Package: src:linux
Version: 3.2.21-3
Severity: important
Dear Maintainer,
Since 3.1 kernel, SATA drives connected to SAS controller (SAS1068E) using
mptsas driver cannot resume from standby mode.
They properly put into standby mode but when you attempt to resume drive (I'm
simply query file from mounted volume) the I/O error appear and the
dmesg shows something like this:
[1081238.863526] sd 12:0:8:0: [sdk] Device not ready
[1081238.863530] sd 12:0:8:0: [sdk] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[1081238.863534] sd 12:0:8:0: [sdk] Sense Key : Not Ready [current]
[1081238.863538] sd 12:0:8:0: [sdk] Add. Sense: Logical unit not ready,
initializing command required
[1081238.863543] sd 12:0:8:0: [sdk] CDB: Read(10): 28 00 a7 c5 85 d0 00 00 08 00
[1081238.863552] end_request: I/O error, dev sdk, sector 2814739920
[1081238.863938] sd 12:0:8:0: [sdk] Device not ready
[1081238.863940] sd 12:0:8:0: [sdk] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[1081238.863944] sd 12:0:8:0: [sdk] Sense Key : Not Ready [current]
[1081238.863948] sd 12:0:8:0: [sdk] Add. Sense: Logical unit not ready,
initializing command required
[1081238.863952] sd 12:0:8:0: [sdk] CDB: Read(10): 28 00 a7 c5 85 d0 00 00 08 00
[1081238.863960] end_request: I/O error, dev sdk, sector 2814739920
The only way to access device now is to physically disconnect the drive and
connect again.
I have attempted to use different 3.1 and 3.2 kernels including non-Debian
Liquiorix but the issus persists. It is not about drives, when I get back
to 3.0 kernel it works properly.
I also tried to use scan command for the controller (issuing - - - to
/sys/class/scsi_host/hostX/scan) and this won't helped as well.
I'm expecting this to get fixed especially because 3.2 become main kernel for
Wheezy.
-- Package-specific info:
** Version:
Linux version 3.2.0-3-amd64 (Debian 3.2.21-3) (debian-ker...@lists.debian.org)
(gcc version 4.6.3 (Debian 4.6.3-8) ) #1 SMP Thu Jun 28 09:07:26 UTC 2012
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-3-amd64
root=UUID=ebe3b6f4-35f3-4312-a6c1-e76f37386995 ro elevator=deadline quiet
** Not tainted
** Kernel log:
[962585.460863] sd 7:0:0:0: [sdg] Synchronizing SCSI cache
[962585.461027] sd 7:0:0:0: [sdg] Stopping disk
[962585.898722] ata7.00: disabled
[962587.690545] sd 12:0:1:0: [sdi] Synchronizing SCSI cache
[962587.691346] scsi target12:0:1: mptsas: ioc0: delete device: fw_channel 0,
fw_id 92, phy 4, sas_addr 0x4564393fd9b7ae8e
[962588.694896] sd 12:0:2:0: [sdj] Synchronizing SCSI cache
[962588.695692] scsi target12:0:2: mptsas: ioc0: delete device: fw_channel 0,
fw_id 29, phy 6, sas_addr 0x4560393edabeaa91
[962589.620054] sd 12:0:3:0: [sdk] Synchronizing SCSI cache
[962589.620844] scsi target12:0:3: mptsas: ioc0: delete device: fw_channel 0,
fw_id 93, phy 7, sas_addr 0x45603840dfbdae94
[962590.493203] sd 12:0:4:0: [sdl] Synchronizing SCSI cache
[962590.493996] scsi target12:0:4: mptsas: ioc0: delete device: fw_channel 0,
fw_id 85, phy 5, sas_addr 0x455e3c3fe0b7aa95
[962634.451324] ata7: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[962634.451360] ata7: irq_stat 0x00400000, PHY RDY changed
[962634.451395] ata7: hard resetting link
[962635.172028] ata7: SATA link down (SStatus 0 SControl 300)
[962635.172040] ata7: EH complete
[962636.366309] mptbase: ioc0: LogInfo(0x31110d00): Originator={PL},
Code={Reset}, SubCode(0x0d00) cb_idx mptbase_reply
[962636.572550] mptbase: ioc0: LogInfo(0x31110d00): Originator={PL},
Code={Reset}, SubCode(0x0d00) cb_idx mptbase_reply
[962637.390821] mptbase: ioc0: LogInfo(0x31110d00): Originator={PL},
Code={Reset}, SubCode(0x0d00) cb_idx mptbase_reply
[962637.556087] mptbase: ioc0: LogInfo(0x31110d00): Originator={PL},
Code={Reset}, SubCode(0x0d00) cb_idx mptbase_reply
[962640.712020] end_device-12:3: mptsas: ioc0: removing sata device:
