Package: installation-reports Boot method: Boot from netinst install CD Image version: Debian etch installation CD-ROM, built 20060409 Date: Mon Apr 17 08:55:00 GMT/BST 2006
Machine: Fujitsu LifeBook P7120 Notebook Processor: Intel Pentium M Processor ULV 753 (1.2 GHz, 2M L2 Cache) Memory: 1 GB Partitions: <df -Tl will do; the raw partition table is preferred> Disk /dev/hda: 60.0 GB, 60011642880 bytes 255 heads, 63 sectors/track, 7296 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 1 1306 10490413+ 7 HPFS/NTFS (original XP) /dev/hda2 1307 2522 9767520 83 Linux (ubuntu 5.04) /dev/hda3 * 2523 3738 9767520 83 Linux (ubuntu 5.10) /dev/hda4 3739 5319 12699382+ 5 Extended /dev/hda5 3739 4103 2931831 82 Linux swap / Solaris /dev/hda6 4104 5319 9767488+ 83 Linux (debian Etch) Output of lspci and lspci -n: 0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04) 0000:00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04) 0000:00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04) 0000:00:1b.0 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 04) 0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04) 0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04) 0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04) 0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04) 0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04) 0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4) 0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04) 0000:00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04) 0000:00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04) 0000:00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04) 0000:06:03.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3) 0000:06:03.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08) 0000:06:03.2 0805: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17) 0000:06:03.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 08) 0000:06:03.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 03) 0000:06:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 0000:06:05.0 Network controller: Intel Corporation PRO/Wireless 2915ABG MiniPCI Adapter (rev 05) 0000:00:00.0 0600: 8086:2590 (rev 04) 0000:00:02.0 0300: 8086:2592 (rev 04) 0000:00:02.1 0380: 8086:2792 (rev 04) 0000:00:1b.0 0403: 8086:2668 (rev 04) 0000:00:1d.0 0c03: 8086:2658 (rev 04) 0000:00:1d.1 0c03: 8086:2659 (rev 04) 0000:00:1d.2 0c03: 8086:265a (rev 04) 0000:00:1d.3 0c03: 8086:265b (rev 04) 0000:00:1d.7 0c03: 8086:265c (rev 04) 0000:00:1e.0 0604: 8086:2448 (rev d4) 0000:00:1f.0 0601: 8086:2641 (rev 04) 0000:00:1f.1 0101: 8086:266f (rev 04) 0000:00:1f.2 0101: 8086:2653 (rev 04) 0000:00:1f.3 0c05: 8086:266a (rev 04) 0000:06:03.0 0607: 1180:0476 (rev b3) 0000:06:03.1 0c00: 1180:0552 (rev 08) 0000:06:03.2 0805: 1180:0822 (rev 17) 0000:06:03.3 0880: 1180:0592 (rev 08) 0000:06:03.4 0880: 1180:0852 (rev 03) 0000:06:04.0 0200: 10ec:8139 (rev 10) 0000:06:05.0 0280: 8086:4223 (rev 05) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [E] Config network: [E] Detect CD: [E] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [E] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: Initial attempt to install using Etch Beta 2 Install image failed to detect the SATA DVD-RAM drive, even following the workaround instructions at http://wiki.debian.org/DebianInstaller/SataAtapiHowto Switching to the latest daily build and following the relevent workaround instructions at the above URL resulted in the DVD-RAM media being found. Install then proceeded to the 'detect network hardare' stage, where Debian found: eth0: Ethernet or Fast Ethernet eth1: Realtek semiconductor co., Ltd. RTL-8139/8139C/8139C+ The first entry corresponds to a wireless interface which I had been successfully using for Lan access from Ubuntu. The Ubuntu detect lists: eth0: Realtek semiconductor co., Ltd. RTL-8139/8139C/8139C+ eth1: Intel corp. 4223 (wireless) which clearly recognises the Intel Wireless hardware and prompts for SSID/mode etc. Debian did not, and failed both DHCP and manual config attempts. The Realtek device is a 10/100 UTP interface, which was connected to a 10Mb hub, which failed to work also. It was not till I connected to a 10/100Mb hub that the network started to work for the Debian install, so I suspect it was not supporting the 10Mb mode properly. The last problem I encountered was with the disk partitioner, which failed to list any of the partitions on the hard disk, leaving no option other than to reformat the