Package: src
Version: 3.2.20-1
Severity: important
Hi,
the screen turns to black at the beginning of the boot process.
I have to run "setpci -s 00:02.0 F4.B=00" via ssh to see anything.
This is similar to bug 668274.
Booting with the 2.6 kernel does not show this problem.
Best regards
Roland
-- Package-specific info:
** Version:
Linux version 3.2.0-2-amd64 (Debian 3.2.20-1) (debian-ker...@lists.debian.org)
(gcc version 4.6.3 (Debian 4.6.3-7) ) #1 SMP Mon Jun 11 17:24:18 UTC 2012
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-2-amd64 root=/dev/mapper/sda2_crypt ro quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 2204.412078] ehci_hcd 0000:00:1d.7: PCI INT A disabled
[ 2204.976104] PM: suspend of devices complete after 671.660 msecs
[ 2204.992352] ehci_hcd 0000:00:1d.7: PME# enabled
[ 2204.992361] ehci_hcd 0000:00:1d.7: wake-up capability enabled by ACPI
[ 2205.008327] uhci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[ 2205.008803] ehci_hcd 0000:00:1a.7: PME# enabled
[ 2205.008809] ehci_hcd 0000:00:1a.7: wake-up capability enabled by ACPI
[ 2205.024156] uhci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[ 2205.024249] PM: late suspend of devices complete after 48.140 msecs
[ 2205.024392] ACPI: Preparing to enter system sleep state S3
[ 2205.024540] PM: Saving platform NVS memory
[ 2205.026163] Disabling non-boot CPUs ...
[ 2205.128167] CPU 1 is now offline
[ 2205.128773] ACPI: Low-level resume complete
[ 2205.128773] PM: Restoring platform NVS memory
[ 2205.128773] CPU0: Thermal monitoring handled by SMI
[ 2205.128773] Enabling non-boot CPUs ...
[ 2205.128773] Booting Node 0 Processor 1 APIC 0x1
[ 2205.128773] smpboot cpu 1: start_ip = 99000
[ 2205.027732] Calibrating delay loop (skipped) already calibrated this CPU
[ 2205.153608] NMI watchdog enabled, takes one hw-pmu counter.
[ 2205.159549] CPU1 is up
[ 2205.160962] ACPI: Waking up from system sleep state S3
[ 2205.163681] i915 0000:00:02.0: restoring config space at offset 0x6 (was
0xc, writing 0xc000000c)
[ 2205.163688] i915 0000:00:02.0: restoring config space at offset 0x1 (was
0x900007, writing 0x900407)
[ 2205.163743] uhci_hcd 0000:00:1a.0: restoring config space at offset 0x1 (was
0x2900005, writing 0x2900001)
[ 2205.163772] uhci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[ 2205.163811] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was
0x2900006, writing 0x2900002)
[ 2205.163831] ehci_hcd 0000:00:1a.7: wake-up capability disabled by ACPI
[ 2205.163837] ehci_hcd 0000:00:1a.7: PME# disabled
[ 2205.163856] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf
(was 0x100, writing 0x10b)
[ 2205.163877] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3
(was 0x0, writing 0x10)
[ 2205.163883] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1
(was 0x100006, writing 0x100002)
[ 2205.163915] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was
0x100, writing 0x10b)
[ 2205.163927] pcieport 0000:00:1c.0: restoring config space at offset 0x9 (was
0x10001, writing 0xd131d041)
[ 2205.163932] pcieport 0000:00:1c.0: restoring config space at offset 0x8 (was
0x0, writing 0xd660d570)
[ 2205.163946] pcieport 0000:00:1c.0: restoring config space at offset 0x1 (was
0x100001, writing 0x100407)
[ 2205.163996] pcieport 0000:00:1c.1: restoring config space at offset 0xf (was
0x200, writing 0x20b)
[ 2205.164030] pcieport 0000:00:1c.1: restoring config space at offset 0x9 (was
0x10001, writing 0xd231d141)
[ 2205.164036] pcieport 0000:00:1c.1: restoring config space at offset 0x8 (was
0x0, writing 0xd560d460)
[ 2205.164051] pcieport 0000:00:1c.1: restoring config space at offset 0x1 (was
0x100007, writing 0x100407)
[ 2205.164102] pcieport 0000:00:1c.2: restoring config space at offset 0xf (was
0x300, writing 0x30b)
[ 2205.164114] pcieport 0000:00:1c.2: restoring config space at offset 0x9 (was
0x10001, writing 0xd331d241)
[ 2205.164119] pcieport 0000:00:1c.2: restoring config space at offset 0x8 (was