fw_channel 0, fw_id 93, phy 7,sas_addr 0x45603840dfbdae94
[962640.712026] phy-12:7: mptsas: ioc0: delete phy 7, phy-obj
(0xffff8800371a0000)
[962640.712035] port-12:3: mptsas: ioc0: delete port 3, sas_addr
(0x45603840dfbdae94)
[962640.964019] end_device-12:2: mptsas: ioc0: removing sata device:
fw_channel 0, fw_id 29, phy 6,sas_addr 0x4560393edabeaa91
[962640.964025] phy-12:6: mptsas: ioc0: delete phy 6, phy-obj
(0xffff8800371a0c00)
[962640.964033] port-12:2: mptsas: ioc0: delete port 2, sas_addr
(0x4560393edabeaa91)
[962641.712019] end_device-12:4: mptsas: ioc0: removing sata device:
fw_channel 0, fw_id 85, phy 5,sas_addr 0x455e3c3fe0b7aa95
[962641.712025] phy-12:5: mptsas: ioc0: delete phy 5, phy-obj
(0xffff880037320800)
[962641.712034] port-12:4: mptsas: ioc0: delete port 4, sas_addr
(0x455e3c3fe0b7aa95)
[962641.964018] end_device-12:1: mptsas: ioc0: removing sata device:
fw_channel 0, fw_id 92, phy 4,sas_addr 0x4564393fd9b7ae8e
[962641.964024] phy-12:4: mptsas: ioc0: delete phy 4, phy-obj
(0xffff8800372c0400)
[962641.964032] port-12:1: mptsas: ioc0: delete port 1, sas_addr
(0x4564393fd9b7ae8e)
[962704.197427] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 94,
phy 5, sas_addr 0x45613f3ec6bbad93
[962704.206192] scsi 12:0:5:0: Direct-Access ATA WDC WD20EARX-00P AB51
PQ: 0 ANSI: 5
[962704.217191] sd 12:0:5:0: [sdg] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[962704.247800] sd 12:0:5:0: [sdg] Write Protect is off
[962704.247805] sd 12:0:5:0: [sdg] Mode Sense: 73 00 00 08
[962704.256018] sd 12:0:5:0: [sdg] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[962704.342152] sdg: sdg1
[962704.387502] sd 12:0:5:0: [sdg] Attached SCSI disk
[962704.584171] XFS (sdg1): Mounting Filesystem
[962704.742189] XFS (sdg1): Ending clean mount
[962709.333096] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 95,
phy 4, sas_addr 0x45613b44c4b8b29a
[962709.342459] scsi 12:0:6:0: Direct-Access ATA WDC WD20EARX-00P AB51
PQ: 0 ANSI: 5
[962709.353615] sd 12:0:6:0: [sdi] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[962709.372073] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 96,
phy 6, sas_addr 0x45613b42cab6ab98
[962709.380104] scsi 12:0:7:0: Direct-Access ATA WDC WD20EARX-00P AB51
PQ: 0 ANSI: 5
[962709.385085] sd 12:0:6:0: [sdi] Write Protect is off
[962709.385090] sd 12:0:6:0: [sdi] Mode Sense: 73 00 00 08
[962709.390501] sd 12:0:7:0: [sdj] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[962709.393357] sd 12:0:6:0: [sdi] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[962709.421578] sd 12:0:7:0: [sdj] Write Protect is off
[962709.421582] sd 12:0:7:0: [sdj] Mode Sense: 73 00 00 08
[962709.432666] sd 12:0:7:0: [sdj] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[962709.446803] mptsas: ioc0: attaching sata device: fw_channel 0, fw_id 88,
phy 7, sas_addr 0x45613d45c8bea996
[962709.455144] scsi 12:0:8:0: Direct-Access ATA WDC WD20EARX-00P AB51
PQ: 0 ANSI: 5
[962709.465388] sd 12:0:8:0: [sdk] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[962709.493616] sd 12:0:8:0: [sdk] Write Protect is off
[962709.493621] sd 12:0:8:0: [sdk] Mode Sense: 73 00 00 08
[962709.493998] sdi: sdi1
[962709.500804] sd 12:0:8:0: [sdk] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[962709.536155] sdj: sdj1
[962709.539886] sd 12:0:6:0: [sdi] Attached SCSI disk
[962709.578379] sd 12:0:7:0: [sdj] Attached SCSI disk
[962709.599128] sdk: sdk1
[962709.644235] sd 12:0:8:0: [sdk] Attached SCSI disk
[962709.680653] XFS (sdi1): Mounting Filesystem
[962709.713874] XFS (sdj1): Mounting Filesystem
[962709.781311] XFS (sdk1): Mounting Filesystem
[962709.897808] XFS (sdj1): Ending clean mount
[962709.900039] XFS (sdi1): Ending clean mount
[962710.068508] XFS (sdk1): Ending clean mount
[982568.461888] usb 1-8: USB disconnect, device number 2
[1004526.404440] 3w-9xxx: scsi0: AEN: INFO (0x04:0x0029): Verify started:unit=0.
