TG3 NIC autodetection fails with Supermicro P8SCI server motherboard

[Pasi Kärkkäinen]

Hi!

I just installed sarge/testing with network installation CD from 27-12-2004. I 
used
"linux26" kernel.

NIC autodetection did not detect onboard tg3 NIC's. But when I chose tg3
from the "manual driver selection" list, the NIC was detected OK.

Output of lspci for Supermicro P8SCI server motherboard:

0000:04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 
Gigabit Ethernet PCI Express (rev 11)
        Subsystem: Super Micro Computer Inc: Unknown device 02c6
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr-Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-<TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 0x08 (32 bytes)
        Interrupt: pin A routed to IRQ 169
        Region 0: Memory at d0100000 (64-bit, non-prefetchable) [size=64K]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- 
AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
        Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3Enable-
                Address: 0053089d82ff4ff8  Data: befc
        Capabilities: [d0] #10 [0001]

0000:05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 
Gigabit Ethernet PCI Express (rev 11)
        Subsystem: Super Micro Computer Inc: Unknown device 02c6
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr-Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-<TAbort- 
<MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 0x08 (32 bytes)
        Interrupt: pin A routed to IRQ 177
        Region 0: Memory at d0200000 (64-bit, non-prefetchable) [size=64K]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- 
AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
        Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3Enable-
                Address: a31f7f0b9df77bf8  Data: fff4
        Capabilities: [d0] #10 [0001]


If you have any questions, please CC to me, I'm not subscribed to the list..

Thanks.

-- Pasi Kärkkäinen
       
                                   ^
                                .     .
                                 Linux
                              /    -    \
                             Choice.of.the
                           .Next.Generation.


-- 
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]