Package: installation-reports Debian-installer-version: beta 4, i386-netinst.iso dowloaded May, 18th, 2004 Date: May, 28th, 2004 Method: booted from netinst.iso image burned on CD-R
Machine: PC with Intel D875PBZ Motherboard Processor: Intel Pentium IV 2.6 GHz Memory: 1024 MB DDR400 Root Device: IDE, /dev/hda9 Root Size: 38 GB Output of lspci: 00:00.0 Host bridge: Intel Corp.: Unknown device 2578 (rev 02) 00:01.0 PCI bridge: Intel Corp.: Unknown device 2579 (rev 02) 00:03.0 PCI bridge: Intel Corp.: Unknown device 257b (rev 02) 00:1d.0 USB Controller: Intel Corp. 82801EB USB (Hub #1) (rev 02) 00:1d.1 USB Controller: Intel Corp. 82801EB USB (Hub #2) (rev 02) 00:1d.2 USB Controller: Intel Corp. 82801EB USB (Hub #3) (rev 02) 00:1d.3 USB Controller: Intel Corp. 82801EB USB EHCI Controller #2 (rev 02) 00:1d.7 USB Controller: Intel Corp. 82801EB USB EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev c2) 00:1f.0 ISA bridge: Intel Corp. 82801EB ISA Bridge (LPC) (rev 02) 00:1f.1 IDE interface: Intel Corp. 82801EB ICH5 IDE (rev 02) 00:1f.2 IDE interface: Intel Corp.: Unknown device 24d1 (rev 02) 00:1f.3 SMBus: Intel Corp. 82801EB SMBus (rev 02) 01:00.0 VGA compatible controller: nVidia Corporation NV28GL [Quadro4 980 XGL] (rev a1) 02:01.0 Ethernet controller: Intel Corp.: Unknown device 1019 03:01.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02) Base System Installation Checklist: Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [E] Detect hard drives: [O] Partition hard drives: [E] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [E] [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Comments/Problems: The debian-installer was invoked with expert26 at the boot prompt. Load installer modules: [E] The unavailable modules, and the devices that need them are: e1000 (Intel Corporation 82547EI Gigabit Ethernet Controller) The unavailable modules, and the devices that need them are: ide-scsi (Linux IDE-SCSI emulation layer) -> The missing Ethernet module can be severe for continuing the installation over the net. Partition hard drives: [E] On exisiting ext2/ext3 partion, the following unrecoverable, repeating error message occured: This ext2/ext3 filesystem has a rather strange layout! Parted can't resize this (yet) -> Thus, I decided to let the debian-installer format the root partition with ext3 again, which did not produce an error anymore. -> I've decided to install the kernel-image-2.6.3-1-386 Reboot: [E] After kernel decompressing, the PnPBIOS section and the following messages, a kernel panic occured: general protection fault: 0000[#1] CPU: 0 EIP: 0098:[<00001013>] Not tainted EFLAGS: 00010097 EIP is at 0x1013 (now come a lot of stack outputs) Code: Bad EIP value <0>kernel panic: Attempted to kill init! I hope this helps! With kind regards, Dirk Kostrewa. -- **************************************** Dirk Kostrewa Paul Scherrer Institut Life Sciences, OFLC/110 CH-5232 Villigen PSI, Switzerland Phone: +41-56-310-4722 Fax: +41-56-310-5288 E-mail: [EMAIL PROTECTED] http://sb.web.psi.ch **************************************** -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
