Package: installation-reports
INSTALL REPORT
Debian-installer-version: 1 aug 2004, cdimage.debian.org
uname -a: Linux rebeka 2.6.5-my1 #2 Fri Apr 30 13:34:44 CEST 2004 i686
GNU/Linux
Date: 14 sep 2004, 0:10
Method: hdimage from USB flash disk
Machine: ordinary rackmounted PC server
Processor: Celeron 1800
Memory: 1024
Root Device: IDE, /dev/md0
Root Size/partition table:
/dev/md/0 on / type xfs (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
tmpfs on /dev/shm type tmpfs (rw)
Output of lspci and lspci -n:
0000:00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host
Bridge (rev 11)
0000:00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP
Bridge (rev 11)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 05)
0000:00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
0000:00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05)
0000:00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 05)
0000:00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
0000:00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 05)
0000:02:0c.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100]
(rev 0d)
0000:02:0d.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100]
(rev 0d)
0000:02:0f.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev
27)
0000:00:00.0 0600: 8086:1a30 (rev 11)
0000:00:01.0 0604: 8086:1a31 (rev 11)
0000:00:1e.0 0604: 8086:244e (rev 05)
0000:00:1f.0 0601: 8086:2440 (rev 05)
0000:00:1f.1 0101: 8086:244b (rev 05)
0000:00:1f.2 0c03: 8086:2442 (rev 05)
0000:00:1f.3 0c05: 8086:2443 (rev 05)
0000:00:1f.4 0c03: 8086:2444 (rev 05)
0000:02:0c.0 0200: 8086:1229 (rev 0d)
0000:02:0d.0 0200: 8086:1229 (rev 0d)
0000:02:0f.0 0300: 1002:4752 (rev 27)
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [ ]
Load installer modules: [E]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [E]
Install boot loader: [E]
Reboot: [O]
Comments/Problems:
On the destination disk, beside the USB boot device, I also had older
version of install ISO.
The installer took the ISO from the disk in precedence before trying to
load it from my USB flash disk.
That resulted in impossibility to load modules and detect hardware
(including network devices).
Firstly I was trying to install directly to an /dev/md0, which installer
set up correctly. Also
XFS creation produced no error. ButInstall base system hung up. After
some tries I finnaly got
to a boot loader installation, I chose GRUB, but another unrecoverable
hung occured.
Finnaly I had to install the system to a small (2 GiB) partition, using
ext2, without trying to setup
software RAID, and using LILO as boot loader. Then I set up /dev/md0,
copied system, installed
GRUB and changed the 2 GiB partition type to swap.
Install logs and other status info is available in
/var/log/debian-installer/.
Once you have filled out this report, mail it to [EMAIL PROTECTED]
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
