate your i2c_client
[ 9.238272] i2c i2c-7: therm_pm72: attach_adapter method is deprecated
[ 9.238279] i2c i2c-7: Please use another way to instantiate your i2c_client
[ 9.238334] i2c i2c-8: therm_pm72: attach_adapter method is deprecated
[ 9.238341] i2c i2c-8: Please use another way to instantiate your i2c_client
[ 9.246611] [drm] Connector Table: 1 (generic)
[ 9.246652] [drm] No TMDS info found in BIOS
[ 9.246663] [drm] No TV DAC info found in BIOS
[ 9.246944] [drm] Radeon Display Connectors
[ 9.246950] [drm] Connector 0:
[ 9.246954] [drm] DVI-I-1
[ 9.246958] [drm] HPD1
[ 9.246964] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 9.246968] [drm] Encoders:
[ 9.246973] [drm] DFP1: INTERNAL_TMDS1
[ 9.246977] [drm] CRT2: INTERNAL_DAC2
[ 9.246982] [drm] Connector 1:
[ 9.246986] [drm] VGA-1
[ 9.246991] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 9.247004] [drm] Encoders:
[ 9.247005] [drm] CRT1: INTERNAL_DAC1
[ 9.247006] [drm] Connector 2:
[ 9.247006] [drm] SVIDEO-1
[ 9.247007] [drm] Encoders:
[ 9.247008] [drm] TV1: INTERNAL_DAC2
[ 9.345904] [drm] fb mappable at 0x98040000
[ 9.345923] [drm] vram apper at 0x98000000
[ 9.345947] [drm] size 5242880
[ 9.345952] [drm] fb depth is 24
[ 9.345956] [drm] pitch is 5120
[ 9.494053] Console: switching to colour frame buffer device 160x64
[ 9.526526] radeon 0001:06:03.0: fb0: radeondrmfb frame buffer device
[ 9.526528] radeon 0001:06:03.0: registered panic notifier
[ 9.541748] [drm] Initialized radeon 2.39.0 20080528 for 0001:06:03.0 on
minor 0
[ 9.572329] Adding 9974656k swap on /dev/sda4. Priority:-1 extents:1
across:9974656k FS
[ 9.724728] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro
[ 9.756432] systemd-journald[156]: Received request to flush runtime journal
from PID 1
[ 10.218020] tg3 0001:07:04.0: firmware: failed to load tigon/tg3_tso.bin (-2)
[ 10.218026] tg3 0001:07:04.0 eth2: TSO capability disabled
[ 10.266563] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 10.930076] RPC: Registered named UNIX socket transport module.
[ 10.941662] RPC: Registered udp transport module.
[ 10.953254] RPC: Registered tcp transport module.
[ 10.964845] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.014754] FS-Cache: Loaded
[ 11.067406] FS-Cache: Netfs 'nfs' registered for caching
[ 11.160601] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 13.408617] tg3 0001:07:04.0 eth2: Link is up at 1000 Mbps, full duplex
[ 13.419173] tg3 0001:07:04.0 eth2: Flow control is on for TX and on for RX
[ 13.429850] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
** Model information
revision : 3.0 (pvr 003c 0300)
revision : 3.0 (pvr 003c 0300)
platform : PowerMac
model : RackMac3,1
machine : RackMac3,1
motherboard : RackMac3,1 MacRISC4 Power Macintosh
** Loaded modules:
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
fscache
sunrpc
radeon
ttm
drm_kms_helper
evdev
drm
i2c_algo_bit
windfarm_smu_sat
windfarm_pid
parport_pc
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
hid_generic
usbhid
hid
sd_mod
crc_t10dif
crct10dif_generic
crct10dif_common
ata_generic
sg
therm_pm72
windfarm_max6690_sensor
windfarm_lm75_sensor
windfarm_core
ohci_pci
ohci_hcd
ehci_pci
ehci_hcd
firewire_ohci
tg3
ptp
sr_mod
cdrom
sata_svw
firewire_core
crc_itu_t
usbcore
usb_common
pps_core
libphy
** PCI devices:
0000:f0:0b.0 Host bridge [0600]: Apple Inc. U3H AGP Bridge [106b:0059]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Capabilities: <access denied>
Kernel driver in use: agpgart-uninorth
0001:00:00.0 Host bridge [0600]: Apple Inc. U3 HT Bridge [106b:0057]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
0001:00:01.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] AMD-8131
PCI-X Bridge [1022:7450] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 90000000-9fffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:02.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] AMD-8131
PCI-X Bridge [1022:7450] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Memory behind bridge: a0000000-a00fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:03.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0045]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:04.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0046]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: 80100000-801fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:05.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0047]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: 80200000-802fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:06.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0048]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Memory behind bridge: 80300000-805fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:07.0 PCI bridge [0604]: Apple Inc. K2 HT-PCI Bridge [106b:0049]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: 80600000-806fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:01:07.0 Unassigned class [ff00]: Apple Inc. K2 KeyLargo Mac/IO [106b:0041]