0x0, writing 0xd450d350)
[ 2205.164133] pcieport 0000:00:1c.2: restoring config space at offset 0x1 (was
0x100007, writing 0x100407)
[ 2205.164195] uhci_hcd 0000:00:1d.0: restoring config space at offset 0x1 (was
0x2900005, writing 0x2900001)
[ 2205.164222] uhci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[ 2205.164253] uhci_hcd 0000:00:1d.1: restoring config space at offset 0x1 (was
0x2900005, writing 0x2900001)
[ 2205.164291] uhci_hcd 0000:00:1d.2: restoring config space at offset 0x1 (was
0x2900005, writing 0x2900001)
[ 2205.164330] uhci_hcd 0000:00:1d.3: restoring config space at offset 0x1 (was
0x2900005, writing 0x2900001)
[ 2205.164376] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was
0x2900006, writing 0x2900002)
[ 2205.164396] ehci_hcd 0000:00:1d.7: wake-up capability disabled by ACPI
[ 2205.164401] ehci_hcd 0000:00:1d.7: PME# disabled
[ 2205.164421] pci 0000:00:1e.0: restoring config space at offset 0x9 (was
0x10001, writing 0x1fff1)
[ 2205.164426] pci 0000:00:1e.0: restoring config space at offset 0x8 (was 0x0,
writing 0xfff0)
[ 2205.164431] pci 0000:00:1e.0: restoring config space at offset 0x7 (was
0x22800000, writing 0x228000f0)
[ 2205.164444] pci 0000:00:1e.0: restoring config space at offset 0x1 (was
0x100000, writing 0x100007)
[ 2205.164536] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was
0x2b00007, writing 0x2b00407)
[ 2205.165195] PM: early resume of devices complete after 1.589 msecs
[ 2205.165303] i915 0000:00:02.0: setting latency timer to 64
[ 2205.165455] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2205.165527] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2205.165594] usb usb3: root hub lost power or was reset
[ 2205.165696] ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 21 (level, low) -> IRQ 21
[ 2205.165702] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2205.165734] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) ->
IRQ 22
[ 2205.165741] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 2205.165792] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 2205.165840] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2205.165846] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2205.165873] usb usb4: root hub lost power or was reset
[ 2205.165885] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2205.165892] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2205.165918] usb usb5: root hub lost power or was reset
[ 2205.165930] uhci_hcd 0000:00:1d.2: PCI INT D -> GSI 20 (level, low) -> IRQ 20
[ 2205.165936] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2205.165963] usb usb6: root hub lost power or was reset
[ 2205.165975] uhci_hcd 0000:00:1d.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2205.165982] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 2205.166008] usb usb7: root hub lost power or was reset
[ 2205.166022] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2205.166029] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2205.166053] pci 0000:00:1e.0: setting latency timer to 64
[ 2205.166068] ahci 0000:00:1f.2: setting latency timer to 64
[ 2205.166315] b43-pci-bridge 0000:04:00.0: PCI INT A -> GSI 17 (level, low) ->
IRQ 17
[ 2205.167052] sd 0:0:0:0: [sda] Starting disk
[ 2205.252567] atl1c 0000:05:00.0: irq 46 for MSI/MSI-X
[ 2205.500087] ata5: SATA link down (SStatus 0 SControl 300)
[ 2205.648061] usb 4-1: reset low-speed USB device number 3 using uhci_hcd
[ 2205.664059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2205.667800] ata2.00: configured for UDMA/100
[ 2206.885565] atl1c 0000:05:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full
Duplex>
[ 2208.456083] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2208.500351] ata1.00: configured for UDMA/133
[ 2208.716283] b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
[ 2214.245367] PM: resume of devices complete after 9080.106 msecs
[ 2214.245664] PM: Finishing wakeup.
[ 2214.245666] Restarting tasks ... done.