[1009302.444936] UDP: short packet: From 27.37.27.218:3218 3944/109 to
192.168.100.6:50058
[1016683.618559] 3w-9xxx: scsi0: AEN: INFO (0x04:0x002B): Verify
completed:unit=0.
[1081238.863526] sd 12:0:8:0: [sdk] Device not ready
[1081238.863530] sd 12:0:8:0: [sdk] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[1081238.863534] sd 12:0:8:0: [sdk] Sense Key : Not Ready [current]
[1081238.863538] sd 12:0:8:0: [sdk] Add. Sense: Logical unit not ready,
initializing command required
[1081238.863543] sd 12:0:8:0: [sdk] CDB: Read(10): 28 00 a7 c5 85 d0 00 00 08 00
[1081238.863552] end_request: I/O error, dev sdk, sector 2814739920
[1081238.863938] sd 12:0:8:0: [sdk] Device not ready
[1081238.863940] sd 12:0:8:0: [sdk] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
[1081238.863944] sd 12:0:8:0: [sdk] Sense Key : Not Ready [current]
[1081238.863948] sd 12:0:8:0: [sdk] Add. Sense: Logical unit not ready,
initializing command required
[1081238.863952] sd 12:0:8:0: [sdk] CDB: Read(10): 28 00 a7 c5 85 d0 00 00 08 00
[1081238.863960] end_request: I/O error, dev sdk, sector 2814739920
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: Intel Corp.
bios_version: BX97520J.86A.2770.2007.0613.1403
board_vendor: Intel Corporation
board_name: D975XBX2
board_version: AAD53350-507
** Loaded modules:
hfsplus
nls_utf8
nls_cp437
vfat
fat
usb_storage
uas
tun
xt_tcpudp
iptable_filter
ip_tables
x_tables
parport_pc
ppdev
lp
parport
autofs4
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
fuse
udf
xfs
ext2
dm_crypt
asc7621
loop
firewire_sbp2
snd_pcm
snd_page_alloc
snd_timer
snd
soundcore
acpi_cpufreq
i2c_i801
mperf
psmouse
processor
button
serio_raw
pcspkr
evdev
iTCO_wdt
i82975x_edac
iTCO_vendor_support
edac_core
coretemp
i2c_core
thermal_sys
ext4
crc16
jbd2
mbcache
dm_mod
raid10
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
xor
async_tx
raid6_pq
raid1
raid0
multipath
linear
md_mod
ses
enclosure
sd_mod
ata_generic
pata_marvell
crc_t10dif
uhci_hcd
ahci
libahci
ata_piix
firewire_ohci
mptsas
scsi_transport_sas
ehci_hcd
firewire_core
crc_itu_t
3w_9xxx
e1000e
mptscsih
mptbase
libata
usbcore
scsi_mod
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82975X Memory Controller Hub
[8086:277c]
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=09 <?>
Kernel driver in use: i82975x_edac
00:01.0 PCI bridge [0604]: Intel Corporation 82975X PCI Express Root Port
[8086:277d] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: 82c00000-82cfffff
Prefetchable memory behind bridge: 0000000080000000-0000000081ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Intel Corporation Device [8086:5842]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4161
Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0
<1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 75.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Link1: Desc: TargetPort=03 TargetComponent=01 AssocRCRB-
LinkType=Config LinkValid+
Addr: 00:03.0 CfgSpace=0000000000018000
Kernel driver in use: pcieport
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port
1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 82b00000-82bfffff
Prefetchable memory behind bridge: 0000000082e00000-0000000082ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency
L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surprise+
Slot #1, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Intel Corporation N10/ICH 7 Family PCI
Express Port 1 [8086:27d0]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI
Express Port 5 [8086:27e0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 82a00000-82afffff
Prefetchable memory behind bridge: 0000000083300000-00000000835fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surprise+
Slot #5, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Intel Corporation 82801GR/GH/GHM (ICH7
Family) PCI Express Port 5 [8086:27e0]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=05 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI
Express Port 6 [8086:27e2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 82900000-829fffff
Prefetchable memory behind bridge: 0000000083100000-00000000832fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+
Surprise+
Slot #6, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: Intel Corporation 82801GR/GH/GHM (ICH7
Family) PCI Express Port 6 [8086:27e2]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=06 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 5080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 5060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 5040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 5020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI
Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at 82d00400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: 82800000-828fffff
