Debian-installer-version: http://cdimage.debian.org/pub/cdimage-testing/daily/i386/20040517/sarge-i386-netinst.iso
uname -a: Linux videoconf 2.6.5-1-386 #2 <date> i686 GNU/Linux Date: 05/18 one hour ago Method: netinst CD.
Machine: Toshiba Dynabook PAG6X18PME Processor: P4 1.8GHz Memory: 256 MB Root Device: IDE
Root Size/partition table:
Disk /dev/hda: 60.0 GB, 60011642880 bytes 16 heads, 63 sectors/track, 116280 cylinders Units = cylinders of 1008 * 512 = 516096 bytes
Device Boot Start End Blocks Id System /dev/hda1 * 1 115287 58104616+ 83 Linux /dev/hda2 115288 116280 500472 f W95 Ext'd (LBA) /dev/hda5 115288 116280 500440+ 82 Linux swap
Output of lspci:
0000:00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04) 0000:00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04) 0000:00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02) 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42) 0000:00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02) 0000:00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio Controller (rev 02) 0000:00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem Controller (rev 02) 0000:01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 460 Go] (rev a3) 0000:02:06.0 USB Controller: NEC Corporation USB (rev 41) 0000:02:06.1 USB Controller: NEC Corporation USB (rev 41) 0000:02:06.2 USB Controller: NEC Corporation USB 2.0 (rev 02) 0000:02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) 0000:02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42) 0000:02:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to Cardbus Bridge with ZV Support (rev 33) 0000:02:0d.0 System peripheral: Toshiba America Info Systems SD TypA Controller (rev 05)
Base System Installation Checklist:
Initial boot worked: [O] Configure network HW: [O] Config network: [E] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O]
Comments/Problems:
"no DHCP client was found. This package requires pump or dhcp-client." when configuring the network. But obviously it should work: I just put in a dummy config, and after the reboot I write a simple /etc/network/interfaces with DHCP, run dhclient and it works.
I also met another error (for several reasons I did the install twice) in only the first of the installs: after the "network HW detection", I had a message like "could not load some modules which are not available yet", and it listed SCSI and IDE related modules, but after it seemed to work fine.
Finally, I could not find out how to do personnalized partitionning, for example leave an empty partition: the manual says one can suppress a partition or change its size by selecting it by ENTER, but I only had access to info like what type of partition I wanted, where to mount it etc.
FL
-- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