[ 2214.860237] video LNXVIDEO:01: Restoring backlight state
[ 2228.128052] eth0: no IPv6 routers present
** Model information
sys_vendor: eMachines
product_name: eMachines G725
product_version: V3.06
chassis_vendor: eMachines
chassis_version: V3.06
bios_vendor: eMachines
bios_version: V3.06
board_vendor: eMachines
board_name: eMachines G725
board_version: V3.06
** Loaded modules:
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
acpi_cpufreq
mperf
cpufreq_stats
cpufreq_userspace
cpufreq_powersave
cpufreq_conservative
parport_pc
ppdev
lp
parport
bnep
rfcomm
bluetooth
crc16
binfmt_misc
uinput
fuse
ext3
mbcache
jbd
loop
snd_hda_codec_realtek
joydev
arc4
b43
snd_hda_intel
snd_hda_codec
i915
snd_hwdep
snd_pcm
bcma
snd_page_alloc
drm_kms_helper
psmouse
i2c_i801
mac80211
drm
cfg80211
snd_seq
snd_seq_device
snd_timer
acer_wmi
iTCO_wdt
sparse_keymap
rfkill
rng_core
i2c_algo_bit
pcspkr
serio_raw
iTCO_vendor_support
snd
i2c_core
evdev
mxm_wmi
battery
ac
soundcore
wmi
power_supply
video
processor
button
xfs
sha256_generic
cryptd
aes_x86_64
aes_generic
cbc
dm_crypt
dm_mod
sd_mod
sr_mod
cdrom
crc_t10dif
usbhid
hid
ahci
libahci
ssb
mmc_core
uhci_hcd
libata
atl1c
pcmcia
thermal
pcmcia_core
thermal_sys
ehci_hcd
usbcore
scsi_mod
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory
Controller Hub [8086:2a40] (rev 09)
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series
Chipset Integrated Graphics Controller [8086:2a42] (rev 09) (prog-if 00 [VGA
controller])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 50f0 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset
Integrated Graphics Controller [8086:2a43] (rev 09)
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d3400000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 [8086:2937] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 50c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 [8086:293c] (rev 03) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 21
Region 0: Memory at d6704c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio
Controller [8086:293e] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at d6700000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 1 [8086:2940] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d5700000-d66fffff
Prefetchable memory behind bridge: 00000000d0400000-00000000d13fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 2 [8086:2942] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d4600000-d56fffff
Prefetchable memory behind bridge: 00000000d1400000-00000000d23fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 3 [8086:2944] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00001000-00002fff
Memory behind bridge: d3500000-d45fffff
Prefetchable memory behind bridge: 00000000d2400000-00000000d33fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 [8086:2934] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 50a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 [8086:2935] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 5080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 [8086:2936] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at 5060 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 [8086:2939] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 5040 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 [8086:293a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d6704800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller
[8086:2919] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E)
4 port SATA Controller [AHCI mode] [8086:2929] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 43
Region 0: I/O ports at 50e8 [size=8]
Region 1: I/O ports at 50fc [size=4]
Region 2: I/O ports at 50e0 [size=8]
Region 3: I/O ports at 50f8 [size=4]
Region 4: I/O ports at 5020 [size=32]
Region 5: Memory at d6704000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller
[8086:2930] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at d6705000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 5000 [size=32]
Kernel driver in use: i801_smbus
04:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g
LP-PHY [14e4:4315] (rev 01)
Subsystem: Foxconn International, Inc. T77H106.00 Wireless Half-size
Mini PCIe Card [105b:e01b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d4600000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
05:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8132 Fast
Ethernet [1969:1062] (rev c0)
Subsystem: Acer Incorporated [ALI] Device [1025:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 46
Region 0: Memory at d3500000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 1000 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 003: ID 046d:c05a Logitech, Inc. Optical Mouse M90
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.44
ii initramfs-tools [linux-initramfs-tool] 0.106
ii kmod 8-2
ii linux-base 3.5
ii module-init-tools 8-2
Versions of packages linux-image-3.2.0-2-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-2-amd64 suggests:
ii grub-pc 1.99-22.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-2-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.36
ii firmware-linux-nonfree 0.36
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.36
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-2-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-2-amd64/postinst/depmod-error-initrd-3.2.0-2-amd64: false
* linux-image-3.2.0-2-amd64/postinst/missing-firmware-3.2.0-2-amd64:
linux-image-3.2.0-2-amd64/prerm/removing-running-kernel-3.2.0-2-amd64: true
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