entire disk. This I suspect was caused by the fact that the order of the partitions in the table was not the same as the order on disk. I had used a tool called 'osselector' to shrink the Windows XP partition and create, and in installing itself and making partitions seemed to produce something that confused the debian partitioner. The problem was resolved by deleting all partitions except for the first three 'primary' partitions, which were contiguous and sequential. After this, the installation completed. Post installation checked showed that my wireless i/f was not detected (worked find in ubuntu), the DVD-RAM was not detected (libata.atapi_enabled=1 no longer recognised), and the X server was not working - failing with Fatal server error: could not optn default font 'fixed'; The generated Xorg.conf file also referenced 'vesa' drivers rather than the i810 - which I think does not fully utilise the hardware capabilitys. I have not yet tried reconfiguring the kernel. Copy of dmesg output follows: >Linux version 2.6.15-1-686 (Debian 2.6.15-8) ([EMAIL PROTECTED]) (gcc version >4.0.3 20060212 (prerelease) (Debian 4.0.2-9)) #2 Mon Mar 6 15:27:08 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003f670000 (usable) BIOS-e820: 000000003f670000 - 000000003f683000 (ACPI data) BIOS-e820: 000000003f683000 - 000000003f700000 (ACPI NVS) BIOS-e820: 000000003f700000 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0010000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) 118MB HIGHMEM available. 896MB LOWMEM available. On node 0 totalpages: 259696 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 30320 pages, LIFO batch:7 DMI 2.3 present. ACPI: RSDP (v000 FUJ ) @ 0x000f5880 ACPI: RSDT (v001 FUJ FJNB1A5 0x01120000 FUJ 0x00000100) @ 0x3f67c448 ACPI: FADT (v001 FUJ FJNB1A5 0x01120000 FUJ 0x00000100) @ 0x3f682f8c ACPI: MADT (v001 FUJ FJNB1A5 0x01120000 FUJ 0x00000100) @ 0x3f6828ad ACPI: SSDT (v001 FUJ FJNB1A5 0x01120000 INTL 0x20030522) @ 0x3f682907 ACPI: SSDT (v001 FUJ FJNB1A5 0x01120000 INTL 0x20030522) @ 0x3f682d4c ACPI: MCFG (v001 FUJ FJNB1A5 0x01120000 FUJ 0x00000100) @ 0x3f682f28 ACPI: BOOT (v001 FUJ FJNB1A5 0x01120000 FUJ 0x00000100) @ 0x3f682f64 ACPI: DSDT (v001 FUJ FJNB1A5 0x01120000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:13 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Built 1 zonelists Kernel command line: root=/dev/hda6 ro libata.atapi_enabled=1 Unknown boot option `libata.atapi_enabled=1': ignoring mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 1197.595 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1022044k/1038784k available (1425k kernel code, 15920k reserved, 530k data, 144k init, 121280k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2397.30 BogoMIPS (lpj=1198652) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) CPU: Intel(R) Pentium(R) M processor 1.20GHz stepping 08 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking if image is initramfs... it is Freeing initrd memory: 4574k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd882, last bus=7 PCI: Using MMCONFIG ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:02.0 PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH6 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 PCI: Bus 7, cardbus bridge: 0000:06:03.0 IO window: 00002400-000024ff IO window: 00002800-000028ff PREFETCH window: 50000000-51ffffff MEM window: 54000000-55ffffff PCI: Bridge: 0000:00:1e.0 IO window: 2000-2fff MEM window: b0100000-b01fffff PREFETCH window: 50000000-51ffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 169 Simple Boot Flag at 0x7f set to 0x1 audit: initializing netlink socket (disabled) audit(1145368878.289:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Using IPI Shortcut mode ACPI wakeup devices: PCIB MODM AZAL LID ACPI: (supports S0 S3 S4 S5) Freeing unused kernel memory: 144k freed ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) input: AT Translated Set 2 keyboard as /class/input/input0 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 177, io base 0x00001420 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 185, io base 0x00001440 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ieee1394: Initialized config rom entry `ip1394' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 193, io base 0x00001460 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 169, io base 0x00001480 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: irq 177, io mem 0xb0004000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected