Package: installation-reports Debian-installer-version: daily build 15.7.2004 http://www.debian.org/devel/debian-installer
Date: 16.7.2004 8:00 pm CET Method: CD-Image (110 MB, i386 version) Machine: Compaq Armada 3500 Processor:Pentium II - 366 MHz cat /proc/cpuinfo shows processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 6 model name : Mobile Pentium II stepping : 10 cpu MHz : 366.682 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr bogomips : 732.36 Memory: 128 MB Root Device: IDE Harddisk Name: TOSHIBA MK1214GAP Capacity: 12 GB Root Size/partition table: /dev/hda2 1.1 GB uname -a: Linux debiantst.localdomain.fake 2.4.26-1-386 #2 Sat May 1 16:31:24 EST 2004 i686 GNU/Linux Output of lspci: 0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 03) 0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 0000:00:08.0 VGA compatible controller: Chips and Technologies F69000 HiQVideo (rev 64) 0000:00:11.0 CardBus bridge: Texas Instruments PCI1220 (rev 02) 0000:00:11.1 CardBus bridge: Texas Instruments PCI1220 (rev 02) Base System Installation Checklist: Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [0] Install base system: [0] Install boot loader: [O] Reboot: [O] [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Comments/Problems: Installation: - Selected German during the installation and found that the languages in the screen where the keyboard layout is choosen are not sorted alphabetical. I compared this to an installation run with English as language choice and found the same there. As the other language choices are alphabetically sorted this should be the case for this screen too. - Harddisk partitioning: In some cases the paritionsize is incorrectly set. Example: I choose 1.2 GB and a 1.1 GB parition was created (same happened with 2.0 -> 1.9 and 5 -> 4.9 GB) but not when I chose 1.3 GB. - The german screen that is displayed during the time configuration has an issue. When the configuration is run the first time it displays the time with an "UTC" at the end, though at this stage the question if the hardware clock is run on UTC or not is not yet answered. (When I run the installation in English the screen is ok and just shows the time with PM or AM) - After adding an apt-source almost at the end of the installation the "Debian Software Selection"-screen is displayed in English again, though the rest of the installation runs fine in German. - If the final configuration (time configuration, password choice etc.) is not finished and the machine is restarted (for example after the choice of the root password) the configuration of the time zone is run again, though the answer was given before. Kind regards Thorsten -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
