Package: installation-reports Debian-installer-version: 07 Oct 2004 - http://cdimage.debian.org/pub/cdimage-testing/sid_d-i/i386/pre-rc2/sarge -i386-netinst.iso uname -a: Linux aap 2.6.8-1-686 Date: 07 Oct 2004 - 11am~12am CET Method: boot of cd with netinst base, using authentication through squid proxy Machine: Dell PowerEdge 2550 Processor: Dual Pentium 3 1000Mhz Coppermine Memory: 3Gb Root Device: Scsi, PERC 3/Di Raid controller Root Size/partition table: /dev/sda1 * 1 122 979933+ 83 Linux <-- root /dev/sda2 123 4425 34563847+ 5 Extended /dev/sda5 123 244 979933+ 83 Linux /dev/sda6 245 609 2931831 83 Linux /dev/sda7 610 4317 29784478+ 83 Linux /dev/sda8 4318 4425 867478+ 82 Linux swap Output of lspci and lspci -n: 0000:00:00.0 Host bridge: ServerWorks CNB20HE Host Bridge (rev 23) 0000:00:00.1 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01) 0000:00:00.2 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01) 0000:00:00.3 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01) 0000:00:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 0000:00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 50) 0000:00:0f.1 IDE interface: ServerWorks OSB4 IDE Controller 0000:00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 04) 0000:01:08.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5700 Gigabit Ethernet (rev 12) 0000:02:02.0 PCI bridge: Intel Corp. 80960RM [i960RM Bridge] (rev 01) 0000:02:02.1 RAID bus controller: Dell PowerEdge Expandable RAID Controller 3/Di (rev 01) 0000:02:04.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) 0000:00:00.0 0600: 1166:0008 (rev 23) 0000:00:00.1 0600: 1166:0008 (rev 01) 0000:00:00.2 0600: 1166:0006 (rev 01) 0000:00:00.3 0600: 1166:0006 (rev 01) 0000:00:0e.0 0300: 1002:4752 (rev 27) 0000:00:0f.0 0601: 1166:0200 (rev 50) 0000:00:0f.1 0101: 1166:0211 0000:00:0f.2 0c03: 1166:0220 (rev 04) 0000:01:08.0 0200: 14e4:1644 (rev 12) 0000:02:02.0 0604: 8086:0962 (rev 01) 0000:02:02.1 0104: 1028:0002 (rev 01) 0000:02:04.0 0200: 8086:1229 (rev 08) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [E] Reboot: [O] Comments/Problems: Grub failed to install. VC/3 reports that it's probing devices and then reported "file /boot/grub/stage1 not read correctly." Lilo installed fine -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
