Package: src:linux
Version: 3.7.8-1~experimental.1
Severity: normal
Subject says most of it. These are new components: PCIe card with that
Marvell chip, 4 exposed SATA 6G ports, one WD Red 3TB on each port.
Disks are fine according to SMART conveyance test.
Console action:
maik@antares:~/ > sudo mdadm -C linux-data -n 4 -l 5 /dev/sde /dev/sdf /dev/sdg
/dev/sdh
mdadm: /dev/sde appears to be part of a raid array:
level=raid5 devices=4 ctime=Tue Feb 19 22:47:42 2013
mdadm: /dev/sdf appears to be part of a raid array:
level=raid5 devices=4 ctime=Tue Feb 19 22:47:42 2013
mdadm: /dev/sdg appears to be part of a raid array:
level=raid5 devices=4 ctime=Tue Feb 19 22:47:42 2013
mdadm: /dev/sdh appears to be part of a raid array:
level=raid5 devices=4 ctime=Tue Feb 19 22:47:42 2013
Continue creating array? y
mdadm: Defaulting to version 1.2 metadata
mdadm: array /dev/md/linux-data started.
maik@antares:~/ > cat /proc/mdstat
Personalities : [raid6] [raid5] [raid4]
md127 : active raid5 sdh[4] sdg[2] sdf[1] sde[0]
8790405120 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [UUU_]
[>....................] recovery = 0.0% (679936/2930135040)
finish=574.4min speed=84992K/sec
unused devices: <none>
maik@antares:~/ > sudo smartctl -H /dev/sdg
smartctl 5.43 2012-06-05 r3561 [x86_64-linux-3.7-trunk-amd64] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
maik@antares:~/ > sudo smartctl -H /dev/sdg
smartctl 5.43 2012-06-05 r3561 [x86_64-linux-3.7-trunk-amd64] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
maik@antares:~/ > sudo smartctl -H /dev/sdg
smartctl 5.43 2012-06-05 r3561 [x86_64-linux-3.7-trunk-amd64] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
Error SMART Thresholds Read failed: scsi error aborted command
Smartctl: SMART Read Thresholds failed.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.
I've extended the kernel log below so it covers everything from the
moment of RAID creation, including the failing SMART command.
The problem seems fairly repeatable, so far every attempt at creating a
RAID has failed this way (because smartd eventually pings the disks).
-- Package-specific info:
** Version:
Linux version 3.7-trunk-amd64 (debian-ker...@lists.debian.org) (gcc version
4.7.2 (Debian 4.7.2-5) ) #1 SMP Debian 3.7.8-1~experimental.1
** Command line:
BOOT_IMAGE=/vmlinuz-3.7-trunk-amd64
root=UUID=06cc1c4c-d190-49bb-9219-0ccfa22e2661 ro acpi_os=Linux quiet
** Tainted: PO (4097)
* Proprietary module has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[ 122.445618] md: bind<sde>
[ 122.445783] md: bind<sdf>
[ 122.445952] md: bind<sdg>
[ 122.456452] md: bind<sdh>
[ 122.459351] async_tx: api initialized (async)
[ 122.460092] xor: automatically using best checksumming function:
[ 122.499742] avx : 11990.000 MB/sec
[ 122.567597] raid6: sse2x1 4318 MB/s
[ 122.635438] raid6: sse2x2 5419 MB/s
[ 122.703278] raid6: sse2x4 6137 MB/s
[ 122.703280] raid6: using algorithm sse2x4 (6137 MB/s)
[ 122.703282] raid6: using ssse3x2 recovery algorithm
[ 122.706977] md: raid6 personality registered for level 6
[ 122.706981] md: raid5 personality registered for level 5
[ 122.706983] md: raid4 personality registered for level 4
[ 122.707309] md/raid:md127: device sdg operational as raid disk 2
[ 122.707312] md/raid:md127: device sdf operational as raid disk 1
[ 122.707314] md/raid:md127: device sde operational as raid disk 0
[ 122.707711] md/raid:md127: allocated 4338kB
[ 122.707797] md/raid:md127: raid level 5 active with 3 out of 4 devices,
algorithm 2
[ 122.707799] RAID conf printout:
[ 122.707801] --- level:5 rd:4 wd:3
[ 122.707803] disk 0, o:1, dev:sde
[ 122.707805] disk 1, o:1, dev:sdf
[ 122.707806] disk 2, o:1, dev:sdg
[ 122.707833] md127: detected capacity change from 0 to 9001374842880
[ 122.707860] RAID conf printout:
[ 122.707865] --- level:5 rd:4 wd:3
[ 122.707868] disk 0, o:1, dev:sde
[ 122.707870] disk 1, o:1, dev:sdf
[ 122.707872] disk 2, o:1, dev:sdg
[ 122.707873] disk 3, o:1, dev:sdh
[ 122.707965] md: recovery of RAID array md127
[ 122.707968] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 122.707970] md: using maximum available idle IO bandwidth (but not more than
200000 KB/sec) for recovery.
[ 122.707973] md: using 128k window, over a total of 2930135040k.
