Package: installation-reports INSTALL REPORT
Debian-installer-version: http://www.mmweg.rwth-aachen.de/~sebastian.ley/d-i/netinst-image-i386/daily-2003-11-19/sarge-i386-netisnt.iso. The date on the file is 2003/11/22. uname -a: Linux siegle 2.4.22-1-386 #9 Sat Oct 4 14:30:39 EST 2003 i686 GNU/Linux Date: 2003/12/12 1:30 p.m. EST Method: How did you install? A:net What did you boot off? A:cd If network install, from where? A: carroll.aset.psu.edu Proxied? A: no Machine: Dell precision 420 Service tag: H5115 Processor: PIII 733 Memory: 384MB Root Device: 25GB IDE disk /dev/hda or /dev/ide/host0/bus0/target0/lun0/disc Root Size/partition table: Command (m for help): p Disk /dev/hda: 27.3 GB, 27373731840 bytes 255 heads, 63 sectors/track, 3328 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 * 1 510 4096543+ b W95 FAT32 /dev/hda2 * 511 753 1951897+ 83 Linux <-----/ /dev/hda3 754 3282 20314192+ 83 Linux <-----/usr /dev/hda4 3283 3328 369495 5 Extended /dev/hda5 3283 3328 369463+ 82 Linux swap Output of lspci: siegle:~# lspci 00:00.0 Host bridge: Intel Corp. 82840 840 (Carmel) Chipset Host Bridge (Hub A) (rev 01) 00:01.0 PCI bridge: Intel Corp. 82840 840 (Carmel) Chipset AGP Bridge (rev 01) 00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) 00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02) 00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) 00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) 00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02) 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 04) 02:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) 02:06.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01) 02:0e.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) 03:0a.0 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01) 03:0a.1 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01) Base System Installation Checklist: Initial boot worked: [X] Configure network HW: [X] Config network: [X] Detect CD: [X] Load installer modules: [X] Detect hard drives: [X] Partition hard drives: [E] Create file systems: [X] Mount partitions: [X] Install base system: [X] Install boot loader: [X] Reboot: [X] [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Partition hard drive: It was probably just me, but I could not figure out how to make an extended partition with logical partitions inside of it using cfdisk. Comments/Problems: <Description of the install, in prose, and any thoughts, comments and ideas you had during the initial install.> Install was simple. Wrote the ISO to cd, booted the cd. It found all my hardware. I pointed it to carroll.aset.psu.edu and away it went. Questions/comments: When I run lilo I get this message and am unsure of what I should do to solve this: siegle:~# lilo Warning: '/proc/partitions' does not match '/dev' directory structure. Name change: '/dev/ide/host0/bus0/target0/lun0/disc' -> '/dev/hda' The kernel was compiled with DEVFS_FS, but 'devfs=mount' was omitted as a kernel command-line boot parameter; hence, the '/dev' directory structure does not reflect DEVFS_FS device names. Added Linux * -Jonathan -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