Prefetchable memory behind bridge: 0000000082000000-00000000827fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Intel Corporation Device [8086:5842]
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GH (ICH7DH) LPC Interface
Bridge [8086:27b0] (rev 01)
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE
Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 50b0 [size=16]
Kernel driver in use: ata_piix
00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA
Controller [AHCI mode] [8086:27c1] (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation DeskTop Board D975XBX [8086:5842]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 45
Region 0: I/O ports at 50c8 [size=8]
Region 1: I/O ports at 50e4 [size=4]
Region 2: I/O ports at 50c0 [size=8]
Region 3: I/O ports at 50e0 [size=4]
Region 4: I/O ports at 50a0 [size=16]
Region 5: Memory at 82d00000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4189
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller
[8086:27da] (rev 01)
Subsystem: Intel Corporation DeskTop Board D975XBX [8086:5842]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 5000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 RAID bus controller [0104]: 3ware Inc 9650SE SATA-II RAID PCIe
[13c1:1004] (rev 01)
Subsystem: 3ware Inc 9650SE SATA-II RAID PCIe [13c1:1004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 80000000 (64-bit, prefetchable) [size=32M]
Region 2: Memory at 82c00000 (64-bit, non-prefetchable) [size=4K]
Region 4: I/O ports at 4000 [size=256]
Expansion ROM at 82c20000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <128ns,
L1 <2us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency
L0 <512ns, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk-
DLActive+ BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: 3w-9xxx
02:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic SAS1068E
PCI-Express Fusion-MPT SAS [1000:0058] (rev 08)
Subsystem: LSI Logic / Symbios Logic Device [1000:30a0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at 82b10000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at 82b00000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at 82e00000 [disabled] [size=2M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency
L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [98] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: mptsas
03:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE6145 SATA II
PCI-E controller [11ab:6145] (rev a1) (prog-if 8f)
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 2018 [size=8]
Region 1: I/O ports at 2024 [size=4]
Region 2: I/O ports at 2010 [size=8]
Region 3: I/O ports at 2020 [size=4]
Region 4: I/O ports at 2000 [size=16]
Region 5: Memory at 82a00000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at 83300000 [disabled] [size=256K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0
<256ns, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 1f, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: ahci
04:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit Ethernet
Controller [8086:109a]
Subsystem: Intel Corporation Desktop Board D975XBX [8086:30a5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at 82900000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 4199
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM unknown, Latency
L0 <128ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-19-d1-ff-ff-e3-5e-bc
Kernel driver in use: e1000e
05:00.0 VGA compatible controller [0300]: Matrox Electronics Systems Ltd. MGA
2064W [Millennium] [102b:0519] (rev 01) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 82804000 (32-bit, non-prefetchable) [size=16K]
Region 1: Memory at 82000000 (32-bit, prefetchable) [size=8M]
Expansion ROM at 82810000 [disabled] [size=64K]
05:04.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Intel Corporation Device [8086:5842]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 82808000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at 82800000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-3-amd64 (SMP w/2 CPU cores)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.44
ii initramfs-tools [linux-initramfs-tool] 0.106
ii kmod 8-2
ii linux-base 3.5
ii module-init-tools 8-2
Versions of packages linux-image-3.2.0-3-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-3-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-22.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-3-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-3-amd64/postinst/depmod-error-initrd-3.2.0-3-amd64: false
linux-image-3.2.0-3-amd64/prerm/removing-running-kernel-3.2.0-3-amd64: true
linux-image-3.2.0-3-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-3-amd64/postinst/missing-firmware-3.2.0-3-amd64:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