ohci1394: $Rev: 1313 $ Ben Collins <[EMAIL PROTECTED]> ACPI: PCI Interrupt 0000:06:03.1[B] -> GSI 17 (level, low) -> IRQ 201 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[201] MMIO=[b0100000-b01007ff] Max Packet=[2048] ICH6: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 193 ICH6: chipset revision 4 ICH6: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1410-0x1417, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... SCSI subsystem initialized libata version 1.20 loaded. hda: TOSHIBA MK6006GAH, ATA DISK drive usb 3-1: new full speed USB device using uhci_hcd and address 2 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 8139cp: pci dev 0000:06:04.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip 8139cp: Try the "8139too" driver instead. 8139too Fast Ethernet driver 0.9.27 ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 20 (level, low) -> IRQ 209 eth0: RealTek RTL8139 at 0x2000, 00:0b:5d:96:c6:d5, IRQ 209 eth0: Identified 8139 chip type 'RTL-8100B/8139D' hda: max request size: 1024KiB ahci 0000:00:1f.2: version 1.2 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 185 hda: 117210240 sectors (60011 MB), CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 < hda5 hda6 > usb 4-2: new full speed USB device using uhci_hcd and address 2 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000e100382e8fd] PCI: Setting latency timer of device 0000:00:1f.2 to 64 ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl IDE mode ahci 0000:00:1f.2: flags: 64bit stag led pmp ata1: SATA max UDMA/133 cmd 0xF887C500 ctl 0x0 bmdma 0x0 irq 185 ata2: SATA max UDMA/133 cmd 0xF887C580 ctl 0x0 bmdma 0x0 irq 185 ata3: SATA max UDMA/133 cmd 0xF887C600 ctl 0x0 bmdma 0x0 irq 185 ata4: SATA max UDMA/133 cmd 0xF887C680 ctl 0x0 bmdma 0x0 irq 185 ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0007 ata1: dev 0 ATAPI, max UDMA/33 ata1(0): applying bridge limits ata1: dev 0 configured for UDMA/33 scsi0 : ahci ata2: no device found (phy stat 00000000) scsi1 : ahci ata3: no device found (phy stat 00000000) scsi2 : ahci ata4: no device found (phy stat 00000000) scsi3 : ahci ata1(0): WARNING: ATAPI is disabled, device ignored. Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. input: PC Speaker as /class/input/input1 hw_random: RNG not detected Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 915GM Chipset. agpgart: Detected 7932K stolen memory. agpgart: AGP aperture is 256M @ 0xc0000000 Bluetooth: Core ver 2.8 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: HCI USB driver ver 2.9 mice: PS/2 mouse device common for all mice usbcore: registered new driver hci_usb Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x202000 input: SynPS/2 Synaptics TouchPad as /class/input/input2 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1b.0 to 64 ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 169 Yenta: CardBus bridge found at 0000:06:03.0 [10cf:1254] Real Time Clock Driver v1.12 Yenta: ISA IRQ mask 0x04b8, PCI irq 169 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff cs: IO port probe 0x2000-0x2fff: clean. pcmcia: parent PCI bridge Memory window: 0xb0100000 - 0xb01fffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.7 ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]> eth1394: $Rev: 1312 $ Ben Collins <[EMAIL PROTECTED]> eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.0.8 ipw2200: Copyright(c) 2003-2005 Intel Corporation ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 18 (level, low) -> IRQ 193 ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. ipw2200: ipw-2.4-boot.fw load failed: Reason -2 ipw2200: Unable to load firmware: -2 ipw2200: failed to register network device ACPI: PCI interrupt for device 0000:06:05.0 disabled ipw2200: probe of 0000:06:05.0 failed with error -5 Adding 2931820k swap on /dev/hda5. Priority:-1 extents:1 across:2931820k EXT3 FS on hda6, internal journal pcmcia: Detected deprecated PCMCIA ioctl usage. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. hw_random: RNG not detected eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 ACPI: Battery Slot [CMB1] (battery present) ACPI: Battery Slot [CMB2] (battery absent) ACPI: AC Adapter [AC] (on-line) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Power Button (CM) [PWRB] Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver eth0: no IPv6 routers present -- Digby R. S. Tarvin digbyt(at)digbyt.com http://www.digbyt.com -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