[ 122.740153] md127: unknown partition table
[ 180.531641] ata9.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 180.531648] ata9.00: failed command: SMART
[ 180.531655] ata9.00: cmd b0/d1:01:01:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
[ 180.531655] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4
(timeout)
[ 180.531658] ata9.00: status: { DRDY }
[ 180.531666] ata9: hard resetting link
[ 185.887433] ata9: link is slow to respond, please be patient (ready=0)
[ 190.524871] ata9: COMRESET failed (errno=-16)
[ 190.524877] ata9: hard resetting link
[ 195.872694] ata9: link is slow to respond, please be patient (ready=0)
[ 200.510134] ata9: COMRESET failed (errno=-16)
[ 200.510141] ata9: hard resetting link
[ 205.857925] ata9: link is slow to respond, please be patient (ready=0)
[ 235.470518] ata9: COMRESET failed (errno=-16)
[ 235.470526] ata9: limiting SATA link speed to 3.0 Gbps
[ 235.470529] ata9: hard resetting link
[ 240.483102] ata9: COMRESET failed (errno=-16)
[ 240.483110] ata9: reset failed, giving up
[ 240.483112] ata9.00: disabled
[ 240.483134] ata9: EH complete
[ 240.483185] sd 8:0:0:0: [sdg] Unhandled error code
[ 240.483188] sd 8:0:0:0: [sdg]
[ 240.483191] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 240.483193] sd 8:0:0:0: [sdg] CDB:
[ 240.483195] Read(10): 28 00 00 63 18 00 00 04 00 00
[ 240.483203] end_request: I/O error, dev sdg, sector 6494208
[ 240.483207] md/raid:md127: read error not correctable (sector 6494208 on
sdg).
[ 240.483211] md/raid:md127: Disk failure on sdg, disabling device.
[ 240.483211] md/raid:md127: Operation continuing on 2 devices.
[ 240.483219] md/raid:md127: read error not correctable (sector 6494216 on
sdg).
[ 240.483222] md/raid:md127: read error not correctable (sector 6494224 on
sdg).
[ 240.483224] md/raid:md127: read error not correctable (sector 6494232 on
sdg).
[ 240.483226] md/raid:md127: read error not correctable (sector 6494240 on
sdg).
[ 240.483229] md/raid:md127: read error not correctable (sector 6494248 on
sdg).
[ 240.483231] md/raid:md127: read error not correctable (sector 6494256 on
sdg).
[ 240.483233] md/raid:md127: read error not correctable (sector 6494264 on
sdg).
[ 240.483235] md/raid:md127: read error not correctable (sector 6494272 on
sdg).
[ 240.483238] md/raid:md127: read error not correctable (sector 6494280 on
sdg).
