Package: installation-reports
Boot method: Network
Image version: 17-05-2006 www.debian.org (amd64 daily snapshot)
Date: 17-05-2006 20:00 CET
Machine: Noname
Processor: AMD Athlon 64 3200+
Memory: 1 GB
Partitions:
Output of lspci and lspci -n:
lspci
0000:00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev
a3)
0000:00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
0000:00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
0000:00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
0000:00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2)
0000:00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev
f3)
0000:00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev
f3)
0000:00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
0000:00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
0000:00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
0000:01:08.0 Network controller: RaLink Ralink RT2500 802.11 Cardbus Reference
Card (rev 01)
0000:01:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 46)
0000:01:0d.0 Multimedia audio controller: Creative Labs SB Audigy LS
0000:02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 Gigabit
Ethernet Controller (rev 15)
0000:03:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA
Raid II Controller (rev 01)
0000:05:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600
GT] (rev a2)
lspci -n
0000:00:00.0 0580: 10de:005e (rev a3)
0000:00:01.0 0601: 10de:0050 (rev a3)
0000:00:01.1 0c05: 10de:0052 (rev a2)
0000:00:02.0 0c03: 10de:005a (rev a2)
0000:00:02.1 0c03: 10de:005b (rev a3)
0000:00:06.0 0101: 10de:0053 (rev f2)
0000:00:07.0 0101: 10de:0054 (rev f3)
0000:00:08.0 0101: 10de:0055 (rev f3)
0000:00:09.0 0604: 10de:005c (rev a2)
0000:00:0a.0 0680: 10de:0057 (rev a3)
0000:00:0b.0 0604: 10de:005d (rev a3)
0000:00:0c.0 0604: 10de:005d (rev a3)
0000:00:0d.0 0604: 10de:005d (rev a3)
0000:00:0e.0 0604: 10de:005d (rev a3)
0000:00:18.0 0600: 1022:1100
0000:00:18.1 0600: 1022:1101
0000:00:18.2 0600: 1022:1102
0000:00:18.3 0600: 1022:1103
0000:01:08.0 0280: 1814:0201 (rev 01)
0000:01:0c.0 0c00: 1106:3044 (rev 46)
0000:01:0d.0 0401: 1102:0007
0000:02:00.0 0200: 11ab:4362 (rev 15)
0000:03:00.0 0180: 1095:3132 (rev 01)
0000:05:00.0 0300: 10de:0140 (rev a2)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [E]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
Comments/Problems:
Could not manually perform partitioning. I could see only /dev/sda as a
whole disk but no partitions. I could create new partitions, but the old
ones were not visible! I could not afford going from scratch while other
OS was installed.
Please see attached dmesg output. I tried to erase one partition, but did
not help
Kind regards,
Bohdan
ered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI wakeup devices:
HUB0 XVR0 XVR1 XVR2 XVR3 USB0 USB2 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 148k freed
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) ->
IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 16, io mem 0xfe02f000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
pnp: the driver 'parport_pc' has been registered
pnp: match found with the PnP device '00:07' and the driver 'parport_pc'
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 22 (level, low) ->
IRQ 17
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: irq 17, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
libata version 1.20 loaded.
sata_nv 0000:00:07.0: version 0.8
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 21 (level, low) ->
IRQ 18
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xF600 irq 18
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xF608 irq 18
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfb08-0xfb0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 488397168 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
ohci_hcd 0000:00:02.0: wakeup
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
Vendor: ATA Model: ST3250823AS Rev: 3.03
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 20 (level, low) ->
IRQ 19
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xF100 irq 19
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xF108 irq 19
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
usb 1-1: new low speed USB device using ohci_hcd and address 2
ata3: no device found (phy stat 00000000)
scsi2 : sata_nv
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (22 C)
ata4: no device found (phy stat 00000000)
scsi3 : sata_nv
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda:ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
sda1 sda2 < sda5 sda6 sda7 sda8 > sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
vga16fb: initializing
vga16fb: mapped to 0xffff8100000a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
usb 1-5: new full speed USB device using ohci_hcd and address 3
input: Logitech USB Receiver as /class/input/input0
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
ohci1394: $Rev: 1313 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 20 sharing vector 0xD1 and IRQ 20
ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [APC4] -> GSI 19 (level, low) ->
IRQ 20
PCI: Via IRQ fixup for 0000:01:0c.0, from 5 to 4
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20] MMIO=[fdeff000-fdeff7ff]
Max Packet=[2048]
sata_sil24 0000:03:00.0: version 0.23
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
GSI 21 sharing vector 0xD9 and IRQ 21
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC1] -> GSI 16 (level, low) ->
IRQ 21
PCI: Setting latency timer of device 0000:03:00.0 to 64
ata5: SATA max UDMA/100 cmd 0xFFFFC20000070000 ctl 0x0 bmdma 0x0 irq 21
ata6: SATA max UDMA/100 cmd 0xFFFFC20000072000 ctl 0x0 bmdma 0x0 irq 21
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata5: no device found (phy stat 00000000)
scsi4 : sata_sil24
ata6: no device found (phy stat 00000000)
scsi5 : sata_sil24
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00007ce819]
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
floppy0: no floppy controllers found
Probing IDE interface ide1...
sbp2: $Rev: 1306 $ Ben Collins <[EMAIL PROTECTED]>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) ->
IRQ 16
PCI: Setting latency timer of device 0000:00:0a.0 to 64
eth1394: $Rev: 1312 $ Ben Collins <[EMAIL PROTECTED]>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1: forcedeth.c: subsystem: 01462:7100 bound to 0000:00:0a.0
floppy0: no floppy controllers found
floppy0: no floppy controllers found
program parted_devices is using a deprecated SCSI ioctl, please convert it to
SG_IO
JFS: nTxBlock = 8015, nTxLock = 64121
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no
debug enabled
SGI XFS Quota Management subsystem
program parted_devices is using a deprecated SCSI ioctl, please convert it to
SG_IO
program parted_server is using a deprecated SCSI ioctl, please convert it to
SG_IO
EXT2-fs warning (device sda8): ext2_fill_super: mounting ext3 filesystem as ext2
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 > sda3 sda4
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 > sda3 sda4
program parted_devices is using a deprecated SCSI ioctl, please convert it to
SG_IO
program parted_server is using a deprecated SCSI ioctl, please convert it to
SG_IO
EXT2-fs warning (device sda7): ext2_fill_super: mounting ext3 filesystem as ext2
