Hi all,
I would like to report a successfull installation of debian (throught a
netinst cd image) on a HP9000/785 (visualize c3000 workstation)
Package: installation-reports
Debian-installer-version: 2004-05-16 cd netinst image
uname -a:
Linux thebeast 2.4.26-64-smp #1 SMP Thu Apr 29 04:59:03 UTC 2004 parisc64
GNU/Linux
Date: 2004-05-16
Method: cd netinst image
Machine: HP9000/785 visualize c3000
Processor:
processor : 0
cpu family : PA-RISC 2.0
cpu : PA8500 (PCX-W)
cpu MHz : 400.000000
model : 9000/785/C3000
model name : AllegroHigh W
hversion : 0x00005bb0
sversion : 0x00000481
I-cache : 512 KB
D-cache : 1024 KB (WB)
ITLB entries : 160
DTLB entries : 160 - shared with ITLB
bogomips : 797.90
software id : 2006179580
Memory:
total: used: free: shared: buffers: cached:
Mem: 518520832 121638912 396881920 0 8441856 81375232
Swap: 99000320 0 99000320
MemTotal: 506368 kB
MemFree: 387580 kB
MemShared: 0 kB
Buffers: 8244 kB
Cached: 79468 kB
SwapCached: 0 kB
Active: 64252 kB
Inactive: 25756 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 506368 kB
LowFree: 387580 kB
SwapTotal: 96680 kB
SwapFree: 96680 kB
Root Device: /dev/sdb
scsi0 : sym53c8xx-1.7.3c-20010512
scsi1 : sym53c8xx-1.7.3c-20010512
blk: queue 000000002fc6c040, I/O limit 4095Mb (mask 0xffffffff)
sym53c896-1-<5,*>: FAST-20 WIDE SCSI 40.0 MB/s (50.0 ns, offset 15)
Vendor: IBM Model: DCHS04Y Rev: 6363
Type: Direct-Access ANSI SCSI revision: 02
blk: queue 000000002fbede40, I/O limit 4095Mb (mask 0xffffffff)
sym53c896-1-<6,*>: FAST-20 WIDE SCSI 40.0 MB/s (50.0 ns, offset
15)
Vendor: COMPAQ Model: ST32171WC Rev: 0684
Type: Direct-Access ANSI SCSI revision: 02
blk: queue 000000002fbedc40, I/O limit 4095Mb (mask 0xffffffff)
Attached scsi disk sda at scsi1, channel 0, id 5, lun 0
Attached scsi disk sdb at scsi1, channel 0, id 6, lun 0
SCSI device sda: 8813870 512-byte hdwr sectors (4513 MB)
Partition check:
/dev/scsi/host1/bus0/target5/lun0: unknown partition table
sym53c896-1-<6,*>: FAST-20 WIDE SCSI 40.0 MB/s (50.0 ns, offset
15)
SCSI device sdb: 4110000 512-byte hdwr sectors (2104 MB)
/dev/scsi/host1/bus0/target6/lun0: p1 p2 p3 < p5 p6 p7 >
Root Size/partition table:
df -k:
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sdb5 634472 156890 443732 27% /
tmpfs 253184 0 253184 0% /dev/shm
/dev/sdb2 118964 7558 105059 7% /boot
/dev/sdb6 1047946 8245 983787 1% /home
Output of lspci:
bash: lspci: command not found
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [E]
Reboot: [E]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't
try it
Comments/Problems:
When I first installed the system everything seemed to work fine, but
when I rebooted it I found a problem related to the command string to
launch PALO (PA LOader). If you consider the partition 2 as /boot, the
default string is 2/boot/vmlinux instead of 2/vmlinux just because
2=/boot.
After a few tries we, the pa-team guys and I, figured out the problem
and now everything seems to be fine.
Thank you all for the great work
Regards
SteX
--
;-P ;-P ;-P
http://www.openlabs.it/~stex
GPG key: Stefano Melchior (stex) <[EMAIL PROTECTED]>
Key fingerprint = F6A3 6071 -- Keyserver http://pgp.mit.edu
Registered user #324592 on the Linux Counter, http://counter.li.org
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