[ 240.483308] sd 8:0:0:0: [sdg] Unhandled error code
[ 240.483310] sd 8:0:0:0: [sdg]
[ 240.483312] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 240.483314] sd 8:0:0:0: [sdg] CDB:
[ 240.483315] Read(10): 28 00 00 63 1c 00 00 04 00 00
[ 240.483322] end_request: I/O error, dev sdg, sector 6495232
[ 301.216814] ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 301.216818] ata7.00: failed command: FLUSH CACHE EXT
[ 301.216821] ata7.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 301.216821] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4
(timeout)
[ 301.216822] ata7.00: status: { DRDY }
[ 301.216827] ata7: hard resetting link
[ 301.216842] ata10.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 301.216845] ata10.00: failed command: FLUSH CACHE EXT
[ 301.216849] ata10.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 301.216849] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4
(timeout)
[ 301.216851] ata10.00: status: { DRDY }
[ 301.216855] ata10: hard resetting link
[ 301.216861] ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 301.216864] ata8.00: failed command: FLUSH CACHE EXT
[ 301.216868] ata8.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[ 301.216868] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4
(timeout)
[ 301.216870] ata8.00: status: { DRDY }
[ 301.216874] ata8: hard resetting link
[ 302.038921] ata10: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 302.038945] ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 302.038966] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 307.027548] ata7.00: qc timeout (cmd 0xec)
[ 307.027562] ata8.00: qc timeout (cmd 0xec)
[ 307.027574] ata10.00: qc timeout (cmd 0xec)
[ 307.530401] ata8.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 307.530406] ata8.00: revalidation failed (errno=-5)
[ 307.530413] ata8: hard resetting link
[ 307.530423] ata7.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 307.530428] ata7.00: revalidation failed (errno=-5)
[ 307.530433] ata7: hard resetting link
[ 307.530442] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 307.530446] ata10.00: revalidation failed (errno=-5)
[ 307.530451] ata10: hard resetting link
[ 308.352538] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 308.352559] ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 308.352580] ata10: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 318.329827] ata8.00: qc timeout (cmd 0xec)
[ 318.329840] ata7.00: qc timeout (cmd 0xec)
[ 318.329851] ata10.00: qc timeout (cmd 0xec)
[ 318.832656] ata7.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 318.832661] ata7.00: revalidation failed (errno=-5)
[ 318.832666] ata7: limiting SATA link speed to 3.0 Gbps
[ 318.832671] ata7: hard resetting link
[ 318.832681] ata8.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 318.832685] ata8.00: revalidation failed (errno=-5)
[ 318.832689] ata8: limiting SATA link speed to 3.0 Gbps
[ 318.832693] ata8: hard resetting link
[ 318.832703] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 318.832707] ata10.00: revalidation failed (errno=-5)
[ 318.832711] ata10: limiting SATA link speed to 3.0 Gbps
[ 318.832715] ata10: hard resetting link
[ 319.654789] ata10: SATA link up 6.0 Gbps (SStatus 133 SControl 320)
[ 319.654811] ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 320)
[ 319.654831] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 320)
[ 349.586621] ata7.00: qc timeout (cmd 0xec)
[ 349.586636] ata10.00: qc timeout (cmd 0xec)
[ 349.586656] ata8.00: qc timeout (cmd 0xec)
[ 350.089487] ata8.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 350.089492] ata8.00: revalidation failed (errno=-5)
[ 350.089496] ata8.00: disabled
[ 350.089506] ata8.00: device reported invalid CHS sector 0
[ 350.089517] ata7.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 350.089521] ata7.00: revalidation failed (errno=-5)
[ 350.089524] ata7.00: disabled
[ 350.089532] ata7.00: device reported invalid CHS sector 0
[ 350.089543] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 350.089548] ata10.00: revalidation failed (errno=-5)
[ 350.089551] ata10.00: disabled
[ 350.089559] ata10.00: device reported invalid CHS sector 0
[ 350.592344] ata10: hard resetting link
[ 350.592359] ata7: hard resetting link
[ 350.592373] ata8: hard resetting link
[ 351.414474] ata10: SATA link up 6.0 Gbps (SStatus 133 SControl 320)
[ 351.414496] ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 320)
[ 351.414517] ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 320)
[ 351.917332] ata8: EH complete
[ 351.917338] ata7: EH complete
[ 351.917352] ata10: EH complete
[ 351.917370] sd 7:0:0:0: [sdf] Unhandled error code
[ 351.917372] sd 6:0:0:0: [sde] Unhandled error code
[ 351.917375] sd 6:0:0:0: [sde]
[ 351.917377] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 351.917379] sd 6:0:0:0: [sde] CDB:
[ 351.917385] sd 9:0:0:0: [sdh] Unhandled error code
[ 351.917388] sd 7:0:0:0: [sdf]
[ 351.917389] sd 9:0:0:0: [sdh]
[ 351.917391] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 351.917392] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 351.917394] sd 7:0:0:0: [sdf] CDB:
[ 351.917395] sd 9:0:0:0: [sdh] CDB:
[ 351.917380] Write(10): 2a
[ 351.917396] Write(10)Write(10):: 2a 2a 00 00 00 00 00 00 00 00 08 08 00 00
00 00 01 01 00 00
[ 351.917418]
[ 351.917420] end_request: I/O error, dev sdf, sector 8
[ 351.917421] end_request: I/O error, dev sdh, sector 8
[ 351.917423] end_request: I/O error, dev sdf, sector 8
[ 351.917424] end_request: I/O error, dev sdh, sector 8
[ 351.917426] md: super_written gets error=-5, uptodate=0
[ 351.917427] md: super_written gets error=-5, uptodate=0
[ 351.917430] md/raid:md127: Disk failure on sdf, disabling device.