(rev 60)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 64 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
Kernel driver in use: macio
0001:02:0b.0 USB controller [0c03]: NEC Corporation OHCI USB Controller
[1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB Controller [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 63
Region 0: Memory at 80102000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci-pci
0001:02:0b.1 USB controller [0c03]: NEC Corporation OHCI USB Controller
[1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB Controller [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 63
Region 0: Memory at 80101000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci-pci
0001:02:0b.2 USB controller [0c03]: NEC Corporation uPD72010x USB 2.0
Controller [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation uPD72010x USB 2.0 Controller [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 63
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
0001:03:0d.0 Unassigned class [ff00]: Apple Inc. K2 ATA/100 [106b:0043]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 39
Region 0: Memory at 80204000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: pata-pci-macio
0001:03:0e.0 FireWire (IEEE 1394) [0c00]: Apple Inc. K2 FireWire [106b:0042]
(prog-if 10 [OHCI])
Subsystem: Apple Inc. Device [106b:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
0001:05:0c.0 IDE interface [0101]: Broadcom K2 SATA [1166:0240] (prog-if 8f
[Master SecP SecO PriP PriO])
Subsystem: Broadcom K2 SATA [1166:0240]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Interrupt: pin ? routed to IRQ 17
Region 0: I/O ports at <unassigned> [disabled]
Region 1: I/O ports at <unassigned> [disabled]
Region 2: I/O ports at <unassigned> [disabled]
Region 3: I/O ports at <unassigned> [disabled]
Region 4: I/O ports at <unassigned> [disabled]
Region 5: Memory at 80600000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: sata_svw
0001:06:03.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc.
[AMD/ATI] RV100 [Radeon 7000 / Radeon VE] [1002:5159] (prog-if 00 [VGA
controller])
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] XVR-100 (supplied by
Sun) [1002:0908]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at 98000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at 90080000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at 90000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
0001:07:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704
Gigabit Ethernet [14e4:1648] (rev 03)
Subsystem: Apple Inc. Device [106b:005a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 54
Region 0: Memory at a0030000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at a0020000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
0001:07:04.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704
Gigabit Ethernet [14e4:1648] (rev 03)
Subsystem: Apple Inc. Device [106b:005a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 57
Region 0: Memory at a0010000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at a0000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 004: ID 05ac:0301 Apple, Inc. USB Mouse [Mitsumi, M4848]
Bus 002 Device 003: ID 05ac:0201 Apple, Inc. USB Keyboard [Alps or Logitech,
M2452]
Bus 002 Device 002: ID 05ac:1001 Apple, Inc. Keyboard Hub [ALPS]
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 8.0
APT prefers testing-updates
APT policy: (500, 'testing-updates'), (500, 'testing')
Architecture: powerpc (ppc64)
Kernel: Linux 3.16.0-4-powerpc64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-3.16.0-4-powerpc64 depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.119
ii kmod 18-3
ii linux-base 3.5
Versions of packages linux-image-3.16.0-4-powerpc64 recommends:
pn firmware-linux-free <none>
pn irqbalance <none>
Versions of packages linux-image-3.16.0-4-powerpc64 suggests:
pn debian-kernel-handbook <none>
pn linux-doc-3.16 <none>
pn mkvmlinuz <none>
Versions of packages linux-image-3.16.0-4-powerpc64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16.0-4-powerpc64/postinst/mips-initrd-3.16.0-4-powerpc64:
linux-image-3.16.0-4-powerpc64/prerm/removing-running-kernel-3.16.0-4-powerpc64:
true
linux-image-3.16.0-4-powerpc64/postinst/depmod-error-initrd-3.16.0-4-powerpc64:
false
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
