Package: installation-reports Debian-installer-version: http://gluck.debian.org/cdimage/testing/sid_d-i/alpha/20040216/sarge-alpha-netinst.iso uname -a: Linux hakan 2.4.24-grsec #1 Tue Feb 17 14:31:04 CET 2004 alpha unknown (this is after the install & self compiled kernel based on Debian 2.4.23) Date: 17.2.2004, approx. 9:30 MEZ Method: Booted from CD, no (user visible) net access occured Machine: XP1000 Processor: 20264 alpha CPU Memory: 256 MB Root Device: SCSI, /dev/sda (was properly detected and handled) Root Size/partition table: (See below for details) Output of lspci: lspci 00:07.0 ISA bridge: Contaq Microsystems 82c693 00:07.1 IDE interface: Contaq Microsystems 82c693 00:07.2 IDE interface: Contaq Microsystems 82c693 00:07.3 USB Controller: Contaq Microsystems 82c693 00:0b.0 VGA compatible controller: Texas Instruments TVP4020 [Permedia 2] (rev 01) 00:0c.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly NCR) 53c895 (rev 02) 01:03.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41) 01:06.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI (rev 06) 01:08.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [E]
Load installer modules: [ ]
Detect hard drives: [O]
Partition hard drives: [E]
Create file systems: [O]
Mount partitions: [O]
Install base system: [E]
Install boot loader: [E]
Reboot: [ ]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Full report below
Hello!
d-i booted, and everything went as expected up to "Configure and mount
partitions".
1. We want lvm, so we partitioned a small boot, a larger (512 MB)
partition (later swap, now ext2) and the remaining unknown. The
installer (fdisk, to be honest) detected the present bsd disklabel
(this machine is converted) and offered us the disklabel menu.
Partitioning went fine.
2. The installer did not update it's view after returning from
partitioning, still claiming the first partition to be swap (which
it was previously), and the other n/a. Partition was
a: ext2
b: ext2
c: unknown
3. Also we were offered reiserfs, which IMHO should not be an option
(or a warning should be given).
4. We pressed continue, and then we were in the "Partiton the Storage
Devices" menu, were it again wanted to install swap on a:
Later we realized that "continue" is not appropriate, we should
press "finish". This is a confusing user interface: What is the
difference between "continue" and "finish" (and analogously "Abort"
vs. Go Back").
5. In the menu point "Install the base system" we got stuck, because
it claimed:
Failed getting Release file cdrom/dists/Release.
CD-ROM integrity failed
./dists/sarge/main/binary-alpha/Release failed MD5
The downloaded ISO had a correct MD5 sum, also other bootable media
burned with our CD-ROM burner work fine (inlcuding woody install
CD-ROMs).
6. We poked around if we could choose anything regarding this release
file, but were unable. Debconf was already set to low.
7. CD-ROM integrity check failed also (from the main menu), and then
he went through hardware detection again, and now complained (he did
not do so before) that he could not load some modules (ide-scsi,
usb, ...) but again we could not proceed
8. We tried saving the logs to a floppy, but did not suceed. He did
not change neither an ext2 formatted nor a fat-formatted floppy, in
fact, even leaving away any floppy did not produce an error. The
menu (in all cases) simply vanished for a moment, and then
returned, without any indication of success or failure whatsoever.
If you need any additional information about this machine, please ask.
Greetings
Helge
--
Helge Kreutzmann, Dipl.-Phys. [EMAIL PROTECTED]
gpg signed mail preferred gpg-key: finger [EMAIL PROTECTED]
64bit GNU powered http://www.itp.uni-hannover.de/~kreutzm
Help keep free software "libre": http://www.freepatents.org/
pgp00000.pgp
Description: PGP signature