[ 351.917430] md/raid:md127: Operation continuing on 1 devices.
[ 351.917432] md/raid:md127: Disk failure on sdh, disabling device.
[ 351.917432] md/raid:md127: Operation continuing on 1 devices.
[ 351.917444] 00 00 00 00 08 00 00 01 00
[ 351.917451] end_request: I/O error, dev sde, sector 8
[ 351.917454] end_request: I/O error, dev sde, sector 8
[ 351.917456] md: super_written gets error=-5, uptodate=0
[ 351.917459] md/raid:md127: Disk failure on sde, disabling device.
[ 351.917459] md/raid:md127: Operation continuing on 0 devices.
[ 351.921299] md: md127: recovery done.
[ 351.921543] RAID conf printout:
[ 351.921548] --- level:5 rd:4 wd:0
[ 351.921550] disk 0, o:0, dev:sde
[ 351.921552] disk 1, o:0, dev:sdf
[ 351.921553] disk 2, o:0, dev:sdg
[ 351.921555] disk 3, o:0, dev:sdh
[ 351.925329] RAID conf printout:
[ 351.925333] --- level:5 rd:4 wd:0
[ 351.925336] disk 0, o:0, dev:sde
[ 351.925338] disk 1, o:0, dev:sdf
[ 351.925340] disk 2, o:0, dev:sdg
[ 351.925346] RAID conf printout:
[ 351.925347] --- level:5 rd:4 wd:0
[ 351.925349] disk 0, o:0, dev:sde
[ 351.925351] disk 1, o:0, dev:sdf
[ 351.925352] disk 2, o:0, dev:sdg
[ 351.929384] RAID conf printout:
[ 351.929389] --- level:5 rd:4 wd:0
[ 351.929392] disk 0, o:0, dev:sde
[ 351.929394] disk 1, o:0, dev:sdf
[ 351.929398] RAID conf printout:
[ 351.929399] --- level:5 rd:4 wd:0
[ 351.929401] disk 0, o:0, dev:sde
[ 351.929403] disk 1, o:0, dev:sdf
[ 351.937283] RAID conf printout:
[ 351.937288] --- level:5 rd:4 wd:0
[ 351.937291] disk 0, o:0, dev:sde
[ 351.937295] RAID conf printout:
[ 351.937297] --- level:5 rd:4 wd:0
[ 351.937299] disk 0, o:0, dev:sde
[ 351.948780] RAID conf printout:
[ 351.948785] --- level:5 rd:4 wd:0
** Model information
sys_vendor: System manufacturer
product_name: System Product Name
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 3202
board_vendor: ASUSTeK COMPUTER INC.
board_name: P8C WS
board_version: Rev 1.xx
** Loaded modules:
raid456
async_raid6_recov
async_memcpy
async_pq
raid6_pq
async_xor
xor
async_tx
fuse
parport_pc
ppdev
lp
parport
bnep
rfcomm
bluetooth
cpufreq_stats
crc16
cpufreq_userspace
cpufreq_powersave
cpufreq_conservative
uinput
nls_utf8
nls_cp437
vfat
fat
ecryptfs
md_mod
snd_hda_codec_hdmi
joydev
snd_usb_audio
snd_usbmidi_lib
snd_seq_midi
snd_seq_midi_event
uvcvideo
videobuf2_vmalloc
videobuf2_memops
snd_rawmidi
videobuf2_core
videodev
media
snd_hda_codec_realtek
iTCO_wdt
iTCO_vendor_support
eeepc_wmi
asus_wmi
sparse_keymap
rfkill
evdev
coretemp
kvm_intel
snd_hda_intel
snd_hda_codec
fglrx(PO)
psmouse
snd_hwdep
kvm
snd_pcm
snd_page_alloc
i2c_i801
snd_seq
pcspkr
serio_raw
snd_seq_device
snd_timer
lpc_ich
i2c_core
mfd_core
snd
soundcore
mei
acpi_cpufreq
mperf
wmi
video
button
processor
xfs
btrfs
libcrc32c
zlib_deflate
sha256_generic
dm_crypt
efivars
dm_mirror
dm_region_hash
dm_log
hid_cherry
hid_generic
usbhid
usb_storage
hid
dm_mod
sg
sd_mod
crc_t10dif
crc32c_intel
ghash_clmulni_intel
aesni_intel
aes_x86_64
ablk_helper
cryptd
xts
lrw
gf128mul
microcode
fan
thermal
thermal_sys
ahci
libahci
e1000e
ehci_hcd
xhci_hcd
libata
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/Ivy Bridge DRAM
Controller [8086:0158] (rev 09)
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core
processor PCI Express Root Port [8086:0151] (rev 09) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: e0000000-f00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:06.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core
processor PCI Express Root Port [8086:015d] (rev 09) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f0300000-f03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0400000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series
Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 52
Region 0: Memory at f041b000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0418000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset
Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:84fb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at f0410000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 6 [8086:1e1a] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f0200000-f02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.6 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset
Family PCI Express Root Port 7 [8086:1e1c] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: f0100000-f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0417000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
a4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation C216 Series Chipset LPC Controller
[8086:1e53] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series/C210 Series Chipset
Family 6-port SATA Controller [AHCI mode] [8086:1e02] (rev 04) (prog-if 01
[AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 47
Region 0: I/O ports at f070 [size=8]
Region 1: I/O ports at f060 [size=4]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at f0416000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family
SMBus Controller [8086:1e22] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:852f]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f0415000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI
Cape Verde [Radeon HD 7700 Series] [1002:683d] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:042b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 55
Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at f0000000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at e000 [size=256]
Expansion ROM at f0040000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: fglrx_pci
01:00.1 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI Device
[1002:aab0]
Subsystem: ASUSTeK Computer Inc. Device [1043:aab0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 54
Region 0: Memory at f0060000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
02:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9230 PCIe
SATA 6Gb/s Controller [1b4b:9230] (rev 10) (prog-if 01 [AHCI 1.0])
Subsystem: Marvell Technology Group Ltd. 88SE9230 PCIe SATA 6Gb/s
Controller [1b4b:9230]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: I/O ports at d050 [size=8]
Region 1: I/O ports at d040 [size=4]
Region 2: I/O ports at d030 [size=8]
Region 3: I/O ports at d020 [size=4]
Region 4: I/O ports at d000 [size=32]
Region 5: Memory at f0310000 (32-bit, non-prefetchable) [size=2K]
Expansion ROM at f0300000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
04:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network
Connection [8086:10d3]
Subsystem: ASUSTeK Computer Inc. Device [1043:8369]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f0200000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at c000 [size=32]
Region 3: Memory at f0220000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: e1000e
05:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network
Connection [8086:10d3]
Subsystem: ASUSTeK Computer Inc. Device [1043:8369]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0100000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at b000 [size=32]
Region 3: Memory at f0120000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: e1000e
** USB devices:
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 003 Device 004: ID 051d:0002 American Power Conversion Uninterruptible
Power Supply
Bus 003 Device 005: ID 090c:1000 Silicon Motion, Inc. - Taiwan (formerly Feiya
Technology Corp.) 64MB QDI U2 DISK
Bus 003 Device 006: ID 2433:b111
Bus 004 Device 003: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 004 Device 004: ID 046a:0023 Cherry GmbH CyMotion Master Linux Keyboard
Bus 004 Device 005: ID 046d:c03d Logitech, Inc. M-BT96a Pilot Optical Mouse
Bus 003 Device 007: ID 0424:2640 Standard Microsystems Corp. USB 2.0 Hub
Bus 003 Device 008: ID 046d:081d Logitech, Inc. HD Webcam C510
Bus 003 Device 009: ID 0424:4064 Standard Microsystems Corp. Ultra Fast Media
Reader
-- System Information:
Debian Release: 7.0
APT prefers testing
APT policy: (500, 'testing'), (400, 'unstable'), (300, 'experimental')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.7-trunk-amd64 (SMP w/4 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.7-trunk-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.7-trunk-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.7-trunk-amd64 suggests:
pn debian-kernel-handbook <none>
pn grub-pc | extlinux | lilo <none>
ii linux-doc-3.7 3.7.8-1~experimental.1
Versions of packages linux-image-3.7-trunk-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.37
ii firmware-linux-nonfree 0.37
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.7-trunk-amd64/postinst/ignoring-ramdisk:
linux-image-3.7-trunk-amd64/postinst/depmod-error-initrd-3.7-trunk-amd64:
false
linux-image-3.7-trunk-amd64/prerm/removing-running-kernel-3.7-trunk-amd64:
true
linux-image-3.7-trunk-amd64/postinst/missing-firmware-3.7-trunk-amd64:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
